My 1999 F250 won't start ever since I replaced the o ring where the dipstick meets the oil pan. Started it when I was finished it ran for a minute and shut off, the truck was on a slope my low fuel light was on. I have it sitting on the flat now but still not starting but turns over?
View 1 RepliesI just replaced the head lights on my 2001 f250 it had the sealed beam one-piece glass headlights and I replaced those with regular headlights and when I went to get bulbs I found out after I get home the connector is different from the new bulbs. the new bulbs fit correctly but I can not hook plug them the plug has 3 connectors that have two connectors level and one is higher than the other two and the new bulbs the three prongs are level.
My question is. is there another bulb that will fit and plugin and if so what is the part number? is there a adapter that I can get that will allow the factory plug to work? or will I need to cut the old plug off and splice a new connector on?
I plan on replacing the brake lines on our 1999 Ford F-250 Super Duty. The rear line blew out right by the hose, on the framerail. All five lines, all five hoses. What size lines? Looks like front two are 3/16", rear two over the axle are 3/16", and the rear line in the frame is 1/4".
We are removing the bed (2013 bed) to make things easier. I am thinking fuel lines and parking brake cable while the bed is off. I have stainless steel hoses from KLM performance and I am also planning on replacing the rear rubber hoses. Obviously I'm using nickel copper line. There shouldn't even be an option for other brake line.
[URL].....
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 RepliesI'm looking at replacing the valve cover gaskets on my 02 f-250, it's a 7.3L.
Looking at them on line there are many different brands. What have you used on your 7.3L, and which has worked the best for you?
I am having some trouble with my 4R100 overheating.
Truck is a 2001 F250 XLT 7.3L with 244k miles on it. According to previous owner, the transmission was replaced around 185/190k but there was no paperwork to prove it.
I recently had a leak from one of transmission lines coming into the bottom of the radiator (the one on the passenger side). I replaced it and topped off the little bit of fluid that leaked out. Last weekend I installed a temp sensor in the transmission and hooked it up to my pillar gauges. The first few days driving with it, the temp was at/around 180 degrees, 25-30 degree outside air, unloaded on the highway averaging 70-75mph.
Today on the way home, the temp got to 180 after 35-40min of driving then continue climbing. I pulled off the highway after 1.5hrs and the temp was almost at 210 degrees. I let it idle for 5-10min and the temp didn't change. I turned it off and let it sit for 15 min. Upon starting it back up, the temp had dropped to 180. I continued driving and the temp climbed back up to 210 within 35 minutes. (65-75mph, 24 degree outside temp, unloaded). Once off the highway I averaged 35-45mph on the back roads to my house. The temp started to drop back towards 180 degrees.
Before I start throwing money at it, and installing a 6.0 cooler etc. I am thinking there is something else wrong here. I am going to look at new lines and replacing/repairing the bypass valve on the transmission. I am driving 2hrs to work each way and thats when the temp really starts to go up. The fluid doesnt smell burnt, its still nice and red. I am going to try and flush the lines this weekend and see if something is plugged/caught. I ordered an inline filter today and will put that in with a new hose from the transmission to the radiator (old one is rusted).
Two weeks ago did a road trip to NH from RI and i heard a slight dragging only at low speed (10-15mph) in my left rear tire. figured the caliber was dragging a little, it was. Before arriving in NH the brake light came on. Long story short i get back to RI and the left side noise gets worse and starts to lock up. I finally replace the rotor which was warped, pads, and caliper which was bad.
Was driving it same day and still here the same dragging and screeching noise and the brake light is still on. On my way home the left side locked up at low speed without hitting breaks and slid the truck, mid you all parts are new on that side. I am not sure what it could be at this point something in side the axle?
Changing tranny fluid/filter today, all has been going great until I went to take the filter o-ring out that didn't come with the filter. It will not come out! made a hook tool out of an old tooth brush like someone on here did, o-ring wont budge. Tried a hook pick, it wont dudge (actually bent the tip on the pick and started to tear the o-ring). Everything is ready to go back together and get filled, but this stupid o-ring will not come out!
View 3 RepliesI'm replacing tow mirrors on my 2004 F250 with 2008 mirrors. Both are factory Ford mirrors. Need wiring diagram since connectors and wires are different. They both have power mirrors, turn signals, heated mirrors, but are not power retract or fold.
View 1 RepliesOk I have a p1316 code so I was told to change valve cover gaskets so I did. Now starts for 4 sec and dies, what is going on....
View 2 RepliesI have a 2000 F250 with a V10, that won't start or turn over. I replaced the solenoid on the fender well, auto store check the starter 3 times and said it was good, new battery installed and same issue of not starting.
Here is a video of what it does when attempting to start : F250 starting issue - YouTube....
Where and what to look at?
I have a 2000 f 250 that will not start... I have replaced many parts all electronic sensorsm the past week i have spent in the neighborhood of 1800.00 on this truck. Cps, icp, idm, ebps, fuel filter, new oil, hpop level good, gpr, all new need starting........
