My Superduty recently started clunking when I accelerate from a dead stop. The harder I hit the gas,the harder it clunks. I unbolted the driveshaft from the rear end and the yoke slides easily. Tranny mount looks tight. Could it be the front driveshaft? Sometimes when I brake hard and the truck comes to a complete stop it will do it too.
View 14 RepliesI have a 2002 F-250 7.3 Powerstroke 4x4. My truck has developed a "clunk" for lack of a better term when accelerating from a dead stop. It is not a shudder as it only happens once within a few seconds of depressing the accelerator and then goes away until the next time I stop moving.
It feels like either something in the drivetrain is not engaging right away, or something is releasing, like a stuck caliper or something. From the way it feels and what I've read so far about the TC/Trans, I'm assuming it is something worn in the drive-shaft/rear diff.
But it needs brakes badly (already have all new rotors & pads ready to install) so maybe a caliper is sticking when depressed and then popping loose under initial acceleration? I think this is unlikely but possible.
I took my truck in for a clunking noise in the driveline as I come to a stop and sometimes when shift into park. It is now the 7th and I'm told parts have been ordered and the truck will be worked on when parts come in. I asked to speak to general manager and still no call back. I called customer relations and nothing they can do.
Honestly I think the have me on the back burner since I'm warranty work opposed to marked up repairs. Am I being unreasonable on my expectations of repair time? I called around and a ring and pinion job is quoted at 3 days at the most. Other repairs have been approved as well and parts are in for those, but they have not actually repaired them either.
I have a 2001 F250 SD V10 and when at a dead stop and with the brakes applied, steering becomes very stiff and almost impossible to turn the wheels. If I let off of the brakes and move a little the steering is just fine. I hate like hell to spend the money on a new power steering pump if it isn't going to fix the problem. Simply put, deap stop, brakes on, wheels don't want to steer. How do I fix it?
View 10 RepliesI am experiencing what feels like a "bump in the rear" when initially starting from a dead stop. It feels like a car behind me tapped the bumper or that the truck "hunkers down" first, then moves. Tranny seems fine also. Once moving, there is no problem whatsoever. There atre no noises, leaks, or other symptoms. Also, when coming to a stop, it feels the same way just before the truck completely stops. If I drift forward a little, then apply the accelerator, it does not "slip" or hunker down.
Took it to the dealer and they claim that they can't find anything wrong and may just be the suspension releasing? The truck does this whether loaded or not?
2001 F250 CC Lariat SB 7.3
So, on my drive home from the pub tonight, my clusters went dead, then came back on, then died again. This behavior repeated for the 5 mile drive home. In addition, I believe the lights weren't working as well. The engine was still running, so I simply continued on home and parked for the night. The only thing I can think of might be the problem is the fact that I replaced the serpentine belt the day before yesterday. Is it possible that the alternator is not charging the battery properly and that is what my problem is?
View 14 RepliesI have a 2005 ford f250 6.0 I was driving back home from a interview and my truck died at a stop light it would crank but no start I tried replacing the stc fitting didn't work so the I replaced the ipr still didn't work bought a new hpop still didn't work I'm lost at this point I have low pressure oil pump is working new icp, what is going on?
View 8 Repliesi have an 04 f250 5.4 4x4 250k miles+ ...the truck has been acting weird lately. I has 0 power...i went to pass an 18 wheeler today at about 15 mph and gave it about half throttle...well it held first gear till about 5 grand then slammed into 2nd...It just has 0 umph ... it wont even consistanly pick up speed at half throttle or over..the rpms will stop ...then pick up...then stop...it always accelerated smoothly....it is bogging really bad...it was downshifting into 3rd today on little overpass hills that it NEVER does that on...something is telling me torque converter BTW no codes and no flashing overdrive light
View 14 RepliesMy trouble is upon turning key to start everything goes dead (no power to anything). Does not always happen, sometimes she starts just fine.
After the power cut out if I turn key off, wait a minute, then back to on position she will sometimes come back as normal or sometimes the on "ding" will chatter and dash lights will be dim.
I have checked batt connections, starter/solenoid connections, block ground connection. All seems fine. Get same problem when I jump starter with screwdriver. Been suggested to me ignition switch to blame.
Like the title says, if it sits over night the battery will be about dead. The cables were replaced 6 months ago and are in good shape. I could not find and bad spots on the wires I can get to. One odd thing to note, with the key out of the switch I opened the passenger door to check the glove box light and the truck started chiming like I had opened the drivers door with the key still in the switch. Would that indicate maybe the key switch could be the issue?
