Ford Super Duty (1999-2016) :: F250 4x4 V10 - Intermittent No Start / Complete Stall While Driving
May 24, 2016
1999 F250 SD Ex 4x4 V10 has been intermittently not starting, both cold and warm, began last fall but only happened once a month or so or longer. Would then start after trying again either right away or after waiting a bit. Now it is doing it on a regular basis. Sometimes it will start right away, sometimes won't but if you keep trying or wait awhile it starts, sometimes using the extra key will start it right away after the first one didn't, sometimes neither one. It does not try to turn over, make any noises, no warning lights flashing, just won't start.
Now also on two occasions within the past week, it just stopped while driving. Radio, dash lights, etc., stayed on. I got it to the side of the road with the little power steering left where it started up again right away.
No codes showed up. First mechanic couldn't find anything obvious or replicate problem. Changed air and fuel filters (fuel filter really needed changed), plugs. Got truck back and it wouldn't start next morning. He checked it again and got a code related to ignition, tried the spare key and it started up. Truck back home, next day same problem.
Mechanic 2 checked, no codes, kept several days but, of course, couldn't replicate problem. I'm not even sure what all they checked, used to be an excellent repair place but now they seem to only really on diagnostics and throw up their hands, very disappointing. Replaced solenoid and starter last year myself. Otherwise, have had no problems until this.
View 7 Replies
Advertisement
I've been having an intermittent stall-out problem with my 2003 F250 5.4L (160k miles). The truck has been retired from DD to farm duty, hauling, and towing only. Over the past 9 months, the truck has stalled-out on me 3x while driving. I will be driving along sometimes at highway speed, sometime slower, and everything will die: no PS, lights go on all over the dashboard. It will not restart right away. I have to wait at least 20-30min to restart it and then everything is fine for several weeks and hundreds of miles.
There are no codes and I have been unable for reproduce it/cause it to happen purposely. My mechanic has changed the Crankshaft Position Sensor, and checked the fuel rail pressures. I also checked all the harnesses and fuses, cleaned the battery terminals, looked for vacuum leaks, and gave it a good look-over. The following are new: battery, IAC valve, fuel filter. After searching the forum I also pulled the fuse box and examined the integral fuel pump relay: it and the board looked perfect, no bulges, cracks, discoloration, etc.
My mechanic thinks this is more likely an ignition problem than a fuel delivery problem.
View 4 Replies
Have an 06 F250. When I slow down to make a turn then accelerate it's like the drive shaft spins half a turn before it catches. Been doing it for awhile now. Now I'm get a clunk when I come to a complete stop. When you stop then truck settles there is a little clunk. Does this sound like the slip yoke problem?
View 1 Replies
2016 F250 6.7L 4x4
I getting some tranny noise when towing on incline from a complete stop. When I slowly press the gas pedal I hear grinding noise. If i press the gas more my truck starts to move and the noise goes away. It doesnt happen all the time. This started right after my 1000 miles recommended break in before towing per ford manual.
My truck now has 2800 miles and the grinding noise occurs intermediately regular driving. Mostly on steep incline or decline. I haven't taken it to the dealer yet because I cant recreate the issue all the time.
View 6 Replies
I have a 2000 f250 superduty gas v10 6.8L . I bought this truck about 4 months ago. Now when I take off from a complete stop the truck shakes up until second gear, shifts fine all the way up until the last gear it looses power "loosing power" i mean i can put my foot into the pedal and it takes forever to climb speed meanwhile the RPM'S never skyrocket like it the transmission was slipping if anything a couple times the RPM's dropped are stayed the same then as i take my foot off of the pedal once i have my desired speed sometimes not always the truck will give me a little jerk Also Just the other day I was driving on the highway and decide to put her on cruise control at about 70mph, I set the cruise control and the RPM gauge was just over 2,000 and the tach was fluctuating up and down about 1/16 of an inch. I been reading alot of forums and what I got out of them is it maybe pointing me to a misfire maybe the coil packs? Plugs?It's not something major like a transmission rebuilt.
View 6 Replies
New issue I've discovered , when stopping , the RPM's drop down to 500, truck acts like it wants to stall , then goes up to 750 RPM's . Then it's fine . Doesn't hesitate when accelerating . Idles slightly rough after start up , about 30 seconds . I've checked the air filter , cleaned the IAC and MAF. Fuel filter is only a year old . What I should check next ?
