I was driving my 99 f250 superduty and out of no where it sounded like i had blown a tire started to shake for at least 3 or 4 seconds pulled to the side of the road got out and check tires were good, got back on the road with no more problem.
View 1 RepliesI have a ford f250 with a 5.4l 2v engine and lately it started to shake when it idles. i have changed all the ignition coils and spark plugs, the injector are fine, but i cant seem to pinpoint the problem. the weird thing is that there are no codes. the fuel trim on bank 1 is around -8 and bank 2 is at almost positive 20 and higher.
View 14 RepliesI have a 99' f250 I purchased a few months ago. Here's what happened. Today I was driving down the road and it started to surge. I pulled over and shut the truck off. When I went to start it, the motor turned over slow for a sec and then clicked. When I put a jump pack to it, it fired up. I took it home with the jumper still hooked to it and checked voltage. The alternator was throwing 33.4 volts!! I went to the auto parts store and bought a new battery and alternator. Now the battery shows 11.7 volts steady. The alternator still reads 33.4. Also, if I unplug the positive lead while it's running, the truck shuts off. And one more thing. If the key is off and I reconnect the positive lead, I can hear the fuel rail pressurize. What is going on? I hate electrical gremlins.
View 6 RepliesThis morning while driving cold a fuel leak started on my truck it's a very heavy leak wondering what are the most common leaks on an 2003 F250 6.0L are so I can start there.
View 3 RepliesI have a 2011 f250 6.2 cclb and it shakes around 70 to 75 mph. Not terribly but enough to annoy the crap out of me. Now I have put new tires on it recently, new Rancho 9900 adjustable shocks, I have it aligned regularly and tires rotated and balanced every 5000 miles or so. I have had two dealerships look at and my local shop and they can't see anything visibly wrong with it.
View 7 RepliesI have a 2004 superduty 250 4x4 with the 6.0. I am having a violent shake in the steering wheel mostly and can feel it in throttle at about 45 to 60 and at 72 there is s growel. Have changed tires, wheels checked all ball joints tie rods wheel bearings ujoints. Don't matter brakes on or off, od on or off nothing changes it. I really don't know what else to check.
View 10 RepliesWhen my truck is parked, I go to the rear tire and shake it back and forth and hear a slight clunking noise from either the tire or rear end. Its like the axle is making the noise?
2000 7.3 Power Strke Super Crew 4x4
Have a 2006 F350 5.4l that is mainly used as a plow truck. I drive it at least once a week when not plowing just to make sure it runs ok, etc. Only put on about 2,500 miles per year. Keep it in good repair - not by me, but by the dealer or mechanics.
Problem - last two times I started it, it started ok but runs real rough for about ten seconds. Sounds like the engine is going to die. After about ten seconds, it "catches" and runs normal. Have no problems when driving it. If I restart it, it doesn't do this, so it seems to only happen when the engine is cold.
Battery was brand new back in Sept. All plugs were replaced maybe 3 years ago, as was the cat converter and muffler. Run non-ethanol fuel. What might be causing it before I bring it in.
My 1999 f250 superduty with the 5.4 was sitting in front of my house, and started all by itseft, did not have keys in it either and the doors were locked. I ran out thinking someone was stealing it but nope,? As far as I know it does not have a remote start either,i have owned it for the last two years and it has never happened before. It is a lariant edition also .
View 14 RepliesI just recently purchased my 1999 ford F-250 superduty V8 5.4 5 speed with 144,00 miles and I'm having a issue with the clutch pedal sticking in and then it will pop out after a couple seconds. It will stick more when I come to a light and have my foot on the clutch but the pickup drives fine and there is no slipping of the clutch. I have never experienced this issue before in any rig I've owned. so I'm a little lost at the moment.
View 2 RepliesI have a question about a possible leak. As I never really paid attention to it until of recent days, I noticed that my a/c is switching to defrost while driving for approximately 15-20 seconds then I let off the petal. Would it be time to search for a leak or could it be a solenoid issue. Also why we are on the subject would this have a negative effect on my mpg. I'm usually around 9.5 hwy and 8 around town, 6.5-7 towing 10k trailer. 06 350 cc lb v10 4.10's Factory 275/65/20's 69k miles...
View 1 RepliesMy 1999 F250 V10 has started to lose power off and on. It will run fine then when I stop at a light or sign, then when I take off it runs like I pulling something heavy. If I stop again it goes back to normal sometimes. 161000 miles. No check engine light is on. Motor idles perfect and sounds great. I don't know anything about motors...
View 4 RepliesMy 2000 F-250 6.8L V10 has a choppy idle during the first 30 or so seconds after a cold start up in the morning then it smooths out and drives perfectly. If I were to place the truck in gear during the choppy idle, it would not die and throttle response would be fine.
