Ford Super Duty (1999-2016) :: F250 V10 Misfire - Shaking At 80 KMH
Sep 3, 2014
I have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 Replies
Advertisement
2008 f250 standard cab long bed 2wd base model 5.4. This thing has been great for the last few years i i owned it but it developed a shake since i got new tires. My mechanic mounted 4 new Hercules Terra trac at 2's on my 18 inch wheels (275 70 18) and when i got the truck back it was shaking violently at anything over 45. Mechanic says the new tires are heavy and its affecting other things...sounds plausible. So here i am a month later with a New steering stabilizer, all new ball joints, new shocks, new u joints, and 1 new tire (he said 1 of the brand new Hercules had a broken chord). The shake is 80% gone but this truck is still not the same. Anything after 65mph and it has a feint wobbly bouncy shake. I don't think its the dreaded hop that everyone gets on these. I have 2 theories:
1. These cheap tires just suck and will never be right
2. The cheap junk Monroe shocks he put on are way too soft to do anything
so what do i do? Should i get some crazy shocks or will that make this truck even bouncier? Im worried about making it even stiffer than it already is.
View 12 Replies
I have a 2002 F250 with the 5.4 triton engine. Automatic transmission. When I reach 35 mph (sometimes sooner) the truck will shake horribly when I reach lower rpms. It will do this up to 65 mph and then it mostly stops. Completely taking my foot off the gas will stop the shaking, as well as shifting into neutral.
I know for sure that the truck has a cylinder 3 misfire as well as a minor exhaust leak, could either of these be causing it? Don't have the money to fix either of the problems for another couple weeks, is it safe to drive until then or should I play it safe?
View 2 Replies
I have an 04 6.0 F250. I am having a shaking between 1500 and 2500 RPM around 45 - 55 MPH. I have no guesses what is calling this, but the truck runs fine otherwise.
View 8 Replies
I have a 2008 F250 crew cab lariat 4x4 with 20 inch factory wheels that the steering wheel shakes during normal driving left to right. I bought this truck with 1500 miles on it. This shaking started at 50k miles and I was thinking it was a balance issue so I got new tires a month later since mine were about worn out anyways. They were factory replacement nitto terragrapplers. Shake was still there, swapped out for another set of nittos and shake still there, swapped to BFG AT KO's and shake better, but still there. I have gone through 10 or so balances, 5 roadforce balances, 2 alignments at 4 different shops including the ford dealer through the 3 sets. My wheels are scratched to hell and back from the careless people at the tire stores from so many balances.
My truck sat at the Ford dealer for a week just the other day and they changed the steering stabilizer. I thought it was gone, but a a few days later shaking started again. It almost feels as if every little bump, rut, crack in the road the steering wheel feels and shimmies (doesn't matter the speed, gets worse and more noticeable at higher speeds). The Ford Dealer says can't duplicate, but then when I go down there and test drive with them it's "oh yeah I see that, it shouldn't be doing that". The Ford Dealer says they can't find anything loose in the front end when I tell them to check tie rods, bearings, etc.
My truck has 62k miles on it now and it's driving me to the point of thinking about trading it on a Chevy. I love my truck, but it kills me everytime I make a payment and it rides like crap. I am still under extended warranty so I need to get this fixed before it goes out. I've also noticed that if I turn my steering wheel back and forth real quick while driving like warming up for a Nascar race I can feel a bumble in the steering wheel. This is NOT the death wobble as I use to get that around the 20k mile range and it disappeared and has never been back.
View 14 Replies
Well I just bought a 2011F250 6.7 on Friday. The truck has 42000 miles when I picked it up and now has almost 42800 4 days later. I love the truck so far. But anyways its an early build so is there anything I need to look out for? I noticed today I pulled into a parking spot and went to back up and as soon as I put it in reverse the truck shook pretty bad. It did it a few times as I sat there and went from drive to reverse. Is this something that is normal?
View 9 Replies
How to diagnose misfire with no CEL? 2001 F250 5.4. What could cause it?
View 13 Replies
I'll try not to post an entire book.. But I bought a 2000 F250 not even 8 months ago, it did have issues before but I changed out the spark plugs and coils and it fixed it's original missing issues.. I also just recently changed the fuel filter but it didn't fix it's new problem.. It drives ok around town but if I get over 35 mph it doesn't run well... If I try to keep a steady foot on the gas but don't get the RPMs over 2000, the RPMs will stay where they're at for just a second then they will drop down and the whole truck starts shaking.. I push more on the gas and it shakes even more and the RPMs don't move at all until I really step on it.. It lacks in power going up hills as well... The dealership i bought it from said the Catalytic Converter was bad but my uncle who is a mechanic says it isn't.. It's the first vehicle I've bought so kinda wanna make it last..
View 11 Replies
OK, quick question. I have an '03 250 with the 5.4 and the OD light began flashing tonight. I looked in the forums here and everyone say's new tranny or sensor but over on the diesel forums the are saying that the alternator is a big cause of this (dirty power).
At the beginning of this year I noticed what I assumed to be a misfire when putting the motor under a load. Once up to speed it would smooth out and all was good. I was told that a plug job on these trucks is hellish and expensive since a lot of guys break the plugs off in the block. I put it off and the issue went away when the weather warmed up.
Now it's getting cold again and the misfire is back. Driving home tonight the truck died at a light. I restarted it and as I accelerated I noticed a difference in the shift from first to second and then saw the OD light blinking.
