I pulled the trans to replace the clutch and now I cannot get the trans to line back up! I am using a trans jack then two floor jacks with a 4x4 across them to support the transfer case. I am about four inches from the block and either side is either 2 inches high or low. The truck is 1999 f250 7.3 4wd.
View 10 RepliesI'm having trouble disconnecting the transmission lines to replace them. I can't get them off. I have the tool. Can I replace the fittings in the radiator?.
View 3 RepliesI have a grinding/Rattling noise coming out of the front area of the transmission when the clutch is disengaged (up), noise stops when clutch is pushed in. 99 (6/98) F-350 7.3, manual, 4x4, 192xxx mi. Just came out of the shop with the following done to it:
New Power Force clutch kit, twice.
Transmission Rebuilt twice.
Different rebuilt transmission.
Rear main seal r/r.
After first time in shop the noise was apparent. about 3,000 miles were driven with no change, brought back to shop, where transmission was gone through again as well as a new clutch set, same noise still present! Another transmission was rebuilt and installed, same noise!!!
so while replacing the rear brake lines in my 2001 F-250. / 5.4, the flex line that drops from the frame bolts to the axle through the axle breather threaded vent line. The friggin thing crumbled on me and now I can't find a replacement for it. Where I can get it or what it's actual name / part number is so I can call the Ford dealer and hope it's not obsoleted?
View 3 RepliesThe trans temp guage on my '08 F-350. V-10 started acting erratically, and the wrench icon popped up on the display. i crawled under the truck to look for the sending unit and it's lead. i assume that i found the lead. it is encased in a corrugated sleeve, and appears to be a vaccuum type tube and boot connector? the boot still had a small round gray cap plugged into it. it appears that the cap was never glued (go figure) upon assembly. i have tried to reach up on top of the trans to find the sending unit to figure out the best angle of attack. i can barely touch it with the tip of my finger. going with mechanical guages is out of the question at the moment, so i'm wondering can it be driven any distance this way, AND any schmooze tricks developed to get at the sucker without dropping the cross member or exhaust????
View 3 RepliesI'm in the process of replacing the clutch master cylinder in my 99 F250 7.3L. I've got the kit that includes all the components already pressurized in a complete assy. Anyway, I know that in order to remove the clutch pedal component, (the part that stick's thru the firewall) your supposed to be able to rotate it about 45deg and it should pull free from the piston attached to the clutch pedal. But, what happens when it will not come free? I've already got a new replacement kit and I can see where that stainless rod inserts into the plastic component, but I can't seem to get the one on my truck to release?
View 1 Replies I recently replaced my Ford Factory clutch with a new LUK kit, lever, pivot & hydraulics and I have to say it is absolutely perfect. If you are going to take the time to do the clutch, do it all. While we had it apart, I decided to push up my Up-Pipe replacement and do it while the transmission is out. What takes several hours to do is done in 30 mins this way. As we all know when we start in a job, we see other things and say well while it is apart I may as well do this, and do that. I decided to do the U-joints in the rear shaft. I had marked the shafts prior to removal for orientation but my assistant did not mark all 3 U-joint knuckles when he changed the joints and reinstalled the shaft.
I took the truck out for a drive and starting at about 15 MPH all the way to 60 ( I dared no faster) it was making me nauseous. Today I looked into it, marked current locations and started rotating front and rear joint 180 to no avail. I said lets just rotate the center joint and go from there. as I was pulling the carrier i noticed a HUGE but dull yellow arrow on the short shaft. I decided to look at the rear shaft and found a HUGE but dull yellow arrow 180 degs from the front. It looks like it could have been a factory mark. I repressed the center u-joint so the 2 arrows line up and the vibration went away. I can not express the aggravation this could have caused if not for those arrows. Take the time to properly index the drive shafts, it will save you tons of time and agitation.
Have a 2007 V10 and I want to put in a Magnafine tranny filter. Instructions say to plumb it in to the return line. Which one is this, top or bottom?
View 11 RepliesOK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
I have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 RepliesI have heard that the front brakes are separate, and if the rear brakes have a leak and the line is empty, the fronts should still work. Is this likely to be true? If I drive the truck will I be able to stop with the fronts alone (assuming they will still work?)
