My 6.0 lost a bolt that holds the AC clutch and the clutch fell off. It's probably on some highway making people have flats. Is it possible to buy a replacement clutch and NOT remove the OEM pulley, just take the parts off the replacement clutch and put them on the old AC and existing pulley?
View 9 RepliesBad news: Radiator fan fell off while driving tore up fan blades. It is going to take them a week to get the parts!
Good news: My extended warranty is good for 10 more days! So the fan and fan clutch need replaced.
Should I insist that they replace the serpentine belt that rubbed on fan (50,000 miles on belt, original belt) and the water pump? It put a good dent in the radiator but didn't puncture it.
My Bump Stops have completely dry rotted and fell off the truck. I have an 08 with a 2 inch leveling kit, I already did all the body bushings, as they disintegrated as well. Should I bother replacing them? I highly doubt that I would ever bottom out that bad that I would need them?
If I should replace them, then where did u guy's get them and should I go with the Neoprene like I did with the body bushings?
[URL]
How to troubleshoot?
View 14 RepliesThe other day I had a metal pin fall out from under my dash and hit me on the foot (only reason I would have know if fell out till I clean the truck)
Ever since then the gear selector handle for my transmission has become sloppy and when I go to turn off the truck, I have to hold the arm up to turn key off all the way. I have looked to try and find where it goes and cannot find the location. I have also looked at a blown up parts diagram and cannot find it. Where it goes?
2002 F250 SD V10 with auto...
I have a 2006 F250 and the other morning I came out and found the rear view mirror laying on the cab floor. No biggie, I'll just glue it back on. Then I noticed the small black decal looking thing on the inside of the windshield. My question is, does this have to come off in order to re-install the mirror with standard Permatex mirror adhesive, or do I just put adhesive on top of it? Also, is there a different, specific adhesive used here that won't crack the windshield 2 weeks from now, like I read. Took a closer look and realized they used a thin adhesive patch to attach the mirror. I'll get one from the dealer.
View 3 RepliesGot a 06 F250 V8 Gas. Went to turn AC on the other week & got warm air out vents. Put 1 can of 134 in & the gauge on the "kit" said it was in the green. It was working last summer. You can turn the compressor "face" so it's not locked up, but it's not kicking in. Swapped the replay with another one & the 10a fuse in the fusebox under the steering wheel is good. Is that the only ones? I find it hard to believe that it's something serious. We did change the belt a few weeks ago & I was hoping that we had pulled a wire loose. The vacuum line that plugs into the heater hoses is plugged in.
View 14 RepliesI pulled into my driveway after a 30 minute drive and smelled burning brakes. The right front was the culprit so I took a garden hose and cooled it down. The next day I remove the caliper and one of the pistons fell apart. So I need a new caliper and trying to decide if I buy after market or go with Motorcraft? I think the rotor, caliper, and pads are original since I the rotor is stamped Ford and the caliper bracket has TRW and Ford markings.
View 12 RepliesToday I either broke timing chain or it fell off on the passenger side bank of my 08 F250 V10. Put a hole in valve cover. What to expect for repairs. Is this engine Zero tolerance.. unsure if I should expect bent valves or not and just how far I may have to go with this.. best way to test. I have a bore scope camera and mechanical abilities.
View 14 RepliesI noticed a thumping sound in the truck bed when I'm driving and took a look underneath. The rubber gaskets for the truck bolt are all rotted and falling apart. Does it have to be replaced?
View 5 RepliesNeed to know if the 5.4 and 6.8 use the same bell housing pattern?
View 5 RepliesI've a 2002 Ford F250 SD with the 5.4 v8. I noticed my truck is missing at aprox 50mph when the truck goes into OD and revving at aprox 1500 rpms. I Changed my spark plugs and cylinder no 6 was fouled. The coil was cracked where the sensor connects to the coil. I used some JB weld to try and repair the crack. My truck is still missing and vibrating at 1500rpms at 50mph. I wonder if I need to replace the cracked coil? my check engine light is not on, but that means nothing.
Also, cylinder no2, I was not able to remove the coil. The bolt is stripped. I just got this truck a few months ago and the previous owner or last person who worked on this truck left me with a stripped coil bolt. Anyway, how do I get this bolt out? I'm afraid to crack the plastic area the retainer bolt threads in to...which is also plastic. I"m not too fond of my ford, at least working on it.
What is the thread size/length of the 20 transmission pan bolts on the 4R100? I am replacing the pan since the rust has finally started weeping ATF, and the bolts need to be replaced as well, they have turned into little rusty nubs. So i want to use stainless ones. I could pull one and go to the hardware store, but what is the size i can stop on the way home.
View 14 RepliesWhat is the size of the bolts on the rear axle that hold the shock absorber? I believe its an M12 x70 mm long??
View 7 RepliesMy steering wheel is loose as in moves back and forth if pushed or pulled right at the wheel.. everything else seems tight and still turns and drives fine.. took off the airbag and the center nut is tight.. it's been getting progressively worse since I bought it.. What it could be??? Loose bolt or nut or the steering column?
View 2 Replies2016 F250, took out the seats to remove the console and install the jump seat and upon installation I stripped the bold housing for the front left corner of the drivers seat. Now it won't tighten up. Am i going to have to tap the hole and get a bigger bolt now?
View 12 RepliesI have a 99 F250 Super Duty 4x4. The u-bolt bracket on the front passenger side has rusted through and broken in two places. It has broken right at the hole for one of the u-bolts, which then broke the sway bar bracket off (so the sway bar is no longer attached on the passenger side). Also, the track bar bracket has broken off.
Is there a replacement bracket that can be purchased? Or does it need to be fabricated from scrap? The u-bolt bracket, sway bar bracket, and track bar bracket are all one whole piece. It is welded to the axle, so it would need to be cut off. Then the new bracket would need to be welded back on.
Went to change the plugs on an 02 f350, the bolt holding the plug wire boot on doesn't seem to fit any standard size socket. 7 is too big, 6 is too small. 1/4 is too small, 9/32 is too big.
View 14 RepliesI am getting ready to make a set of front shackles for my truck for a temporary lift solution to fit my 35s until i can afford a complete suspension lift kit. I cannot for the life of me find the size of the hole for the bolts. I don't wanna drill it too big then have play in the shackle. My stockers are still installed so I don't have those to measure just yet. Need to verify the diameter hole i need to drill? and stock shackles look to be about 5.25" center to center, from what i can measure with them installed on the truck? so 2" lift, the new shackles will need to be about 9.25" center to center, right? (add 4", nets a 2" lift?)
View 7 RepliesSo I went to install a front end leveling kit in my 2003 2WD F250, looked like a simple task, except the bolt that holds the lower coil spring mount won't budge! I tried heating the nut, I soaked it with WD-40, tried a 200lb impact and a 30" breaker bar with all my weight. Is there something I am missing?
View 5 RepliesMy 2000 f350 is leaking oil from a bolt on the passengers side valve cover. it is one of the bolts on top of the valve cover. Can I just remove the bolt and put a rubber washer under it or do I need a new valve cover?
View 2 Replies