I have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 RepliesI have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 RepliesMy truck was running fine, it's stock as far as I know. Shut it off, it sat and cooled off for a while. When I tried to crank it, it wouldn't start, threw 2 codes. P2285 and p 2623. I unplugged the icp sensoran tried to start, no start. Plugged it back in and it started fine for the rest of the work day ( I work out of it). Drove it the next day without any issues. Today went to start before work and no start with the same 2 codes. What should I check first? I don't have any monitor yet. Bought the truck a month ago as a work truck. It has 164000 miles.
View 4 RepliesCode was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 RepliesWe just bought and '05 F350 Turbo Diesel, about two days after getting it the check engine light came on. We had the dealer check it since the mechanic wasn't in and it came up as "Fuel Level Sensor" . My husband can't remember the exact code. We have been told it's no big deal but we want it fixed and the engine light to go off. The dealer is giving us the runaround, or at least I think so.
View 14 RepliesI've got a 2006 F350 5.4L.
The ABS light came on and it was throwing a 'rear speed sensor' code. I searched around and it seemed to be a common issue that the sensor goes bad and needs to be replaced.
I bought a sensor and replaced it, but in doing so, I saw that while the sensor was indeed bad (cracked) the wire right at the connector was corroded.
I replaced the sensor but the ABS light is still on the dash. Is it possible that they code simply needs to be cleared? I was able to read it with my OBD2 dongle and Dash Command App, but maybe I'm not able to clear it?
Or is it more likely that the corroded wire on the connector is the issue? (it wasn't fully corroded and I cleaned it up and sealed it.). It didn't look like I could pull the wires out of the connector, so I assume I'll need a new connector. What is the part number?
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 RepliesI am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesWhere is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesEngine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesPurchased my 2012 6.7 about 3 weeks ago. Driving yesterday the CEL light came on. I took and had the code read and it was determined that EGT sensor # 4 was bad. Also how far can it be driven before it leaves you stranded since the closest dealer is 35 miles away.
View 2 RepliesSo I had an ABS light going on and off on my 05 250, finally got it read, and the computer said right front speed sensor. I changed it and the light stayed on all the time then. I had someone plug it in and drive it and the left front sensor was reading nice and flat on the graph, while the right front was spiking all over the place. I then assumed I got a bad sensor. I changed it one more time and now the light still won't go off. Now what?!
View 11 RepliesAny way to disable the reverse sensors by maybe adding a switch to turn off power so it does not constantly go off while plowing and the sensors are snow covered? i thought maybe by just unplugging the switch would do it, but that did not work. truck is an 02 diesel with auto trans.
View 6 RepliesMy engine light came on a friend of mine did a scan and came up with o2s12 showing low voltage.we need to know which side and location of sensor..the truck is a 2005 ford f250 super duty 5.4l.
View 2 RepliesI was driving into the night a couple days ago and noticed first that the dash lights are not working. As it got darker I then noticed that my tail lights and running lights were also not working. I have a 2002 F250 powerstroke extended cab. I pulled the fuse panel cover off but can't find a blown fuse.
What fuse number would be suspect, and also if there may be a bad relay in the mix? The daylight sensor on the dash does not seem to be functioning either. In good light the headlights stay on (when switched to automatic mode) no matter if it is covered or not when the ignition is on.
2007 E450 Van. Dash light came on. OBD2 reader indicates: P2196 Ford - Lack of HO2S-11 Switch Sensor Indicates Rich
I need to find out which sensor to replace. It looks like I need to replace Bank 1, Sensor 1, but I am not sure where it is located. My guess it's located on the manifold, but I'm not sure if it's driver or passenger side.
A friend says, "Look in the owners manual for the van and find out which cylinder is cylinder number 1. Cylinder 1 is always on Bank 1."
The owner's manual has no indication of where cylinder one is located. I do not have a service manual.
I am not highly technical, but I do think I can replace the sensor myself, or at least I would like to give it a try.