Ford Super Duty (1999-2016) :: Conversion Of Leaf Spring To Coil Spring?
Jan 17, 2013
Conversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
View 10 Replies
Advertisement
Where I can get or have a speed nut for the front eye bolt of the right rear leaf spring? If you do I'll gladly send you some cash for it and to cover shipping it. It's supposed to rain pretty much all week here and I really don't want to go to a junkyard. I have checked ford parts and nothing there you can get the hanger that attaches to the frame that the spring bolts to but not the speed nut or bolt only need the speed nut though. Truck is an 2004 f-250 so 1999-04 will work and 05 to 07 is setup the same in the rear but I don't know if they are the same size bolt since they made the frame heavier. I have no idea after 07 when they made the springs longer.
View 1 Replies
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 Replies
My front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 Replies
What is the width between the spring perches on leaf sprung 99-04 front axle. I searched and cant seem to find a dimension listed anywhere. i tried the dana60 bible on the pirate site as well, but it doesn't list the spring perch dimensions, only for the pre 99 styles
View 2 Replies
Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.
View 3 Replies
So I went to install a front end leveling kit in my 2003 2WD F250, looked like a simple task, except the bolt that holds the lower coil spring mount won't budge! I tried heating the nut, I soaked it with WD-40, tried a 200lb impact and a 30" breaker bar with all my weight. Is there something I am missing?
View 5 Replies
Any success story on converting 2003 or 2004 f350 with leaf spring front end to the 2005-2007 f350 coil front end is it possible?
View 8 Replies
I am looking at a set of SD axles for my 92 F250. I have been looking for the last 2hrs and have found measurements for seemingly every axle in existence except for the SD D50/60.
What the center to center width is on the spring pads of the front axle. Wouldn't hurt to know the same measurement for the rear either.
Also, a bit more trivial, but still need to know, what is the size and taper of the draglink joint that goes in the pittman arm.
View 3 Replies
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 Replies
2001 F250, 5.4, Replaced the clockspring and now my steering wheel feels very tight. After cornering, it doesn't come back on it's own, like something is rubbing. The face of the clockspring is slightly different than what was there.
View 1 Replies
I have a ford f350 2014 that had some water damage, the clockspring suffered water damage so I replaced it along with the steering column module.
The clockspring was brand new from ford, already centered, I pulled out the plastic tab during install.
Cluster has SERVICE ADVANCETRAC error and IDS is shows fault with the steering angle sensor. (see picture)
Do these new sensors have to be reset and calibrated to work, or does this FAULT message on IDS indicate a wiring problem?
View 6 Replies
I have a 1991 f250 that used to have a camper on it, I recently got this truck and when I put an older heavy camper on it the back springs flattened out and the front raised about an inch or two.
My question is...I am going to put air bags on this truck to alleviate this problem, should I replace the springs as well or will the air bags be sufficient to handle a camper?
View 1 Replies
2003 F250 7.3... I noticed a water leak dripping down onto passenger side front leaf spring. I saw this before but attributed it to the AC (which kicks butt) but haven't used the AC. No scent to the clear fluid, temps all look good. Running fine. Where does the AC discharge go? Could AC be on (not on AC but set in blue zone on dial)? Reservoir looks ok but could e small volume of drips.
View 12 Replies
My 18 year old launched the little wire spring thing that applies pressure for the brake pads on front disc brakes. Could have gone in to neighbor's yard! Actually lost one on each side. He put it all back together without one on each side. I said it would still work fine. What's the deal really? Can't be that important are they?
View 14 Replies
The local shop here suggested getting a set of F350 springs and they would take them apart and a leaf to the front and rear springs.
View 2 Replies
So there I was doing a simple oil change and when I took the filter out I noticed the little spring on top, in the center of the big spring (oil filter adapter) cocked to the side with the little plastic piece broken.
does anybody know if I can replace just the oil filter adapter (spring thingy that goes in the middle of the filter when installed) or do I have to replace the whole filter bowl assembly? And if so where would be a good place to get this part?
View 5 Replies
I got the new ones, (as mentioned in another thread) and they're the same as the old ones. Well, the one that's still in one piece.
I guess I'm missing something very simple, but as easy as it would be to cut the old one out...how do I make room between the lower leaf and the other leaf pack to get it out?
I about hung from the lower leaf and it didn't move quite enough to give the room to remove the bumper.
View 5 Replies
Replaced front leaf springs to procomp, now i got a clunking noise from right leaf spring rear eye(and a little bit from the left).
Can it be that:
I've tighten them to much? Wrong way (big eye is in front)? Got about 4" lift in front and haven't received rear leveling kit yet so the angel is wrong?
View 10 Replies
I am replacing my rear leaf spring hanger and shackle. I have one side done and the other side the old hanger is off. I am ready to install but the bolt/ bushing in the leaf spring will not come out. I tried every thing with what i had for about 2 hours. Is there a tool to remove these things similar to a ball joint press.
View 14 Replies
I've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
View 14 Replies
