99 F250SD V10. There are two connections on the heater core at the firewall. Is there an 'inlet' and an 'outlet' or does it not matter? Put a cummins in the truck, the V10 has been out for a while and cant remember which one is which.
View 5 RepliesToday I noticed a leak at the heater hose assembly at the right rear of the engine compartment. It appears to have special connectors and that appears to be where the leak is coming from.
View 1 RepliesNeed the fuel system diagram or schematic for my truck.
1999 250 superduty v-10 Ser# 1FTNF20S1XEC67940
Every time I run it I smell gas. I changed the f/p 6mo ago. While I was working on it I noticed there was a hole rubbed in a small hose. I assumed it was a return line (smelled gas before too) and when I fixed it the smell went away until lately. I dropped the tank,yesterday and didn't see any problems. Just need to find out what hoses go where so I can replace the hoses??
I have put a new steering pump on my 2002 f250 and all new hydraulic hoses. I plan to install a steering pump filter on the system to protect it from anything that is not steering pump fluid.
There are two intake ports to the steering pump. One is near the bottom of the pump and takes fluid from the steering pump cooler after it has left the steering gear. The other intake port is near the top of the pump and takes fluid from the booster.
My question is - which hose would be better to put a steering pump filter on? Is there anything wrong with putting a filter on both? I imagine the first intake hose is constantly circulating fluid and the other only circulates it when the steering wheel is used.
My uncles 1999 v10 started to leak from the high-pressure hose on the gearbox. Replaced the hose which lasted for a short time but is now leaking at the same spot. The hose swivels, is this normal, seems like a dumb design for a pressure hose. Also is there a certain trick to doing this hose? He also insists on using PS fluid instead of the ATF it calls for. Could this cause a problem with the seal?
Edit: Also the truck has been lifted on 35s since 16k miles and its now roughly at 170k. He tows with it as it is his work truck. But the truck is well taken care of.
I bought a 99 f250 super duty with v-10. Ran great then I decided to hose off engine compartment. No pressure washer just running water trying to get all the dirt off now the engine sounds like its missing. Could I have a coil pack that got wet or is something else wrong.
View 3 RepliesI'm trying to troubleshoot a leak on my 08' F250 with a 6.4 powerstroke. It's been dripping coolant when cold pretty aggressively. Once the truck heats up, the coolant leak seems to mostly go away.
Here's a picture of the drip, it's marked by a dart, so you can see the location from the top (second pic). The radiator house connection around the engine seems dry.
Pic from Top ....
What's hidden here that could be causing the leak?
Where this small leak coming from. Under my radiator hose. Took a pic of the leak.
View 8 RepliesI've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
I got my 1999 f250 super duty v10 about a month ago. It had 200,700 some miles on it. It's now at 201,865. My issue is when I turn on my heater I smell coolant. It's kinda strong. No leaks that I can see. Not in the ground or in the cab or from what I can see of the heater core. It only smells when the heat is on, no smell on the cold setting. It sat for months before I bought it from a dealership. What it could be? Ok now it sounds like I have the ticking death sound. The one people have said happens when spark plugs are about to fail. So I guess new plugs are in order.
View 8 Replies2001 F250 5.4. The heater will blow warm air at idle and on the second highest setting, once you start moving or turn the fan up to full blast it instantly cools off. The coolant level is fine. The engine runs at a normal temp.The blend door does work. I just replaced the thermostat, and both hoses for the heater core are hot.
View 4 RepliesI recently replaced my heater core on 2001 F250. Would be a simple job if it weren't for the quick connects on the hoses. Any tool to take these apart on the truck where space is limited?
View 1 RepliesI bought the wife a truck a few weeks ago and she said the heater wasn't working well and was noisy. So I hoped in it at lunch today and she was right, barely any heat output and its noisy coming from behind the passenger airbag.
View 1 RepliesStarted to attempt to replace the heater core in my 08 SD 6.4. Didn't know the entire plenum has to come out in order to replace it. How to remove the plenum? My buddy is a Ford tech but I just am not getting what he is telling me and there is next to nothing coming up when I try to search.
View 2 RepliesSunday I bought a 2001 f250/5.4 to replace my 91 f250. I didnt drive it yesterday, but this morning on my drive to work the heater was very weak, it seemed to blow warm for the most part, but was barely pushing air even on high. I flipped it over to A/C to see if it blew any harder and it did. Does the blower motor need replace? if so why does the AC blow harder than the heater?
View 14 RepliesThe heater blows cold air from the driver side only. Very cold. Vey hot on passenger side.I have read that this is likely a blend door issue. Comments? Fluids are full. I hear slight noises from under the dash like "click click" like a door is trying to activate?? Truck out of warranty. If it is the door I heard the driver side is not as tough to install. Again comments? Instructions?
View 2 RepliesMy truck at idle sounds like it has aftermarket cams and the exhaust coming out of the tail pipe smells really rich. when driving down the road my heater controls default to defrost. Also when I fill up with gas it takes forever to get it to fill all the way. I am lost on where to begin with the problem [ I did check the tank vent hose and their is no blockage] Possible vacuum issue?
View 10 RepliesMy 2011 F-250 just started having a weird heater problem. My truck heater gets up to temp just fine but after cruising down the highway for about 15 minutes or so it starts blowing out cool air. I can turn the controls to defrost and back again and it blows warm, not hot but warm then cool again. It just started a couple of days ago. Temp gauges show normal temp also.
View 8 RepliesCold no start goes nowhere. I have a 2001 7.3 that will not start in the cold if I forget to plug it in....like last night. I have to plug in the block hater and give it a while before it will start. I tested the glow plug relay,it works fine. I can not find a test for the fuel bowl hear, and I'm not one to throw parts until I accidentally fix it. Any test procedure for the fuel bowl heater? Why this POS is so bad in the cold? Glow plugs tested fine at diesel shop in December, and this problem has been around since before that.
View 14 RepliesI have a 2006 f250 and the heater will blow cold air unless you are driving in like highway conditions. If you stop or drive slow it blows cold air only. What is causing this???
View 3 Replies3 different style chargers, with or without an actual load. if i rotate the charger, the radio goes in and out.
View 3 Replies