Ford Super Duty (1999-2016) :: Check Engine Light On - Exhaust Gas Temperature Sensor Circuit High
Feb 3, 2016
I've owned my 2012 F-250, 6.7L for less than a week and it has a check engine light. The local dealer can't see me for a week, and I need to leave town next week.
I went to AutoZone to have the codes checked and this is what they came back with:
P2033
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
P2031
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
Can I drive on these codes, or should I park the truck until Ford can see me?
View 2 Replies
Advertisement
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 Replies
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
View 1 Replies
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
View 2 Replies
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
View 3 Replies
Just about every trip i take my temp gauge pegs and dinger goes off and check gauges lights up in the message center. It eventually will go back to normal or if i shut key off and restart truck it goes to normal. im guessing it is the temperature sensor for the gauge but not sure?? If it is, where is the gauge sensor located?
View 14 Replies
My truck has a bit of an interesting trait. Unless it's just about freezing, my transmission is just about always at operating temperature. If it's 50*F outside and I start the truck, the Trans temp is smack dab in the middle. If it's 30*F outside it starts just a little above cold then is "warmed up" when I drive it down my short street block, which ain't right.
All the rest of the time, it's always reading middle of the bar temperature. My old 5.4L never did this. My 7.3L does. Best I can tell is it's a fault in the temperature sensor for the transmission. I don't have a scan gauge yet to get the readings but will be getting one. Just need to know where the sensor is at so I can have a starting point.
View 3 Replies
My truck is a 2000 7.3 doesn't smoke on start up but once it gets to temperature it does. I'm not going through any antifreeze, just oil and it's coming out the exhaust. The truck still runs great starts right up every morning without being plugged in. Any opinions?
View 3 Replies
P0073 Ambient air temperature sensor circuit high. Preliminary inspection, right outside mirror badly damaged/broken. Guess where the sensor is?
View 6 Replies
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
View 14 Replies
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 Replies
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
View 2 Replies
Pulled into work and the truck was running fine then i got out and shut it off and went to start it again to move it 5 minutes later and it would start and misfire and chug and the wrench light came on as well as check engine and abs. I replaced the throttle body motor with the doorman part and I'm installing a new electronic pedal today as well.
The weird part is the chugging as i replaced all plugs and coil packs, plugs are champion double platinum. when all this started it was raining pretty hard out side I've cleaned all plugs with compressed air and used dietetic grease on most until i ran out. Truck is a 2006 f250 with 3v 5.4 automatic... Truck is my work truck and i am stumped on this .....could cam sensors cause the same issues? What about egr valve?
View 5 Replies
1. About march 1, my check engine light came on- took it to oreileys for a scan and said Speed Sensor A (cannot remember code), I was not overly concerned to fix it very very busy.
*Drove about 800 miles no further issues except the annoying CE light*
2. ABS comes on a few days ago
3. Today the truck, 4 miles from home decides it wont let RPM's get above 2500, and 40mph. It slightly hard shifted once.
Truck has 97000 miles and is a 1999 V10 has NEVER had any tranny shifting issues or engine issues....
4. Check tranny fluid when we get home it does not smell burnt and is red- its not even that warm...
I have read a couple places that a VSS can cause this? But I never noticed my speedometer acting up EXCEPT for the day the CE light came on- which there was a lot of ice and tires were spinning and speedometer said 0.
View 1 Replies
I literally just purchased a "new" 06 F350 and have had it just over a month. I bought it from a used car place in Salt Lake City and have put roughly 250 miles on it, it has 105k on it. While having 1 sled in the bed and towing a 1-place snowmobile trailer up a 8% grade my check engine light lit up. Little back story, there was a slight hiccup that I started to realize it had about a few days after purchasing it, would kind of buck a few times under normal acceleration around to 40-60 mph not every time just occasionally. Been meaning to take it to a friend to have it looked at, just been fairly busy.
Now when I was driving it back home (~8-10 miles, almost exclusively downhill) at stop light and accelerating from 0mph it would not prime the boost, I was getting almost no power until I hit 2000 rpm then all of a sudden things were fine turbo would engage I was able to drive normally. It hasn't moved in 2 days as I will not drive it until I know what is wrong with it. In doing a little research I read about turbo veins being stuck open, ignition problems, and a few other things that might pertain to what is going on with my truck. I have a buddy coming in the morning tomorrow to pull some codes with a scanner so I will have more information here shortly but I just wanted to get the conversation started on this.
View 6 Replies
Solid yellow engine light. Sounds and drives fine. Is it always emissions or can it be something bad? I was going to leave sunday for a 2 month trip pulling the RV. Now stuck waiting for wednesday for dealership.
View 8 Replies
I have a 2006 350 6.0l check engine light came on today truck is running normal except the fuel gauge and mile to empty gauges keep changing when I turn the truck off. What this could be?
View 1 Replies
2001 F-350 4x4, 5.4 automatic.
Where to start , check engine light is on. Nothing seems wrong , trucks running good , nothing happened , just the light. I kinda like the truck so I would like to find out what its issue is?
View 2 Replies
I have a 2011 f250 with the 6.2 liter gas engine. Lost power and the check engine light came on. I pulled the codes and it is a camshaft position sensor and 4 other codes for misfire on all cylinder for that bank. I can't find any info on where the sensor is located or how to replace it.
View 2 Replies
I have a 2011 F-550 XL truck, I had a problem with an open injector4 and was forced to replace the engine, later, I had a problem while installing an OLEP kit, misplaced the hose and killed the engine (...i know... ) so, I changed 3/4 of the engine, just mechanical parts and reused the wires and cables, now the check engine light is ON with an oil pressure error, replaced the sensor and the error remains, replaced the computer and guess what ...again, the same error. What might be going on?...
View 1 Replies
I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.
View 1 Replies