I cleaned the MAF sensor and checked the PCV elbow for cracks (no cracks). It idles at about a 1000 rpm during a cold startup then drops to about 750 rpm according to the dash tachometer. The truck has 187,000 miles on it.
As I am driving everything goes dead radio, windows, dash, alarms, everything then turns on a usually 30 seconds later. is it a ground? is it a sensor that's getting to warm? is it a loose wire? where should I start??
View 6 RepliesI have a 2001 f250 superduty 7.3L diesel and my air conditioner just randomly started blowing HOT south texas air. I tried to recharge it with refrigerant but the gauge said that it was over charged as soon as I plugged it into the low side port. What is wrong???
View 5 Replies2003 f250 5.4 86000 miles. When I start the truck, "especially after it sits a day or more" it starts to fast "Rushes". Like the gas pedal is all the way to the floor. I have taken it to the Ford dealer and they say they can find nothing wrong. They say all fords start up fast but I know this cannot be right. If I start it and let it run awhile then start it again it starts much slower. It only rushes like that a second or two and slows down. Today I noticed that when it started all the gauges pegged out. The speed indicator went up past 100mph sitting still in park. Then they all dropped down to zero then back to where they should be.
View 3 RepliesI have a 2002 Ford F250 Superduty with a 7.3 diesel. Brakes started sticking on it. I replaced all the calipers cause the boots were starting to crack but not leaking. All four brakes are still sticking. I can drive a little ways and then the brake peddle feels funny and they start dragging all four. I can loosen the bleeder and brake fluid will spray out and release the brakes for awhile.
View 4 RepliesSo out of nowhere, my tranny started over heating. Got up to 210. It usually runs in the 140-150 range. I have the 6.0 cooler, and 7500 miles on the synthetic fluid. My cooler lines to the radiator were ice cold. I crimped my bypass and this seemed to fix it a little (I know this is a no no), I did the flow test before driving it and it passed. It seems to heat up the most at stop lights in gear. It drives fine, no slipping, no chattering. I also dropped the pan, had some stuff on the magnet, replaced the filter too. It doesn't seem to heat up as bad now, goes to about 190. I will install the new bypass tomorrow when it comes in from the ford dealer. Whats causing the heat? BTW truck has a 4" lift with 35's no other mods.
View 4 RepliesI have a 2011 F250 with the 6.2 gas engine. I have been having a problem that the dealership says there is nothing they can do and have never heard about.
After the truck sits all night I get in and drive it for 10-15 min. It gets warm and I get out turning it off. When I come back about 15-45 min later I start it up and go to leave. As I pull out and start to accelerate in first gear the truck goes to an idle for about 2-3 seconds. I push the gas pedal and get no response. After a couple of seconds it picks up wherever you have the gas pedal. If you have the pedal to the floor it jumps you forward. This is not putting on any lights and the computer is not throwing any codes. According to the dealership the computer is telling them there is nothing wrong.
This has happened 12 times in the past 6 months. It has happened since I bought the truck. I have just started documenting it as of 6 months ago. It is not something I can make it do on command. After it happens once it doesn't seem to do it again for a week or two. I have 31000 miles on the truck. The dealership has had it for 4 days now and can't seem to get it to happen for them.
My v10 has a cold miss when i start it in the morning no matter what the temp. It misses until it gets up to operating temp.then it runs fine all day with a slight miss.
- Changed plugs,
- Changed pcv,
- Changed iacv,
- Cleaned map sensor,
- Changed tube to pcv,
No codes. Its running as if it had a carb and the choke is closed. No smoke, tach. idles between 750 down to about 500, until it warms up then tach. Stays steady.
I am new to being an F250 owner. Just recently purchased a 2000 F250 SD 4x4 with the 5.4 and a 5 speed trans. Got a pretty good deal on it, because I knew some work had to be put into it, and do plan on dropping the trans. Currently, if the truck has been sitting for a little bit, not cool, but not running for a little bit, when I start it, whether it is in gear or in neutral, there is a noise coming from what seems to be the clutch area.
After a couple minutes of driving, this noise goes away and all sounds as it should. A little bit of researching turned up the possibility of the throw out bearing being bad, however, I found other posts online that doubt this. Another symptom that I assume is connected is that if I go to put it in reverse at 0mph from neutral, it grinds.
In order to go into reverse, I have to press in the clutch, put it in first, then put it in reverse, at which point it goes in no problem. I had already planned on replacing the clutch because it seems to me that would be the logical choice as to where the problem originates, so no issue there. But perhaps I'm wrong??