I have a 1999 f250 that runs and drives great but the only issue I have is when I baby the gas pedal it stalls a little and when I give it more gas it's fine or if. I'm going 50mph then let off gas and then baby the pedal it's stalls a little.
View 6 RepliesI just bought this 99 f250 7.3 Powerstroke last week.. drove it all week fine, I car pool with a family member to work and asked his girlfriend to plug my truck in for me, well she didn't and it had stalled on the way home one morning but started up after cranking a few times i thought nothing of it. Drove it a little bit that day and it was fine, while I let it idle in my drive way as I prepared to go work it started running really rough then died. It took a long time to start again..now it's happening all the time. I changed the fuel filter and someones telling me there's air in the lines..
View 5 Replies2014 F250 SuperDuty 6.2L gasser, x-cab long bed work truck. 105k miles, original owner, 1 driver, mostly highway miles, well maintained and super clean truck.
First issue occurred at 83k miles, Aug 2016. Warm summer day climbing I-70 in CO, slightly loaded, and just entered the Eisenhower tunnel (11,150' altitude). Lost power, no RPMs - not running, I put it in N and rolled as far as I could. Hazards on and no-where to pull over, hugging the wall and blocking one lane. Power OK - will crank, no fire. 1/3 tank on the fuel gauge and >100 miles distance to empty on the trip computer. Tunnel rescue shut down traffic and pushed me out into the daylight.
After waiting an hour to fill our paper work for disabling the interstate tunnel I returned to the truck which quickly started. No symptoms, no lights, no codes. Topped off the fuel tank after a easy 15 mile drive downhill. Drove another 800 miles symptom free to my destination and checked it in at the dealer. At this time a check engine light had finally illuminated - PO420. I shared the story of stalling out at highway speeds with the Service Writer. Dealer replaced the cats, confirmed fuel pressure OK, computer condition OK, serviced the trans (at my request).
No symptoms reoccurred during the next 20k miles until last weekend. 105k on the OD now. Heading to Flagstaff, AZ on I-40 in similar conditions. Hot, AC running, climbing in elevation, slightly loaded, running on the bottom 1/3 of the fuel tank... Died while cruising at 79 mph. Well, at least this time I wasn't in a tunnel and had a shoulder to pull off on. Deja-Vu - full power, radio on, no engine lights, gauges normal, fuel reads over 1/4 tank, >100 miles till empty on the trip computer - won't start. Cranks, but no fire. Some sputtering during start attempts must have triggered the next trouble code.
Opened the hood, removed the gas cap, let it vent and cool for about 30-40 mins while I took a walk. Returned to the truck which easily started and let me drive to the next fuel station, 30 miles away. This time the check engine light stayed illuminated. It took 24 gals of fuel. Drove 3 more hours and almost 200 miles without symptoms - check engine light still illuminated keeping me curious and fully alert along the way.
Got the codes pulled at a parts store that was open on Sunday. PO300 & PO301. Random misfires and cylinder 1 misfires. Sounds consistent with poor fuel supply? Spent the rest of the day searching forums for any clue to this highway stalling. All I came up with was to clear the computer - disconnect battery, turn lights on, wait 15 mins, reconnect battery, start engine, apply brake, drive, etc. This and another full tank of gas gave me enough courage to set out on my trip home.
Next occurrence was just outside of Santa Fe, NM. Similar conditions again: Hot day, AC kicking, Interstate travelling about 80mph, slightly loaded, climbing in elevation, fuel tank just below half - stalled out. Repeat previous learned routine. Open hood, vent gas cap, walk it off for 30 mins, return to truck, start it up. Drive to next town and top off with fuel about 30 miles away - only took 16 gals! Made it home 4 hours later without stopping. No repeat symptoms, no check engine lights.
The next day a code - PO420. Catalytic efficiency below threshold.
Quick recap:
6.2L gas engine stalling at hwy speeds.
Cruising between 65-80mph
-Interstate travel - no stops between last fillup and stall.
-Warm weather, AC on
-Running on bottom ~1/2 tank
-climbing in elevation, slightly loaded
To clarify: slightly loaded - no trailer, maybe 1,500 lbs bed cargo, mostly wind drag. The most I have pumped into the fuel tank is 29-30 gals or so. I assume I have the 34 or 35 gal tank. Never seen the calculated "distance to empty" below 40 miles.
I have a 2004 F250 with 5.4 Triton engine. It stalls when tapping on Power steering reservoir! This is the oddest thing I've ever seen! I did not get time to look into it today but will sure do so tomorrow.