View 14 RepliesAm i correct in starting to look into why I can't hook a scanner or Torque Pro bluetooth up to my truck and starting with blown Cig lighter fuse? (Cig lighter doesnt work, power port does)
View 1 RepliesNot sure if it's a bearing or some kind of U joint. I am just starting to feel a little clunking in the wheel on a rough road. It is not bad but I feel it, is it hard to fix this issue, and what is the correct part I am looking for. Steering Wheel Bearings? This is for a 08 F350 SRW 4X4 KR V10
View 7 RepliesSo I have a no start on my 6.0. I was driving and went to accelerate and had no power, pulled off of the road and was idling rough, I checked for fuel leaks-none. I put it in drive and engine cut off and wouldn't start again, changed the ICP (threw a code) still nothing, FICM is good, ICP is 950 psi at cranking, IPR is only at 54%. I'm at a loss of what to do next besides looking at the IPR, and I do not have the equipment for a leak test.
View 5 RepliesI have 2002 F250 4x4 with 5.4 V8. It has auto locking hubs. If I haven't used the 4wd lately I have to manually lock the hubs in, right side sticks, so I have to use pliers to lock into place. After a few times it works in auto fine. Anyway my issue. I went to use my 4wd so I manually locked the hubs, hopped in the truck and flipped it into 4wd. When I did the instrument cluster died. Radio, power windows and locks, turn signals all work. I just don't have any speedo, tach, fuel gauge, water temp, battery, no odometer. All went blank. I checked some of the fuses that I thought it could be from the owners manual but still no luck.
View 3 RepliesI pushed the Tow/Haul button on the gear shift and my instrument cluster went DEAD. Have checked the 3 fuses labeled instrument panel (F4,F35,F41) and they look OK.
2003 F250 6L diesel .....
I have a problem. 2002 F-350 4R100 tranny. Put a reman transmission in about 30000kms ago. pulled excellent with no problems. shut it off for night. In the morning it had absolutly no forward and a little bit of slipping reverse for a few minutes now it is totally dead. No movement either way. The OD on off flashed a few times but not anymore. Put a Genisys scanner on and no codes at all. What could be the issue?
View 14 RepliesI'm installing an aftermarket radio in my 2004 SD. The illumination control stopped working (when I turn on the lights, the radio doesn't get darker), and now the dash and a/c panel aren't backlit any more.
This is the first time I've driven it since the new radio. I thought I might have seen a spark when testing to see which wire was the illumination control, but I'm not sure. I've got a fuse box diagram, but so far all the fuses look good.
I have a 2002 f250 7.3 with a dead pedal and gauges. This has happened to me once before checked fuse 45 and it was blown. I didn't know that the po used a 30 amp fuse when it should have had a 15 amp. I replaced it with a 30 not knowing. Well coming home the other night it happened again gauges dead and pedal. Checked fuses all were good. Found this site and read about the cause in the shifter. Took that apart and fixed the wire that was broken in half. My question is what else is fried now from having a 30 amp fuse in while it was shorting out since I have no gauges and gas pedal.
2002 f250 banks six gun
banks 4 inch exhaust
My 1999 f-250 7.3 has been sitting for months, and I went to start it and both batteries are dead. Replaced both batteries and at first the alarm went off like normal. Turned the alarm off, hit the unlock button and it beeped like normal. Got in and stuck the key in the ignition and tried to turn it over. Completely dead. Now I cant even get the alarm to go off, showing no signs that its even getting any power. And all I'm hearing is a low clicking noise in the cab.
View 5 RepliesI have a 2000 F250 SD with the V10 engine. The problem that I am having with it as of late is that whenever I perform a full turn I hear some clunking coming from the front end. The clunking is similar to that heard from cars that use CV joints FWD but of course it sound more "manly"
Anyways, my truck has the full axle on front so I suppose it could be either the u-joint at the hub or the hub itself. I would like some pointers so I can acquire the required parts.
2004, 6.0, 96,000. I noticed a occasional clunking under the passenger foot area. The exhaust pipe is loose at the turbo connection on top the engine. It is swinging L & R & hitting the spring hanger & transmission cross member. Is there a rolled pin, dimple or other alignment device at the flange at the turbo???
View 4 Replies