So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 RepliesI am looking to replace the carrier bearing and (u joints while I'm in there) on my 08 F-250. I do not have access to a lift so this will be done while on the ground. Am I asking for trouble by doing this on my back?
View 14 RepliesI started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
Actually the previous owner of my 7.3 Dually cut the muffler out and straight piped it, it's really not that loud but too much drone for long highway hauls.
What's a good replacement muffler for a 7.3? Wouldn't mind a little bit of sound, it already has an oversized tip.
I am not sure which it is but I cannot turn the pulley by hand. How do you tell if the pulley is bad or the whole compressor? I went out to start the truck and it wouldn't start. It died so I restarted it and then I seen the smoke from the front of the truck. I opened the hood and the flipping belt was just hanging there. Is there a way to just bypass the unit for now? I wont be needing the AC till summer and that is several months away.
View 3 RepliesHow can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 RepliesHave a rear wheel bearing making some noise. A friend told me that it is always the outer bearing that goes first . Can you replace the bearing without replacing the race?
View 14 RepliesI am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 RepliesNeed to replace the ac compressor bearing/pulley on my 2001 f350 7.3. My question is do I need a special tool like a pulley puller or is there another way to remove pulley? I already have the clutch assembly removed as well.
View 1 RepliesI have a 2000 F-250 SUperduty with a dana 50 front end , and as most of you know the front hub bearing's are junk, and expensive to replace. I know dynatrac has a kit to convert it to the tapered, cheaper, servicable bearing's. But 2g is a lil out of my price range. I was curious if anybody has tried takin the knuckles and stub shafts off an older dana 60 and putting the knucke's on the front axle to get the older bearing style instead of the hub bearing and the actuall lock outs instead of the POS vaccum style.
View 4 RepliesI have a 2001 F350 with a 7.3 diesel and automatic trans. I purchased it about 100,000 miles ago. It is all stock as far as I know. The mileage on it was about 14-15 on the road and I decided to put a chip in it. I was somewhat leary of putting too much power to this old of a rig. I put a TS Performance chip in it. It seems to have more power. I am towing a 30 ft. Gulfstream Seahawk I think around 10,000 lbs. When I started up a hill it made a different noise like a screeching noise when I pushed it. When I back off a bit the noise goes away. When I put it back to stock setting the noise is not there just the normal downshift and increased RPM. Not sure how to describe the noise but sounds like a metal bearing type noise. I get the same rush of air or what ever that sound is when it changes back to a higher gear. Is this sound normal or what might it be. It sounds normal when not pressing it.
View 6 RepliesI have read the older posts here on the super duty ford 4x4 system. At 60,000 miles I noticed what sounds like a gear or bearing noise, or even a whining noise like you would hear from mud grip tires, coming from the front end area, while driving back from Kentucky to Georgia. I have quiet running street tires on this pickup.
I have a 2004 F350 crew cab XL, automatic, 4x4, limited slip axles, 430 gearing and a V10. This truck has always been extremely quiet on the highway. This noise I described above has increased and the truck now has 70,000 miles. I have the factory 4x4 dash switch in my truck cab for the 4x4 engagement. I always thought the dash switch engaged and disengaged the transfer case, and locked or unlocked the automatic hubs.
The service guy at the dealer now tells me that the dash switch only locks and unlocks the front hubs, and the front drive shaft and front differential are engaged full time. So, after checking my tires for defects, and for any play or bearing noise in my wheel bearings, I am looking at pulling the drive shaft out keep the front differential from turning, to determine if I have a bad bearing in the front axle assembly.
Now I read some of the posts here, and they say that with the dash switch in "2 wheel drive", the transfer case should be disengaged and the front drive shaft and front axle should not be turning at all. What is turning up front with the 4x4 disengaged on the dash switch ? I'm afraid to drive my truck out of town now and I need to isolate this issue and get it repaired. This has been a great truck and it's very reliable.
I replaced my alt. because in the morning the bearing would squeak and the head lights flicker. It was a life time alt. Put the new one in now it wont charge. Took it back and got another, same thing. Also replaced the starter relay and battery. I checked the fusible links and replaced a terminal connector. The wires look good. There is 12v on the alt lug and pins 1 and 3 on the connector with the key off. Turn key on and 12v disappears form pins 1 & 3. Also checked all fuses in both boxes. I ohmed out the wire harness from the alt back to the connectors, all good. What am I missing? This is a 99 f530 5.4l.
View 9 RepliesI have a 2001 f250 v-10 4wd with 117,000 miles. I just replaced drivers side front hub bearing assy and not sure if it's the new bearing or what but now I keep hearing this crazy noise from suspension area. It has had bangs and pops for a while now. It almost sounds like abs motor going off but louder. Does it going slow fast or whatever. Brakes on or off. Trucks ball joints were done about two months ago and new shocks, trac bar replaced this summer only thing not done was tie rod ends and all bushings. Brakes are good new rotors and pads this summer also. It's like taking two inflated balloons and rub them together real fast. It may be the timken bearing maybe bad from get go.
View 14 Replies2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesI am working on my Dads 01 super duty with a 5.4, automatic, and the pinion bearing has seized up due to a lack of fluid from a rusted out rear diff cover. The tag on the diff cover had a 10.5 stamped on it and has 12 bolts. Is this known as a ford 10.5"
I have changed gears and pinion bearings in a Dana 70 before is this the same process? What are part numbers for a new pinion bearing and seal? Gears are in fine shape.
i replaced my a/c compressor on my 2006 f-250 2 yrs ago but had not refilled with r134..only the pag oil. Now i decide to refill seeing my wife uses the truck and compressor would not engage, i was able to bypass it by removing relay and jumping it with a paperclip. Compressor started up but seems to have seized on pully. the pulley seems fine and still turning freely. I can no longer turn it manually when truck is stopped and i could before i jumped it. could the clutch only be replaced or does the bearing and pulley have to be replaced
View 10 RepliesMy truck had devolped a whine/howl over the past coulple hundred miles. I thought it was a wheel bearing failing me. So yesterday I pulled it into the shop and jacked up the front end. Everthing checked out fine so I jacked up the rear end, started it up, put it in gear and to my surprise the noise was from the rear end.
I pulled the rear end apart and found the front pinion bearing had a defect in the race and the rollers were starting to pit out causing the noise and harshness when turning it. The truck has 130k, seal wasnt leaking and fluid looked/smelled normal. I think it was a legitimate defect not from abuse or lack of maintenance.
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 Replies