View 2 RepliesI just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 RepliesI don't know whats up with my new truck, its a 04 f250 scsb, 4x4, 5.4l with 61k orig miles on it. Truck will stop on a dime, has NO pedal sinking, but it takes about 3/4 of the pedals travel to apply pressure to the pads and have the truck stop, sometimes if I push the pedal down then let up and push it again the pedal wont travel as far, I just flushed the system today, no air in the lines, is there a bleeder on the abs? truck has 4 wheel abs...
View 14 RepliesI have a 99 f250 sd truck that came as a auto and I am changing it to manual. I bought a slave cylinder unit setup and got it put in and as I was installing rod from pedal to slave I must of broke plastic fingers that hold rod. So is them fingers replaceable or must I buy another unit? with no foot on pedal it sticks up close to bottom of dash now. I tried pushing clutch all the way to floor and still rises too high. What can I do????
View 1 RepliesI have a 2002 f250 7.3 with a dead pedal and gauges. This has happened to me once before checked fuse 45 and it was blown. I didn't know that the po used a 30 amp fuse when it should have had a 15 amp. I replaced it with a 30 not knowing. Well coming home the other night it happened again gauges dead and pedal. Checked fuses all were good. Found this site and read about the cause in the shifter. Took that apart and fixed the wire that was broken in half. My question is what else is fried now from having a 30 amp fuse in while it was shorting out since I have no gauges and gas pedal.
2002 f250 banks six gun
banks 4 inch exhaust
The truck in my sig. makes a clicking noise when it's in the park and I press the brake pedal down. The click is coming from somewhere up high in the steering column. It doesn't make the clicking noise in any other gear only in park. Might be normal but I don't remember hearing it before?
View 9 RepliesPulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesI have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 RepliesI have a 2000 F-250 Diesel that has started acting strangely. It starts and runs well, but every once in a while the peddle just stops working. Might be a second or so and then the RPM will go up. Or you may be running down the road and all of the sudden it just stops acting like it is getting enough fuel. Same thing it might last a second or so. Sometimes it might happen 4-5 times in a row over a few minutes and might not happen again for a day. Truck does not stall when this happens. It just does not go like it should.
View 1 RepliesI just recently purchased my 1999 ford F-250 superduty V8 5.4 5 speed with 144,00 miles and I'm having a issue with the clutch pedal sticking in and then it will pop out after a couple seconds. It will stick more when I come to a light and have my foot on the clutch but the pickup drives fine and there is no slipping of the clutch. I have never experienced this issue before in any rig I've owned. so I'm a little lost at the moment.
View 2 RepliesI've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
I noticed last week that my brake pedal seemed more spongy than usual. The next day the pedal would go down about half way to the floor before I had pressure. And then the next day the pedal would go straight to the floor. Pedal comes back up once released. I still have brakes pressure about an inch before the pedal bottoms out. Its been like this a couple days now. The vaccum pump works fine. I'm gunna try bleeding the brakes on it tomorrow.
View 5 RepliesI took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
2008 F250 Crew Cab 5.4, 79K miles, had new brake pads installed at 40K miles. Recently, I noticed front end shudder and some pedal pulsation while braking. It started kind of sudden. My first thought was a warped rotor.
When I took things apart, I found passenger side front rotor was cracked and the caliper pistons were rusted and falling apart, the old pads were only worn about half way. My thoughts on a bad rotor were confirmed, and then some.
I replaced the broken caliper, both front rotors, installed new pads on all four wheels, and bled the brakes. To my surprise, the brake shuddering did not go away. I'm stumped.
I have a 99 F250 7.3PSD; I upgraded the tranny cooler after an episode of overheating while backing up a hill.
The truck has done well, hauled a few tractors with it, but recently I have noticed something that seems scary. When going downhill, I often relax on the accelerator. Usually there is some passive engine braking as happens with any auto tranny. Recently, the truck just coasts - it is as if you feel the tranny shift into neutral and you just coast, except I didn't shift. While this is happening, the accelerator pedal will not rev the engine. You can put the pedal all the way down -> rpms at about 6-800. No response.
At the bottom of the hill (so far) the engine gets louder. the rpms drop, and the accelerator works again. Every time, so far. But, if IO am going down hill, and want to accelerate to execute a laneg change or something - I can't. AFAIK, everything A-OK after the new tranny cooler. levels, etc.
I'm having issue with my brake lights. Checked for voltage and nothing. Checked the fuses under the dash. Checked the brake pedal switch and have power going out when the pedal is pressed. Is there a relay or something somewhere else? 1999 f250 7.3 superduty....
View 2 Replies