View 4 RepliesFrom reading some of the posts on here it seems this is an air bag warning. 5 chimes five times in a row. The fuze is fine and there are no warning lights on the dash.
View 5 RepliesAfter replacing fuel filter, pump relay, and air filter for good measure my 2002 f250 v10 gas engine still wont start. What to do?
View 13 RepliesMy trouble is upon turning key to start everything goes dead (no power to anything). Does not always happen, sometimes she starts just fine.
After the power cut out if I turn key off, wait a minute, then back to on position she will sometimes come back as normal or sometimes the on "ding" will chatter and dash lights will be dim.
I have checked batt connections, starter/solenoid connections, block ground connection. All seems fine. Get same problem when I jump starter with screwdriver. Been suggested to me ignition switch to blame.
I have a '99 F-250 super duty with a 5.4 L engine and I am having trouble starting it. Initially it wouldn't turn over at all, so I had the battery checked, it was fine, and after charging it the engine would turn over very, very slowly once or twice then stop. I then replaced the starter and now it turns over very erratically but wont start.
View 4 RepliesLet me start out by saying that I have exhausted every option that I have read on every thread that I could find on the internet regarding my son's 2002 7.3L not starting. What I have is no 12v power to the starter solenoid at the starter when I crank the key. What we have done so far, had the starter and both batteries tested, all good. Swapped out the starter motor fuse and the starter relay. Tried a new ignition switch and a new trans position sensor. Found major corrosion in the fusible link junction box on the drivers inner fender so we cut out the fusible links and put in a temporary jumper wire, still no crank. I have power to the dash, power on the power cable at the starter. I can jump the terminals on the starter and the starter engages. I found the shifter linkage bolts loose under the dash and tightened them up also. We have been struggling with this for 3 days, out in the lovely Michigan weather, since it couldn't have died in his parking spot in our heated shop, and I am completely frustrated. Are we overlooking something glaringly obvious?
View 11 RepliesMy '01 f250 7.3 has gotten hard to start. It seems to maybe be due to cooler weather, but not always. I have been told that there is some sort of valve in the fuel tank that could possibly cause this when the fuel gets around a 1/4 tank or so. But, it's doing it at any fuel level. But it doesn't do it all the time. I do notice it more in cooler weather. Anyway, when I try to crank it, I'll let the "wait to start" light go off and then wait a bit more. I'll turn it over and it almost as if the batteries are weak.
I'll stop and give it a few seconds and turn it again and it will normally start. But sometimes I'll do this 5 or 6 times and it will finally fire. But the more I have to try, it's like fuel builds in the cylinders and it smoke like a coal train for a minute or so. Almost like gas motor that has been flooded. But the smoke burns off and it runs like a top. I was thinking the batteries may be weak , but sometimes the starter will spin the motor with no trouble at all. I'm at a loss. Is it possible for fuel to drain from the system causing it to have to reprime itself? Here lately the smoking has me concerned even though it clears up.
I'm in a real jam because my work truck won't start. 1999 F250 7.3 Diesel 157k mi. - Air and fuel filters were replaced in the last 500 miles. This pup ran fine when I parked it last Wednesday before the holiday.
Checked for start last night because I'd been having battery issues, Both were replaced the previous week. It's cranking good but just won't start, not even a bit. No wait to start light, oil level is good, can not get obd reader to link.
The truck starter and radio would magically turn on and off after the first rain, it was hard on the starter and I had to replace the starter and the cause of that problem was the vacuum line coming from the brake booster running over the top of the wires in the 4 plugs attached to the driver side fender. It rubbed through exposing the wires and got wet connecting them. I cleaned them and put the electrical tape silicone and then it has been working fine for a couple months.
Now every time I try to start fuse #20 blows. So far I have traced the wire that goes through fuse 20 through the firewall being the blue wire with a orange stripe on it it goes through the top plug upper left most wire. From there I followed it through the 4 wheel fender plugs the furthest plug from the firewall still being the blue with orange stripe. If I unplug that plug and try to start the truck it won't start but the fuse does not blow.
I then followed that wire all the way to the neutral safety switch. I hate tracing wires. (About 8 hours so far). I am thinking neutral safety switch. Also another thing I am thinking is weird is that blue wire with the orange stripe is grounded when the safety switch is plugged into the transmission and if it is unplugged is is not grounded. And I don't think it is supposed to be grounded because that is the hot wire when the key is in the start position.
Details about the truck : 1999 f250 diesel 7.3 super duty automatic 4x4 dated 4/99
I have taken pictures of the plugs and wires I was going to post it but don't remember how.
I have a 2002 f250 superduty 5.4 4x4 around 317xxx original motor and trans. When it's cold out it won't start at all I have to use starting fluid but once started it will start right back up. Did the plugs fuel filter cleaned the intake and sensors still have a problem plenty of fuel pressure plenty of cranking amps brand new battery and Alternator. It just cranks and cranks when it's warm out fires right up. Runs smooth no lack of power or misfire no codes are being thrown also.
View 14 Replies