Ford Super Duty (1999-2016) :: Excursion Won't Start After Changing Shift Tube
Jan 31, 2016
I changed the shift tube in my Excursion today. I'm trying to put the key switch back in. It will go in and rotate fairly hard. I can not get the key to release. When I hook the battery back up, everything functions as it should but it won't start, the key won't release and it still turns hard. The dash lights come on and such when the key is turned to run. I tried a different key with the same results. Everything looks good.
View 1 Replies
Advertisement
I have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 Replies
I'm in the process of changing my shift motor on my 04 f350. I can't get it off because of a broken bolt. The previous owner must have done this before, and snapped the head and some of the shaft off, so it's basically an alignment pin that's recessed into the hole on the motor. For some reason it's holding the motor on, even though I don't think the hole is threaded. Any way to get it off. I'm thinking that taking a MAP gas torch to the casting on the motor may be my best bet.
View 8 Replies
Last night was changing front driver's side shock on my 2011 F250 PSD. Right front wheel still on ground and needed to turn wheel to right to better access shock mount. Started truck and turned the wheel all the way to the right and took the key out thinking the wheel would lock and I could change the shock easier. But the wheel didn't lock and actually spun itself almost a full turn after I took the key out...I'm assuming because the right wheel was still on the ground providing resistance, but I think the wheel lock may have broken.
Finished the shock and went to start, but nothing. Everything is clicking and buzzing like normal but wouldn't turn over. Checked all fuses that seemed pertinent but none were bad. Wasn't able to check any relays. Gave up and was going to have it towed.
Son and I had to straighten the wheel so I could roll in down the driveway and the dang thing started after the wheel was straight! Thought it was a fluke and parked it. This morning did the same thing so I cranked the wheel to the right and it started again. Now at work and thought I better check again and I can't get it to start for anything. The steering wheel lock seems to be busted and now I'm thinking it could be something in the steering column, but this is a little above my pay grade.
Need to get home tonight and was hoping my description would be enough to make a for sure diagnosis. Otherwise its getting towed to the shop and I'd rather fix it myself if i can.
So went back out and tried starting in neutral again, but this time fiddled with the shifter while turning the key...nothing again. Ran it up into park and tried it again and it started! Last night and this morning I didn't mess at all with the shifter, just manually turned the wheel with the engine off. This is the first time moving the shifter worked and I didn't turn the wheel at all this last time.
View 6 Replies
The dipstick tube on my 5.4 snap and ive ordered a new one. it looks like it may not be to hard to replace.
View 4 Replies
2010 F250, what size tube do I need to fit on the brake bleeder screw? The tubes I have are all too big and the size marks are no longer legible.
View 4 Replies
Today I put a new shifter tube in a 02 f450. Everything works well, but the key won't come out and the steering wheel won't lock. Was told there is a button to push by the turn signal side but don't see any. Looked around top and bottom of column and didn't see anything out of place. Also found a black wire with a pink strip not connected to anything. Touched the wire to the column and key dinger sounded. Where should this wire be connected?
View 10 Replies
OK, so I have a 01 f350sd and i went to check my oil and the dipstick tube itself is so rusted it snapped in half so I took it to the dealer which I knew was going to be over priced labor but still checked the tube itself is 20 dollars but labor is upwards of 300-500... My engine is the 5.4 triton.
View 2 Replies
I think the gear shift lever is loose and so I get a no start every day or two. I remembered seeing somewhere here that there was a way to tighten up the grearshift lever to fix this problem. I did a search to no avail.
View 5 Replies
I just finished putting a 7.3 back in one of our f450 plow trucks today, so then i moved onto our 2001 F250 5.4 plow truck. The dipstick tube was rusted in half so i pulled on the remaining half to get it out and put in the new dipstick. However, it broke off at the block. So now i cannot see how to get the rest out with out doing a lot more work. I haven't removed the splash guard yet but will i have to remove the manifold , the oil filter base, or both?