Again, the diesel guys are all talking alternator so my question is this: could the alternator cause both the OD light to flash AND the misfire? If the "dirty power" can cause the tranny to fall in to safe mode, can it also cause the ignition to be problematic?
View 4 Replies
Have a 2007 F250 6.0 diesel with the standard issues including misfire at highway speed. Assume the bulletproof kit also cures the stiction problem? in reviewing the threads and looking at the vendors, references are made to fixing the oil cooler issue, egr issue, etc., but no one addresses stiction issue directly.
View 10 Replies
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
View 10 Replies
OK, not sure where to start so here goes. I have an 02' f-250 with the v-10. I just had some minor front end body work done and when I got it back I noticed that it just didn't feel right while driving. When I start it, I notice a small misfire while I stand next to the exhaust outlet. Nothing too bad, still runs great. Shortly thereafter I started noticing a more habitual missing while driving. Roughly between 30-40 mph and around 12-1500 rpm the truck feel like the driveline is about to pickle fork the truck. If I let off the gas or step on it, the vibration goes away. And very intermittent.
It will only do it when the truck is warmed up. If I only drive about a mile, it won't do it, yet if I turn around and head back, there it is! Now the weird part. I for reasons I won't get into, I left my ignition on and drained the battery. I just replaced it and for the last 2 days nothing. Nt even a misfire. Now today here it is again. I have read all over the forums for this exact problem and cannot find my exact problem. I have replaced the plugs with Autolites and cleaned the coils as well as the boots and applied a small amount of dielectric grease to the top of the plug. The boots are cleaned and not a sign of cracking or wear.
I replaced the PCV valve and nothing. All the plugs looked exactly the same. Light chocolate in color. Not one looked different than the other. I took them out again last week to verify the plugs weren't bad and the new ones all looked the same as well. I cleaned the MAF sensor also. Just cannot figure out what could be doing this all of the sudden. I don't see where anything wasn't plugged back together when it was being worked on and why would a new battery make it go away for a short time? Oh, and lastly, I have a superchips programmer that came with the truck and there are no codes showing and my check engine light has never came on yet.
View 6 Replies
Problem started with the front end shaking a little bit when braking like the rotors needed turning. Then the brakes began to intermittently hum when stopping. Then my ABS light came on. Put the truck up on the stands and disassembled the brakes on both sides. The ABS sensor was chewed up on the driver side. The less than year old hub felt sloppy so I changed it. Put everything back together.
New hub came with new ABS sensor. Went for a test drive ABS light is gone and I no longer shake or experience the hum when applying the brakes. However now when I go to stop right before I come to a complete stop the driver side (new hub/spindle side) I hear what sounds like the grade school class clown making a fart sound with his mouth, and the truck pulls to the driver side. Is the ABS system malfunctioning or is this a caliper issue? Calipers look like they are OEM.
View 3 Replies
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
View 9 Replies
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
View 3 Replies
I have a 2006 F250 5.4L. I was getting a noticeable misfire after not driving the truck for a while. Mode 6 revealed that cylinder #8 was misfiring.
I took off the coil/boot and there was coolant on the tip of the boot and some at the bottom of the spark plug well.
I cleaned everything up and put everything back together and that took care of that problem when I started the car. I also stuck a wad of paper towel by the intake manifold nearest spark plug number 8 and tightened the manifold bolts down a little. Some of them were not as tight as others.
I went back today and started the vehicle and it has the same problem again!
I took a look at the paper towel and it was totally dry! There is no coolant around the top of the spark plug well - only in the bottom of it. Where is this coolant even coming from? There are no coolant lines near cylinder #8. Is this a head gasket leak?
I have taken a look at the head gasket and that doesn't seem possible since the head gasket does not seal around the spark plug well at all as far as I can tell.
View 8 Replies
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
View 5 Replies
I have a 1999 F250 Super Duty 5.4L, 118,000miles...engine seems to idle somewhat rough but tach doesn't seem to move off 1000rpm & when giving slight acceleration seems to act like its missing, shaking . But under acceleration moderate or high purrs like a kitten! Always starts good , few cranks. Any hints on the what issue might be?
View 2 Replies
I have been reading several past post regarding the misfire while in OD and going up a small hill with light acceleration around 45 to 55 mph. Everything points to the COP so I replaced it today. Still getting the code after 20 minutes of driving around. My truck shudders and looses power. I can either let up on the throttle or hammer down on it to eventually smooth it out and everything goes back to normal.
Check engine light flashed but didn't stay on. My scanner does report misfire on cylinder 7 (P0307). Haven't owned this truck very long so I don't know much of it's history except OASIS report shows nothing alarming. Guess next step is a new set of plugs.
Another first today, is the tachometer is stuck at 4500 rpm. Shut the truck off and let it sit for an hour, then went back to start and tach. acts like 4500 is the new zero and running engine at 1000 rpm now indicates 5500. 2007 F250 SD 5.4 ....
View 14 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
06 250 5.4 40k on it, usually when cold and accelerating engine will misfire and stutter and then continue accelerating. The wrench light will flash sometimes but it wont store a code. This used to be vague in occurrence but has now started to be more a common occurrence even when up to normal operating temps.It seems only to misfire /stutter on hard acceleration or towing/hauling heavy loads. The only answer I got from a mech would be to do a computer reflash, not sure why /how this would fix whats going on.
View 1 Replies
