I bought a 99 f250 super duty with v-10. Ran great then I decided to hose off engine compartment. No pressure washer just running water trying to get all the dirt off now the engine sounds like its missing. Could I have a coil pack that got wet or is something else wrong.
View 3 RepliesI have a 2007 F250 4X4 6.0 diesel. When first started it idles extremely rough to a point it sounds like a old gas engine missing. But after it warms up for about 15 minutes it runs and idles like a new truck. I'm thinking it's the injectors if so is this something I can change/clean ....
View 2 RepliesI have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies99 F250SD V10. There are two connections on the heater core at the firewall. Is there an 'inlet' and an 'outlet' or does it not matter? Put a cummins in the truck, the V10 has been out for a while and cant remember which one is which.
View 5 RepliesNeed the fuel system diagram or schematic for my truck.
1999 250 superduty v-10 Ser# 1FTNF20S1XEC67940
Every time I run it I smell gas. I changed the f/p 6mo ago. While I was working on it I noticed there was a hole rubbed in a small hose. I assumed it was a return line (smelled gas before too) and when I fixed it the smell went away until lately. I dropped the tank,yesterday and didn't see any problems. Just need to find out what hoses go where so I can replace the hoses??
I have put a new steering pump on my 2002 f250 and all new hydraulic hoses. I plan to install a steering pump filter on the system to protect it from anything that is not steering pump fluid.
There are two intake ports to the steering pump. One is near the bottom of the pump and takes fluid from the steering pump cooler after it has left the steering gear. The other intake port is near the top of the pump and takes fluid from the booster.
My question is - which hose would be better to put a steering pump filter on? Is there anything wrong with putting a filter on both? I imagine the first intake hose is constantly circulating fluid and the other only circulates it when the steering wheel is used.
My uncles 1999 v10 started to leak from the high-pressure hose on the gearbox. Replaced the hose which lasted for a short time but is now leaking at the same spot. The hose swivels, is this normal, seems like a dumb design for a pressure hose. Also is there a certain trick to doing this hose? He also insists on using PS fluid instead of the ATF it calls for. Could this cause a problem with the seal?
Edit: Also the truck has been lifted on 35s since 16k miles and its now roughly at 170k. He tows with it as it is his work truck. But the truck is well taken care of.
I have a 2004 F-250 with a 6.0 and a 6-speed with 140,000 miles. It has been studded, and has upgraded injectors. ( Not sure on the size, they bored them at at the diesel shop that studded my heads.) Also have an EGR delete, with the EGR turned off on the SCT as well. I also have a SCT Livewire set on the 65HP tow tune.
Truck has always ran great in the year and a half I have had it. I changed the oil three days ago, and now I am getting a miss at idle. The trucks cranks right up and drives normally. Once it is at operating temperature, when I stop at a light it has a very noticeable miss. There is no surging, or change in RPM's at all. Just seems like it is cutting out every few seconds. This is also somewhat intermittent. FICM shows 49 volts always, even when this is occurring.
Also, this may be unrelated, my oil temperature seems higher since the oil change. Was around 192 water/197 oil while cruising 70 on the interstate. Now, its' more like 192/202. I've always ran Motorcraft 15w-40, and that is what I used for this oil change as well.
I see some people have a similar problem, but all the posts I've read involved fluctuating RPM's or surging, or both. Other than this, the truck cranks and runs just like normal.
I have a 05 f250 diesel 6.0 with 173k. Between 35-60 mph it has started a humming sound and when the throttle is released the sound stops. I still have power boost etc. Someone mentioned degas cap, turbo pedestal or turbo pipes cracked.
View 14 RepliesI'm trying to troubleshoot a leak on my 08' F250 with a 6.4 powerstroke. It's been dripping coolant when cold pretty aggressively. Once the truck heats up, the coolant leak seems to mostly go away.
Here's a picture of the drip, it's marked by a dart, so you can see the location from the top (second pic). The radiator house connection around the engine seems dry.
Pic from Top ....
What's hidden here that could be causing the leak?
Where this small leak coming from. Under my radiator hose. Took a pic of the leak.
View 8 RepliesWhere is the best/easiest location to run some wires from the cab to the engine compartment?
I need to run some wires for a remote start with alarm and a backup camera.
I have recently purchased an 04 F250 crew cab with the 6.0 power stroke, it has a cold air intake, 4inch exhaust from the turbo back and has a program in it but programmer didn't come with the truck. When I sit at a traffic light and go to leave on a green light the truck kind of hesitates or acts like it's missing out( maybe loading up) shoots out black smoke then runs fine, it doesn't do it at all the stop lights but does get irritating. If I get it flashed back to stock settings will the truck run normal with all the upgrades?
View 4 RepliesI have a 1999 ford f250 with a 6.8 liter v 10 engine. At about 40mph the truck will start missing and lacks power to accelerate further. This problem is intermittent. Some days it runs great and others the miss appears. Well I scanned and the code reader said that I had a misfire on cylinder 7. I took a chance and replaced the COP and the boot for that cylinder . Ran great for a day and then the miss came back. Same code again. What else might cause this? Are plugs difficult to change in these engines?
View 6 RepliesJust got a 2008 F-250, truck has the center console jump seat and the console lid is missing. Can you just buy a new lid or do you have to buy the whole thing? Cost? Places to buy?
View 4 RepliesMy v10 has a cold miss when i start it in the morning no matter what the temp. It misses until it gets up to operating temp.then it runs fine all day with a slight miss.
- Changed plugs,
- Changed pcv,
- Changed iacv,
- Cleaned map sensor,
- Changed tube to pcv,
No codes. Its running as if it had a carb and the choke is closed. No smoke, tach. idles between 750 down to about 500, until it warms up then tach. Stays steady.
I was washing my 2004 F-250 today and I looked down by the front passenger wheel well and I noticed a small chuck missing from the bottom of the frame. The other side in the same spot doesn't have it and at the spot in question, I noticed some sort of crack had been welded before. I never had any of that done to the truck. What about getting it fixed? get it fixed right away or keep an eye out for cracks. so far its just that hole and what looks like a welded crack above. everything else seems fine. I know a repair would be inexpensive and easy just to weld a steel or titanium plate on the spot.
View 11 RepliesI have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 RepliesI've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
So, I have a 2007 f250 with the 6.0. When she's cold she starts fine but runs rough like she has a miss. When she warms up the miss goes away and it runs pretty good. But if I shut it off it won't start for about an hour or so.
ICP sensor has been replaced.
FICM is putting out 50v
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies