Ok so my F250 died last night. I read the Pcodes and came up with P2198 and P0506. I am pretty good with fixing the truck but need to know exactly what is wrong.
View 5 Replies2008, 5.4 liter, F250, with 6-speed manual transmission
My truck was running fine until I decided to clean my engine. I just wanted to remove the extra dust covering it, so I used a low pressure garden hose to wash away the dirt that had accumulated last winter and spring.
It started throwing codes like Fuel Rail pressure sensors, P0191, P0192. I had no power, and I could hardly drive the truck.
I figured I had some water in some connectors, so I checked around, but could not detect any moisture.
I kept driving it, and the problem got less severe. One warm summer day, I drove my truck for about an hour trip, and everything looked fine after this. Problem never came back.
I was even noticing that it was better on gas that ever before, I was doing 11liters/100km, in city driving.
Until one day (2 months later), I had to disconnect the battery to do some servicing on my truck (more that 30 minutes), and it started to run crappy again, having some piston misfire, throwing codes P2198 and P2196, (O2 sensors). No power, if I am very gentle on the gas pedal, I can manage it, but as soon as i try to accelerate, runs like crap, black smoke coming out of the exhaust.
The problem comes and goes, sometimes, the problem stops, and I can get going, no issues. Air filter is clean, even tried with no air filter, no differences., but it really sounds like bad air/fuel mixture.
2005 5.4l... Its giving me a code p0506 rpm to low idle air control system called for new one they said my truck don't have one said only up to 04 so what now truck idles rough n when u step on it it misses so bad its not funny feels like its laying over...
View 3 RepliesI replaced the head gaskets on a 2006 F250 6.0 Diesel, put it all back together and started it up. It ran great for a lil bit, then it started cutting out. It did this for about an hour then I killed it and it took a little bit to restart it, spinning over and over to get it to run, this took place several times. The engine died and now it will not start. I keep getting codes P2284 and P2290. What could be causing this problem??
View 9 RepliesI have a 2004 f250 6.0 diesel and my passenger window switch died today and I switched it with a known good switch and it still does not work but will work from drivers side .the switch doesn't even light up. Looking for a diagram or know the colours of the wires to switch Soni can test to see if the switch is getting power??
View 1 RepliesMy truck ran and drove then I changed my Steering Gearbox. After all that, I went to go start it, the trucked cranked and the batteries died. Hooked up the charger then and nothing, No start no crank. F250 2006 diesel 6.0 ...
View 14 RepliesHad an issue with the negative cable n had to replace the bolt n nut. Since then its been making weird noises under the dash n under the hood even when the key is off. Sounds like something moving around under there almost but i know there is nothing. Also making buzzing noise every 30 minutes or so for a few then stops. Separate noises n 2 separate issues tho
View 4 Replies05 5.4 F250 4x4. Keep getting those codes. Can't find any vacuum leaks. swapped rear O2 sensors. Fuel filter twice in last 11k miles last time was 1k ago. Will the 430 code cause the lean codes from a bad cat? I've been getting the 430 code for at least 4 mo's.
View 6 RepliesMy 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 RepliesThe engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 RepliesLong time follower, first time user. 99 F250 V10 180,000 miles: About a month ago I replaced both upstream oxygen sensors. I know have the following codes:
0135 and 0155 for Upstream Heated Oxygen Sensor Heater HTR 21 and 11
Circuit Malfunction Bank 1 and 2
1409 for Exhaust Gas Recirculation Vacuum Regulator Solenoid Circuit
I checked fuses and PCM relay and all are good. I have 12 volts to both oxygen sensors and no noticeable wire burns. One of the possible causes given on code printout for 0135/0155 is to check for a disconnected hose to the EGR. All hoses are good. One of the possible reported fixes for EGR code 1409 is to repair oxygen sensor wiring. So my question is: Are these codes related. If I replace the EGR vacuum regulator solenoid, will this clear my codes from the oxygen sensors?
I have an intermittent problem with my 09 F250 Diesel. A few times now under hard acceleration I have had the trans seemingly get stuck in 3rd gear. The little service required wrench symbol showed up on info screen but after shutting off the engine no codes were present. A week or 2 later this happened again and I ran diagnostics through my Spartan tuner and got P0771 and P2704 for codes.
Again they cleared when I shut the engine off. Since this is an intermittent problem, only after hard acceleration, would it make sense to change tranny fluid, maybe do a tranny flush? Or am I off to the dealership for a rebuild?
2009 F250 Lariat Crew Cab Short Box
Spartan DashDaq
S&B Cold Air Intake
4" Flange-back w/6" Can
Package by Dirty Diesel Customs-Red Deer Alberta
I just got my 2005 F250 diesel out of the shop. The errors codes P0299 and P2263 were listed on the computer. The service done, was to clean carbon from turobo charger and service the EGR valve. I talked with the mechanic and he recommended that I use Cetane Booster Additive. What would the Cetane Booster do? How would it prevent the carbon build-up in the turbocharger? What should I do to prevent turbocharger carbon build-up?
View 3 RepliesMy '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
After finding that a battery was low and not getting charge, they found the alternator was bad. Replaced that. Next the battery that was low was able to be charged and did not effect the other battery. Both batteries have been load and charge tested and they both read 84% charged. I am told this is "good."
Next I swapped both fuel filters and did the oil change as well. I finally got a chance to get my friend to run his scanner on it. The results are injectors and FICM. The codes are PO261, 264, 267, 270, 273, 276, 279, 282, and finally 611. I guess this means that the FICM is toast.
I have tried salvage and no one has anything. I guess I still don't understand how this truck is capable of running daily with the computer throwing every code dealing with the injectors and the computer that runs them.
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies2 weeks ago I had the check engine light come up on my 2011 F-250 6.2 XLT. Did a diagnostic check and Codes P2098 and P2272 came up. Did some research and found out the second O2 sensor on passenger side had gone bad. I replaced it with a Motorcraft O2 sensor and cleared the code. It has not came back since. But still not getting the fuel mileage I got before. What else could be wrong?
View 5 RepliesI've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 RepliesTBC fault has been showing on my 2006 Ford F-250 for a couple of years dealer said it wasn't an issue--- check engine light has been on for months, then lost speedometer back in November. Intermittently radio and fuel gauge shut off while driving--- stared needing a boost in really cold weather for the last month.
Driving today my battery just died while driving and I had the truck towed to mechanic--- they put new battery in and ran electrical diagnostics. Saying that it might be timing chain/cam shaft OR electrical components for computer system... I'm lost and so are they and don't want to spend thousands while they diagnose the source.....