I plan to drop the truck off late tonight when there is likely to be no traffic, but thought I would ask.
So my brother swears by sea Foam and has been telling me to run some of it through my truck. Question is,i just put new spark plugs in less then 5,000 miles ago. Will i have to change them if i run sea foam through the booster line and gas tank??
View 8 RepliesWhy on my 2001 Superduty if you blow a line nothing works and you have no brakes? On my older vehicles I think it was called a duel Master Cylinder and if you blew lines in front the back would still work and if you blew a line in back the fronts would still work. When I blow a line on my f250 there are no brakes at all making it quite deadly.
View 3 RepliesMy transmission cooling line is leaking. It leaks where it connects to the radiator. Im not sure how I go about removing the connection from the radiator. It is tough to tell from the rust on the connection weather or not I can use a wrench on it. I have read here that there are cooling lines in this part of the radiator for the transmission. Is it serviceable or do I need a new radiator. I dont want to touch it until I know what I'm looking at.
05 F250 5.4L 4x4
[URL]......
I filled my coolant yesterday after driving to the "max" line. Today when I awoke it was right at the "min" line. I didn't see any noticeable liquid below the truck, except under each front fender but I think this was water from the dew evaporating/condensing and running off the truck. What happened to the coolant or did it just cool down and condense. It got pretty cool last night (mid 40s). I have an 02 f250 5.4L ... I feel like there is a leak somewhere, any link to or a procedure they can explain for finding it?
View 10 RepliesThis is something to check, I found the vent line pinched closed on my 2000 F350 when I was trying to find out why it was leaking. When I was under my 2013 installing the hitch I checked it and found the same problem. The clip doesn't pinch it closed right away but it will happen if you don't move the clip.
View 8 RepliesFirst, I am fortunate that I was only going 25 mph when some turned in front of me causing me to slam on the brakes. The pedal went to the floor, but did slow the truck enough to miss the jerk. Had I been on the highway, it would have been very bad.
Anyway, what I found is still hard for me to believe for two reasons. It find it hard to believe it failed, but more important that I am getting the last national inventory of 2 of the 3 lines in this picture (according to my Ford dealer).
The three lines are almost directly under the front end of the master cylinder between the block and frame. These are as I found them. The larger one goes to the rear feeding both rear brakes while the two smaller run to the front brakes. The spring looking part below is just a plastic protector. The line which failed goes to the front left.
I think anyone with a 2005 SuperDuty which uses the same or similar parts should take a very close look at the flex sections. The parts I have ordered are: 6C3Z-2B523-BA, 6C3Z-2263-BA, and 6C3Z-2264-BA (rear, right, and left).
How long a manufacture is required to maintain inventory? I thought 7 years, but someone suggested 17. I'm at 8 years, but I would have expected more than 1 each of the fronts to be available. Do they changed parts on the '06 or '07?
My 350 spent 2 winters in the Chicago area and has been resting in Florida since 2006. No work was done in this area, but the closest work was the main fuel pump (frame mounted) replaced 2 years ago, but that is almost 2 feet to the rear.
I have noticed that in the past 1-2 months my trans probably has just get to 150*. Even on warm/hot days. Lately its just been 120-140 all day every day.
Can this cause any problems? It used to go up to 150-170 when warm, now it takes a hot day to get there.
I assume its fine, but just checking because I have, admittedly, neglected my trans fluid.
My tranny only goes to 3rd gear in 4x4 lo is that normal? 2014 6.2 xl f250 ....
View 14 RepliesSo this is my major problem, leaving for a camping trip tomorrow afternoon. It's just 15 miles away, easy flat drive. What has happened is the trans line coming out of the bottom of radiator is leaking next to the fitting about an 1/8 ' out, So I can't cut off and splice in hose for the trip. I worked on it for about an hour, rusted on, tried some heat and now have some PB Blast on it and all I am doing is starting to round off the head of fitting. Is there any way to bypass this just to get the camper to campground and then get to a shop while we are gone Don't care if I have to splice and cut, will get new lines later.
2004 f250SD 5.4 83000miles
So my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 Replies