Ford Super Duty (1999-2016) :: F250 Has Power But Will Not Crank
Nov 27, 2016
Ok I have a 99 f250sd v10 with 180k miles. Original owner and have most work my self over the years. Son took the truck to fill it up, started fine ,filled it up and now will not start. It has power but will not crank. Tries to but no good. I was thinking battery died. New battery same results. Sort of tried to start but not turning over. With the new battery i tried several times then nothing. No power at all. No lights, nothing. So I put the old battery back in and still no power at all. I'm thinking the starter is toast and my repeated attempts to start that I pulled too many amps and blew a master fuse? It stilling in a parking lot until tonight when I can tow it home. Where to start.
View 9 Replies
Advertisement
I have a 99 f250 sd with v10 that has no power. Will crank, idle and die sometimes. Getting codes p0351 - p0355. No power when driving.
View 11 Replies
2001, F250, Lariat, Super Duty, 7.3 engine with towing package.
It ran seemingly perfect when I parked it and it sat for maybe 10 days to 2 weeks and wouldn't crank. Battery is fine and fully charged. Glow plug heaters work OK. Engine spins really fast, almost like it had no compression. (Not sure though) Temperature in the 30's -50's. I did some research on line and decided to change the Cam Positioning Sensor (CPS). Didn't work, still won't crank. I originally tried my Cheap Harbor Freight OBDII . (Don't waste your money, IMO). What should I troubleshoot next/ or try.
View 5 Replies
Let me start out by saying that I have exhausted every option that I have read on every thread that I could find on the internet regarding my son's 2002 7.3L not starting. What I have is no 12v power to the starter solenoid at the starter when I crank the key. What we have done so far, had the starter and both batteries tested, all good. Swapped out the starter motor fuse and the starter relay. Tried a new ignition switch and a new trans position sensor. Found major corrosion in the fusible link junction box on the drivers inner fender so we cut out the fusible links and put in a temporary jumper wire, still no crank. I have power to the dash, power on the power cable at the starter. I can jump the terminals on the starter and the starter engages. I found the shifter linkage bolts loose under the dash and tightened them up also. We have been struggling with this for 3 days, out in the lovely Michigan weather, since it couldn't have died in his parking spot in our heated shop, and I am completely frustrated. Are we overlooking something glaringly obvious?
View 11 Replies
I have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 Replies
On occasion, the last 2 weeks, my truck doesn't like to start, sometimes it will start to crank for one second and then quit. i've tried moving my gear shift through the drive selection range (park, neutral, reverse and drive). i just replaced the starter relay on the fender well because i can always start the truck by jumping across the terminals... no joy. So now ( i think) my issue is between the key switch and the starter relay. i replaced the neutral safety switch about 18 months ago.
99 F250 V10 short bed, 123,000 miles ....
View 1 Replies
I have been trouble shooting a no crank no start issue for a couple years now. Been back to the dealer several times to no avail. Very long story, with all due respect, don't suggest that I go back to the dealer on this. Not happening. Every once in a while the truck would strand me with no crank no start. It would read trailer brake module fault. Sometimes the security light would flash and the alarm would sound. Recently, I have had it on IDS and noticed that while it was doing this, IDS had no communication to the ECU.
I checked IDS with my other truck and it had good communication with that ECU so I know the computer/IDS works. Pulled battery cables and checked all the fuses... checked ok. Went back in the truck tried it, still no crank. Left key on, popped hood to listen for fuel pump... nothing. Went to pop cover off the fuse block and as soon as I touched it the fuel pump started whining. Went back in the truck and it started. Plugged IDS back in and had good communication and read ECU. I googled around for a part number but came up empty.
View 3 Replies
2002 F250 V10....
Ambient temp is 4-9 degrees
Step-son borrowed truck. I started it at 9 in the morn and moved it to a different parking spot on street. No problem starting.
Step-son came at 11 and took truck. It started no problem.
He drove it to work. At 5 p.m. would crank, but not start. A jump got it running.
On charger all night. Would not crank this morn. Would not crank even when jumped.
Are we looking at a bad battery or something else?
View 9 Replies
I'm having a problem with my 04 f250 6.0. I replaced my brakes rotors and calipers yesterday along with my fuel filters and after I took out my air filter to check it and put it back in my truck will no longer crank. When I put my key in the on position all of my lights and dings happen but I don't hear my fuel pump and when I go to turn it over I get nothing at all.
View 8 Replies
I have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 Replies
I have a 2004 Ford F-250 with the 6.0 egr has been deleted and so on. Truck has been very trustworthy until now... It all started last week. I would get in and it would fire right up, drive 15 miles to work all is still good. Time to go home try to start and it would act like the batteries were weak with a weak crank until it finally takes off and starts. This intermittent situation has been happening but I just assumed that the batteries were going bad. I drove to work this morning truck fired right up and now that it is time to go home the truck only has a weak crank and wont fire up. I tested the batteries and they were low on cranking amps.
Replaced them with two new batteries. The issue still exists and didn't change. After reading through threads I found that it could be the FICM I checked it out as was shown through the other threads. With the key on only it was reading 51 vdc with someone trying to start the truck it was reading 48-50 vdc... Yes the truck does have fuel in it and yes the oil is good to. It seems that there is something electrical going on for sure due to the way it has been an intermittent problem for a week or so. I am an aircraft mechanic by trade but can fix anything if I know where to start.
View 5 Replies
My '99 Super Duty does NOT have power windows; old school cranks. The door panel(s) are "no frilz", no storage pockets. I want to know if it's possible to get panels that DO have pockets and will "fit" my crank handles?
I could always just drill a hole into a door panel that has the pockets for the window crank, but, they all seem to come with power window setups (opening for all the power switches). Also, where I can get rugs to cover the floor - I just have a rubbery/plastic surface.
View 2 Replies
My 92 f250 5.8l 5 speed, out of no where when I try to start it I get absolutely nothing, when I put the key in the on position and short the solenoid it starts up that's how I've been starting it? When I try to start it regularly it's almost as if trying to start it without pressing the clutch it literally does nothing.
View 1 Replies
I have 1999 f250 powerstroke, batteries are fully charged but when you put key in ignition and turn you get nothing. No dash lights, no crank, nothing. I cleaned the battery terminals on both batteries, checked all the fuses under the dash and the hood.
View 9 Replies
I have a 2000 F250 7.3 manual tranny that was put away for winter storage and now will not start. Need it to get my weekend work done now that the snow is finally gone. Symptoms:
- not cranking
- no dash lights (no oil light, battery light, etc.)
- radio works
- head lights work
- key buzzer works
- can hear clicking when turn key (assume solenoid OK)
Put in two new batteries, fully charger and terminals are clean. Where should I start looking?
View 11 Replies
This is a 6.4L powerstroke, but this is not an engine specific problem. I have a no crank condition that appeared overnight while parked in the driveway. I CAN start it by using the solenoid connector wire near the air filter box and supplying 12v from + battery post. I THINK that eliminates batteries, solenoid and starter.
Now that leaves Trans range sensor or (NSS) and the ignition switch. I can test and get 12V (light) on the Blu/Wh wire from ign sw when turned to start, so that seems good. And as far as I can tell the trans range sensor is internal to the tranny, and I really don't want to go there if possible....
Also there are no codes on the Solus scanner I borrowed. And the voltage is showing as 11.7 on the scanner....is that low enough to prevent voltage from being sent to the solenoid thru the SJB and/or PCM even though engine will start as described?
View 14 Replies
Only got a click when turning key, in Park or Neutral. Made sure I had >12.4V from battery. Jumped starter solenoid with a remote start switch across main power line to starter and the 's' post, crank pulley almost moved, but didn't rotate. Removed belt, all pulleys rotate, but could not budge the crank pulley with a short breaker bar/socket, rotating clockwise from front. Removed starter, that upper bolt is a super pain! Not even sure I'll get it back in. Jumped starter solenoid again on the bench using a battery and jumpers, not the best connections, starter hesitated little bit, but opened up fully a few times, so I'm thinking it's ok (even though the power line from the solenoid to starter motor needs re-taping). Tried rotating flywheel from starter hole, no good leverage point, but no movement. Before I re-install the starter, how much torque should I be putting on the front crank pulley? Some say it should move easy enough cause the starter isn't that powerful. Others say remove the spark plugs to reduce compression? This truck is new to me, so I unfortunately have no history.
View 1 Replies
I have a 2005 f-250 King Ranch 5.4 triton engine...my problem occurs when i turn the key to start the pickup....i get a clicking sound and then nothing....when i use a portable jump starter, it fires right up...on the other hand, when i try to jump from a running vehicle i only get a clicking sound from the starter...
not sure what i should be testing...also, when i bought the vehicle it had been sitting for several months...for my test drive, they used a commercial charger/starter to fire the truck...i drove it about 10 miles, stopped, turned off the motor and 10 minutes later it wouldn't start...when i contacted the owner, he drove to me and "reset" the kill switch under the fuse box in the cab and then jump started the truck...
I drove it 40 miles home and for 4 days had no starting issues...on day 5 forward, i have had to use the portable jump starter every time...my battery shows 13 amps resting and drops to 5 amps when i try to start without portable jump starter...when i start it with the portable jump starter, it only drops to 10 amps...
View 7 Replies
The factory remote start is not working on my 2009 F 250. The red light is lit when I push the button, the doors lock and you can hear something engage in the engine but it does not crank it. If I keep holding the button the alarm starts to go off. When I walk up to truck the radio is on and I need to hit the remote start button to shut everything down before manually staring.
View 4 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
2001 F250 5.4 ... I'm losing my mind chasing a Gremlin. I've been having mostly intermittent starting issues with my truck. I've had the truck for a little over a year, after someone totaled my previous one.
It occasionally wouldn't start on the first attempt, but it got really bad in the last couple weeks.
I first thought it was a faulty inertia switch or wiring in that vicinity, as at one point after manually tripping and resetting the cutoff switch it would start, UNTIL I put the trim panel back. At this point I think that may have been a coincidence.
I eventually probed the switch and it tests as it should electrically.
I put in a new fuel filter and things were fine for several days, but it acted up again. That time was last Saturday. Got it to start and all was good until tonight. Now it won't go, and I've tried so many times that I can see the battery power is dropping.
Last Saturday I pulled the relays from behind the radio and cleaned 'em up real nice. Also, just to check another variable I swapped the two that matched.
I'm about ready to change the fuel pump, but I've heard so many people say they did that but the problem was something else. Not only will it costs hundreds of dollars, its cold out and we'll have to drop the tank in the driveway.
In addition to the relay, inertia switch and fuse, I have found some mention of faulty fuel pressure regulators causing issues. I'll pry the vacuum line off in the morning to see if I can detect fuel residue on the vacuum side. (There is some noticeable corrosion on the fuel rail in that area).
I REALLY want to make sure I rule everything else out before spending hours under the truck in freezing weather dropping the tank and changing the sending unit out.
On key-on there is a noise from the gas tank, but someone else listening described it as a click but no whirring.
I do hear the relay clicking behind the radio. (Also, I pulled them again tonight and put a meter to them. With 12V on the primary side, they click and the other side shows continuity on diode check, and about .2 Ohm on resistance mode.)
I went through a lot of trouble to get my spare out looking for the fuel control module before finding out my truck is about 3 years too old to have one too. What else to check?
View 3 Replies
