Ford Super Duty (1999-2016) :: F250 V10 - Oxygen Sensor Codes Related To EGR System?
Jun 2, 2013
Long time follower, first time user. 99 F250 V10 180,000 miles: About a month ago I replaced both upstream oxygen sensors. I know have the following codes:
0135 and 0155 for Upstream Heated Oxygen Sensor Heater HTR 21 and 11
Circuit Malfunction Bank 1 and 2
1409 for Exhaust Gas Recirculation Vacuum Regulator Solenoid Circuit
I checked fuses and PCM relay and all are good. I have 12 volts to both oxygen sensors and no noticeable wire burns. One of the possible causes given on code printout for 0135/0155 is to check for a disconnected hose to the EGR. All hoses are good. One of the possible reported fixes for EGR code 1409 is to repair oxygen sensor wiring. So my question is: Are these codes related. If I replace the EGR vacuum regulator solenoid, will this clear my codes from the oxygen sensors?
View 2 Replies
Advertisement
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 Replies
After finding that a battery was low and not getting charge, they found the alternator was bad. Replaced that. Next the battery that was low was able to be charged and did not effect the other battery. Both batteries have been load and charge tested and they both read 84% charged. I am told this is "good."
Next I swapped both fuel filters and did the oil change as well. I finally got a chance to get my friend to run his scanner on it. The results are injectors and FICM. The codes are PO261, 264, 267, 270, 273, 276, 279, 282, and finally 611. I guess this means that the FICM is toast.
I have tried salvage and no one has anything. I guess I still don't understand how this truck is capable of running daily with the computer throwing every code dealing with the injectors and the computer that runs them.
View 14 Replies
I have a 1999 F250 super duty with a mean vibration at 70+ mph. It is a 5.4L manual trans manual 4x4 extended cab short box with around 250k miles on the body and 50k on the motor. It is a one piece drive shaft with the double knuckle at the t- case. it has had a vibration in the drive line since i bought i about a year ago. there is almost zero vibration at 60 mph but at around 70 the vibration starts to get really bad. The vibration is speed related because when i push in the clutch or pull it out of gear the vibration is still there. i seems to vibrate more when winding out in 3rd and 4th gear but that may just be because off the exhaust resonating or something. I have already done u-joints, balanced the drive shaft, put brand new tires on mounted and balanced, replace transfer case output bearing and both front hub assemblies. the vibration feels like it is coming from the trans or transfer case. every thing i tried made very little impact on the vibration. I'm a loss and i don't know what else to try. i know the throw out bearing an pilot bushing are bad and the clutch is well worn so ill be replacing that soon but i don't believe that is causing the vibration.
View 7 Replies
I have a 2000 motorhome on a f450 chasis. It has a V-10 with only two oxygen sensors up-stream from the catalytic converter. The monitors for the oxygen and oxygen heater sensors will not show "ready". I replaced both sensors and have driven it over 200 miles. They still show "not ready".
View 5 Replies
I recently bought a 2008 F250 with the 6.4 diesel indirectly from a dealership. The truck itself has 220,000ish kilometers, but the engine (as well as the turbos) are Ford reman that had about 12,000km when I bought it and I have only put about 6500km on it. It is already leaking oil but that is for another thread.
The reverse sensors, steering wheel controls and part of the stock 6cd radio have never worked. The towing system has errors as well. The fuel level sensor often has problems reading the new level after I put in fuel, but that is always fixed by disconnecting the batteries and forcing a hard reset.
I figured the steering wheel/cruise control problem was due to either a broken clock spring and/or the brake pressure switch. I replaced both those as well as the airbag because the horn relay failed closed when I put it back in the wheel. It did not fix the problem. The steering wheel buttons still intermittently illuminate, but the radio controls and cruise control buttons do not function regardless. The truck isn't giving any codes either.
The towing system will activate lights and brakes on a trailer as well as set the gain, but it will not detect that it is actually hooked to a trailer. I cleaned the pins, but I haven't looked any further into it. No codes for this as well.
The reverse sensors/system does not work. It will lock itself in "off". I am guessing this is because one or more of the sensors have failed, but I am skeptical that it would be just that given the trucks other problems.
The radio does work, but the auxiliary input/mode will not work. I ran the diagnostics on the radio and on 'Test 1' I got "SELF FAIL B1342 ECU" and "B2477 CONFIG". I tried to clear the codes, but I can't. I think this means the radio is kill.
View 6 Replies
I have a 2012 ford f350 6.7 diesel....I have the following check engine light codes..
P0073 Ambient air sensor circuit high output
P009a Intake air and/ambient air correlation.
I replaced ambient air sensor in passenger mirror and auto zone said to replace the air charge sensor. I have done both still have a check engine light.
View 1 Replies
05 5.4 F250 4x4. Keep getting those codes. Can't find any vacuum leaks. swapped rear O2 sensors. Fuel filter twice in last 11k miles last time was 1k ago. Will the 430 code cause the lean codes from a bad cat? I've been getting the 430 code for at least 4 mo's.
View 6 Replies
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
View 3 Replies
99 5.4 F250
Well, this truck i have had many many codes before. I cleared them and all went away except for p0155. I fixed my manifold leaks and cleared the codes. It came back on and i changed the o2 sensor, twice. Still on.
Ive checked the heater and input wires to the pcm and have .6 ohms each, so they are good with what appears to be no shorts. I dont know how to check the other 2 o2 sensor wires.
View 11 Replies
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
View 10 Replies
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 Replies
Ok so my F250 died last night. I read the Pcodes and came up with P2198 and P0506. I am pretty good with fixing the truck but need to know exactly what is wrong.
View 5 Replies
I have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 Replies
The engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 Replies
I have an intermittent problem with my 09 F250 Diesel. A few times now under hard acceleration I have had the trans seemingly get stuck in 3rd gear. The little service required wrench symbol showed up on info screen but after shutting off the engine no codes were present. A week or 2 later this happened again and I ran diagnostics through my Spartan tuner and got P0771 and P2704 for codes.
Again they cleared when I shut the engine off. Since this is an intermittent problem, only after hard acceleration, would it make sense to change tranny fluid, maybe do a tranny flush? Or am I off to the dealership for a rebuild?
2009 F250 Lariat Crew Cab Short Box
Spartan DashDaq
S&B Cold Air Intake
4" Flange-back w/6" Can
Package by Dirty Diesel Customs-Red Deer Alberta
View 5 Replies
I just got my 2005 F250 diesel out of the shop. The errors codes P0299 and P2263 were listed on the computer. The service done, was to clean carbon from turobo charger and service the EGR valve. I talked with the mechanic and he recommended that I use Cetane Booster Additive. What would the Cetane Booster do? How would it prevent the carbon build-up in the turbocharger? What should I do to prevent turbocharger carbon build-up?
View 3 Replies
I have noticed my trans temp gauge needle is dead center of the gauge even on a cold start. I thought my sensor was under the pan so I pulled it and did not see any sensor at all. Is there a external sensor?
View 5 Replies
I have the 2012 XL F-250 6.2 v8 , I have an ambient (outside air) temperature sensor that needs replacing, I ordered it and was told it is located in the passenger side mirror from the parts guy, there is a tap in the bottom of the mirror to access it, looking for a replacement type video link of how to do this, as I am not finding one via youtube, pulling the tab off on the bottom of the mirror I am not really seeing the part I have as a replacement in the mirror.. This is the XL version/work truck so ALL manual mirrors....
View 1 Replies
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