View 14 Replies
250 2006 Superduty v10. Codes p2106 and p2135 ... Only occasionally when coming to a stop it shudders like it would stall. It happens for just a few seconds then ok again but wrench light comes on. After the next shut off and start the light goes out. I had the throttle control position sensor checked and they said it was ok. Got a software update at Ford. I hate to just start replacing expensive parts. I have about 60000 miles and it is a great truck otherwise.
View 1 Replies
I have a 2006 Ford F-250 5.4l the symptoms are when it's warm it has half power and it will stall at idle. What I have done with the truck is.
New cam phasers
new chain
new tensioners
new vct solenoids
new oil pump
new plugs
new ignition coils
new stock cam shafts
new rockers
new lash adjusters
new exhaust manifolds both sides
new muffler
oil change with the right oil
ran it with sea foam in the crankcase before oil change
new fuel pump module
new evap vent control
new abs speed sensor
I cleaned throttle body with brake cleaner ... Scanned it after a 15 min ride of having to use 2 feet to drive it. The engine codes that came up are p0022 iacv short to ground and p1000 readiness test not complete. I also got p1804 4 wheel drive high indicator circuit failure p1808 4 wheel drive low indicator circuit failure .... Not sure what else to try.
View 7 Replies
While driving up hill at 60mph the truck lost power. Rpm jumped up as to change gears as it hit 55mph. Still losing power until it shut off. I tried to restart and just got a click from the solenoid. No engine codes whatsoever. Battery had 12.1 volts but when turning the key to start in getting 8 volts. Had it towed home. Today I swapped batteries with my other truck and same click noise from solenoid. All lights, radio, ect still work. Where should I start? Alternator, fuses...?? 2008 f250 5.4 ...
View 12 Replies
So I'll be driving down the road and the gauges will randomly start jumping around then the truck will just shut off, this just started a couple days ago, it seems to be gaining in frequency, when i try and restart the engine all my warning lights flash on and nothing happens, try again and it starts back up, now the last time it happened all of the above happened but it was followed by a fast clicking noise from under the steering column, it has to be a electrical issue as i have full tanks and motor is in tip top shape. Also no codes pop up with my code reader.
View 1 Replies
My 2002 F250 7.3 randomly dies while driving and seems to only be when I hit a bump no matter the size. I have checked the valve cover harness connector outside of the valve covers and they look fine. I checked the ECM connection took it off and reconnected it.
Changed the CPS censor twice, checked the ICP sensor, checked continuity of all the glow plugs through the valve cover harness. Checked the fuel pump, checked all related fuses, changed the fuel filter, checked glow plug relay, batteries hold good voltage and were recently upgraded to bigger batteries.
Engine runs just a little rough but not enough to be of concern. Air filter is clean and oil level is perfect. What could possible be causing my truck to randomly die when it hits a bump and not start back right away??? This truck is new to me and its the first diesel engine I have ever owned.
View 13 Replies
My 2001 6.8 L V10 runs great all day & night without issue, but first thing in the morning when below freezing it has a hiccup. It'll fire right up and stutter and stall within less than 2 seconds. Usually twice. Third time it fires and keep running. Is there a fuel check valve somewhere on this thing? Not sure what that would have to do with the temps. Wondering if it's/there's an easy fix or not?
View 5 Replies
I have a 2006 f250 lariat 192k no mods except k&n filter everything is stock. I have 2" pro comp level kit and a scan gauge 2 nothing fancy! Well the other day I noticed my truck was chirping like a Chirp chirp chirp...... Chirp chirp...... Chirp chirp chirp! It goes up and down with the rpm's but it's comes on and off only when the engine is up to running temps the belt does squeak during warm up but I don't think that's it, it's coming from the back of the engine I'm sure of it because I used a paper towel tube and listed right in the turbo hpop area on top of the engine but it's too hard to tell I can't find exactly where it's coming from, some people I've had listen think it's a belt or pulley or tensioner! But I'm not sure if it is because I've sprayed water, and wd40 on the belt and pulleys with no change!!! I'm afraid it's a lifter or something inside the engine yet it's too loud and pronounced to sound like it's coming from the inside! I'm just lost!
View 8 Replies
For about 6 months the cruise control on our '09 F-250 has been intermittently failing. One time I'll set it and it will work fine, the next time I try to set it and it fails. No particular rhyme or reason to when it fails to set.
Some of the tests that I did indicated it was the brake light switch on the brake pedal arm. It seemed to work perfectly a few times that I drove it after the installation but now it's back to working when it wants to.