View 14 Replies
Today I put a new shifter tube in a 02 f450. Everything works well, but the key won't come out and the steering wheel won't lock. Was told there is a button to push by the turn signal side but don't see any. Looked around top and bottom of column and didn't see anything out of place. Also found a black wire with a pink strip not connected to anything. Touched the wire to the column and key dinger sounded. Where should this wire be connected?
View 14 Replies
My a/c vents smells musty/moldy when A/C is turned on, searched the FTE site and everyone says to check the A/C drain tube to make sure it is not clogged, I have searched all over top and bottom with a flashlight for the drain tube and swear there isn't one. I think it should be on the bottom of the condenser box but just do not see it. Where it is located? The vent smell is Awful!
2000 F350 Super Cab 7.3 Diesel
View 6 Replies
I have a 2011 F350 diesel 6.7l. I have had this smell outside the front of the vehicle for months and so I took it finally to a dealer to solve the leak problem. They spent hours on it and eventually found a leak in a tube at the rear of the engine under the intake manifold and supposedly solved my problem. That was 2 weeks ago and I have driven about 300km.(180 miles) but the smell is still noticeable. How long should I wait before it goes away or should I return it to the dealer for further work?
View 6 Replies
I have a 01 Ford excursion 7.3 auto and it will not start unless you jump the starter relay, I have replaced the starter, starter relay and swapped out batteries from my 2000 F250 auto, not sure what to do and this is my daily driver. Not sure if this matters but just had the transmission rebuilt. I have tried searching other threads but still not finding what I need. Once it starts it runs and drives. When you turn the key you hear a click like a relay is engaging and all of the lights and gauges work it just won't start with the key.
View 2 Replies
I have a leak where my heater core tube goes into the intake at the rear pass side of engine. I have read that this part is pressed in. I dont want to remove the intake since i just paid $400 to have a new gasket kit put on. My question is can I bypass this tube with a hose from the water pump like in this video?
FORD 4.6 , 5.4 , 6.8, HEATER HOSE UNDER INTAKE REPLACEMENT THE EASY WAY !!! - YouTube....
If I can do a rubber hose like in the video I was to make sure that the tube just goes through the intake and that it does not supple coolant into the intake??
View 13 Replies
My 2011 f250 has 92k miles, I want to change all 16 spark plugs.
Do the 6.2l plugs have problems breaking like the 3v engines did?
I think I'm going to pull the passenger fender liner to get to the lower plugs in the head.
How does the coil pigtail unclip? I looked at them briefly earlier and it looks like you pull the red tab back, then press down and pull on the pigtail but that did not work and I did not want to break anything.
View 14 Replies
I have erratic changing of directions of the air control. It'll be on ac it will then change to feet or defrost. then stay on that for a while and flip again. It'll then stay on that one( usually vents). I'm guessing the selector switch or the vacuum egr valve.
View 1 Replies
I have now found a chit load of LED fog bulbs in my search. I don't want to change out the entire light, just the bulbs. How do the bulbs effect the side vision. Almost hit a deer a couple of nights ago with my F350.....don't want that
View 8 Replies
Just did my first oil change on my 2015 Super Duty 6.2 engine. I got the Fram filter the book called for, a PH-2. There's goobs of room for the longer filter. Would that be the PH8A? The book is about to trying to figure the comparable long vs short filter. Why do they insist on those short filters when a full size will fit? My Dodge Ram Hemi was the same way.
View 14 Replies
Actually a couple of questions. I've had one oil change in my F250 6.7. Getting close to the second one. So, my question is, what is the computer using to decide when to tell you that you should change the oil? And, if you changed to a synthetic oil, could you go longer between changes? And, if so, would the truck's sensors be able to tell the difference in the type of oil being used?
View 4 Replies
I need to change the fuel filters on my 2014 F250 with a 6.7L. Are there any special tools required and any tips on how to get this done?
View 7 Replies
