Ford Super Duty (1999-2016) :: F250 - AC Compressor Front Plate Rattling
May 28, 2015
1999 F250 SD 5.4 with 140k miles. There is a triangular plate with a bolt in the center and and what looks like a bolt in each corner of the plate.
Two of three bolts in the plate are missing and the third is loose allowing the plate to spin freely. Center bolt is tight.
Gotten to the point it's really noisy. Can the bolts be replaced in the plate or should I just go ahead and replace compressor. If bolts are replaceable what size?
View 6 Replies
Advertisement
I guess my AC Compressor is about to the bed. AC works good however there is a lot of rattling going on. Been driving it like that for two months plus expecting it to fail.
Just not sure how long I should let it go. If the compressor pully fails on the road I will lose my serpentine belt and the ability to put the spare on and I will be stuck for sure.
2008 F250 XL 5.4L .....
View 1 Replies
I have a 2003 F-250 6.0L 2WD and I recently noticed a rattling thumping noise under the front end on the passenger side. I noticed the rattle shortly after I got new tires, which are a hair bigger than the tires I had on it before. I thought it might be my new tires rubbing since they were bigger but then I noticed the rattle when I had my wheel straight and also when not moving at all. I've been driving it for a couple of weeks now with this rattle and I've been able to determine that it rattles most when I am going downhill and turning to the left putting more of the weight of the truck on the front right suspension components.
After reading several threads my first attempt to find the problem lead me to the discovery of a worn sway bar bushing. I thought this was for sure the problem and replaced both bushings and end links. But the rattle didn't go away. Then I thought maybe it was a bad wheel bearing so I replaced the wheel bearings in both front wheels. Still no change. Lastly, I happened to find a loose ABS line in the front right wheel well that was no longer secured and was banging against plastic. I secured that and still no change. All the bushings seem to be in good shape so I am considering taking it to a mechanic since I don't want to just replace everything hoping that it solves the problem piece by piece.
View 12 Replies
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
2004 F-250 FX4 SB 5.4 V8 140k
Issue: rattling/clicking noise from passenger front wheel area at speeds lower than 15MPH, made worse under light braking and/or turns to the right.
Clicking sound is speed dependant.
Spindle? Hub? Balljoint? Sway joint? Rotor Issue?
View 14 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
Got a 06 F250 V8 Gas. Went to turn AC on the other week & got warm air out vents. Put 1 can of 134 in & the gauge on the "kit" said it was in the green. It was working last summer. You can turn the compressor "face" so it's not locked up, but it's not kicking in. Swapped the replay with another one & the 10a fuse in the fusebox under the steering wheel is good. Is that the only ones? I find it hard to believe that it's something serious. We did change the belt a few weeks ago & I was hoping that we had pulled a wire loose. The vacuum line that plugs into the heater hoses is plugged in.
View 14 Replies
I have an 06 f250 6.0 when I'm driving and let off the throttle and coast I hear a rattling sound like a spray paint can being shaked sounds like its coming from engine compartment.
View 6 Replies
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
View 7 Replies
This must have been asked before but I couldn't find any thread about it. Have a 2006 F350 that makes a rattling sound when engaged in front wheel drive. Sounds a bit like a loose ball from a ball bearing (or a small stone) rolling around. What might be causing this?
View 3 Replies
I trying to find the distance/length of a 2005 4x4 onward front radius arm. I'm fitting a 2004 Cummins nv5600 and transfer case into a 1997 fzj80 Landcruiser. I'm also fitting front and rear diff/axles from a 2008 f350 however don't have the radius arms and late model f250 are extremely rare birds here as Ford don't sell them here. I want the distance from the rear bush in the radius arm(at the chassis) to the front bush (top and bottom) at the diff/axle....
View 1 Replies
I bent my front bumper. Every time I look on amazon or ebay , when I put in my year, model, engine, it says their bumper won't fit. Mine has the 3 rectangular openings, 2 have the holes for mounting and tow hooks. It is chrome with the gray plastic or rubber bottom.Xlt. Also what part is the valance?
View 7 Replies
I am looking at a set of SD axles for my 92 F250. I have been looking for the last 2hrs and have found measurements for seemingly every axle in existence except for the SD D50/60.
What the center to center width is on the spring pads of the front axle. Wouldn't hurt to know the same measurement for the rear either.
Also, a bit more trivial, but still need to know, what is the size and taper of the draglink joint that goes in the pittman arm.
View 3 Replies
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 Replies
I recently purchased a 2002 F250 Regular cab long bed 2wd. I'm tired of the front end sagging so low, so I've been looking into a leveling kit. I was wondering whether I should go with 2" or 1.5" for the kit. I tow about 2000 lbs. 3-4 days a week and do not want the truck to look like it is squatting too badly. However, I really would like it too look more level.
View 8 Replies
I just bought a used 2013 F-250 4x4 and it came with the snow plow pkg. heavy duty front springs. I love the truck, but won't be plowing with it, and I don't need the rough ride (and don't like the look of the front end higher than the rear)
How hard is it to swap out the front coil springs and replace them with the "regular" ones?
View 7 Replies
I got a 2014 F250 SD w/ 6.7 diesel. Since if owned the truck the front bumper has slowly started to sag at both driver and passenger side. Dealer says there is no adjustments for it.
View 14 Replies
I have a 2010 F250 with 154000km (96000 miles) that we bought last week. When I was looking it over during the purchase I noticed the front axle didn't lockup in "auto", in manual lock it seemed fine so I figured vacuum leak or something like that. Yesterday morning I was in the yard and got a little hung up in snow drifts so just got out, locked the hubs and switched to 4x4 and I think the front end didn't engage at all.
So later on I had it in the shop installing the two way radio and decided to check the front end out a little more thoroughly. Vacuum lines seem fine, hubs turn fine but I notice the axle shafts both move up and down almost a quarter inch, that seems excessively loose to me. I've been doing some research on the internet and it appears the front hubs are serviced as a unit, also some information seems to point to needle bearings within the actual locking hub mechanism itself?
So the questions:
1. Does that front axle shaft seem excessive? What are the specs?
2. Can I replace bearings and seals only or do these units come only as assemblies? Inner hub, outer hub units? Wheel bearings seem fine.
3. With that much play is there a chance the outer axle shafts are worn also?
View 14 Replies
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 Replies
In the last few hundred miles of driving, I notice there is a strange noise coming from what appears to be the front end of my truck. It sounds similar to a buzzsaw or a power sanding tool whenever it comes in contact with an object. The noise starts at around 30 mph, stops from 55-60mph, and starts again around 65 mph. The truck rides and drives normally and there doesn't seem to be any metal to metal contact noises or clunking and the hubs dont seem to be hot to the touch. I was thinking improperly balanced tires, wheel bearing, or front carrier assembly. What it could be? The noise just suddenly started and I was wondering if I should keep driving it?
View 7 Replies
2003 F250 4x4 7.3L
While doing my brakes in the front, I tried to wiggle the front left, nothing. Solid. Then when I did the right, I was surprised to see it wiggle when I grabbed the tire. So I looked to see what was moving.
Not the U joint, not the ball joints, But it looks like what is a drive shaft.. (I am new to this stuff). On the right side a shaft comes out of the axle just before the U joint and the rest of the wheel assy. What is wrong?
View 6 Replies