I had a problem with the cruise on our '06 Ranger and it turned out to be the module. It acted a bit the same way in that it would set sometimes, other time not. I don't know if the two systems are similar or not.
View 6 Replies
The tach in my 01 F250 PSD has become intermittent. It works properly some of the time, not at all some of the time, and jumps up and down some of the time.
Does it get it's signal from the CPS? It has a blue CPS that's about a year old and the truck runs fine?
View 6 Replies
I have a 1999 f250 super duty with the 5.4 Triton motor with a 5 speed. I bought the truck a couple months ago, and it had a bad manifold leak (not surprised lol). but it ran fine just noisy. So i had a shop do new gaskets and bolts. Then my problems started.........
When you start up the truck she runs fine and some times drives fine. I will be driving along and its like some one hits a switch and i suddenly loose all power it spits and sputters and i have to down shift to make any kind of hill.
So I figures I had a misfire i got a light on for cylinder 5. So I decided to change all coils and plugs hoping that would clear things up...... well it didn't. It ran great for roughly 15 miles then it started to do the same thing again. I've changed air filter and fuel filter also.
When it starts sputtering i sometimes get a check engine light on and then it goes away. when the light is on the codes are:
P1151 A Heated Exhaust Oxygen (HO2S) sensor indicating lean at the end of a test is trying to correct for an over-rich condition. The test fails when the fuel control system no longer detects switching for a calibrated amount of time.
Read more at: [URL] ....
P1152 Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Rich Bank 2
Read more: P1152 FORD Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Rich Bank 2 | AutoCodes
Both codes come on together always. but it will go away when the sputtering clears up. I just checked fuel pressure its at 32psi at a idle.
View 1 Replies
I have a 2002 F-250 7.3. I was driving home from work on Tuesday (highway), I heard an intermittent noise coming from the front end, sounded like a rubbing/grinding noise. Yesterday on my way to wok, same thing, on and off. Yesterday on my way home the noise was constant, didn't go away. The noise comes at about 45mph and stays until I'm back under about 45mph, so mainly just on the highway. I put the truck in neutral and let off the pedal and the noise is still there which tells me it isn't engine related.
Yesterday after work I jacked up the front end, spun the tires, no noise. No play in the tires top/bottom or side/side. Took the tires off and what I did notice is the right axle u-joint is shot. I am hearing the noise in 2wd so I don't know if its the u-joint that's making the noise. Could it be a bad wheel hub bearing? Is it the u-joint? Maybe needle bearing??
View 6 Replies
My 2014 F-250 is having a repeat problem with an intermittent cell engine light. About 10000 miles ago it happened, and they changed out the egr cooler. Saying it was gummed up with soot. Problem just started up again. Light will stay on for about 3 or 4 restarts then sir off on its own. It's this a known issue with the 6.7? Is there a way to prevent it?
View 7 Replies
I've got an intermittent Trailer Wiring Error message that started appearing with a trailer connected on my '11 F250.
Brakes and lights work OK on the trailer, I thought I had read on the board here that there was a TSB for this, but I cannot find it.
View 10 Replies
My truck is a 2003 f250 / 2wd automatic, 7.3 powerstroke, 284000 well maintained miles.
Just last week I sprug a large oil leak and had to replace the hoop outlet o rings..problem solved. This week I can drive 15-20 miles on the freeway and the truck starts to act like ota running out of fuel. Bogs down to 40mph then starts missing. I pull over, and when revving I have un burnt fuel and oil smoking out of my tailpipe. I let it sit for 5-10 minutes and it will be fine for the rest of the drive and this happens intermittently, there is no pattern.
The truck has a ton of power, starts great hot or cold. I did a ton of research and found a IPR could possibly cause this, as could plugged screens in the fuel pickup. Then I read about all the injector harness issues but I don't think that I my issue.
View 8 Replies
As a follow up to my problem of intermittent stall and hard start, it is getting more pronounced. Now, every once in a while, it will start. Mostly it will not start.
This morning I connected an OBD2 meter with the key on and engine off. It told me that there are no DTC's. As I was attempting to run enhanced DTC's the code reader lost link with the computer. The connection icon was on but it lost the link. At one point, after several tries, I got the link back but it didn't last too long before it was lost again.
This is the same symptom that I have with running the engine. It will run and then shut off. After a hard start, it will start and run just fine and then shut off again.
My question is this. Can I still have power to the PCM and loose power to the processor? Is there a fuse or relay that could be causing this problem? If not, could the problem be a faulty PCM.
View 3 Replies
