Ford Super Duty (1999-2016) :: Adding OEM Rear Overload Springs?
Jan 30, 2016
I would like to add rear overload leaves to my 2016 F250 that for some reason I didn't order with the camper prep package. From what my internet research tells me I will need to add the frame tabs and rubber bumpers, the overload leaves themselves, and of course longer U bolts.
My question is, in all of the pictures I can find, there in an intermediate spacer block between the regular leaf pack and the overload leaf. I can find a part number for this block ( 2C3Z-5594-AA ) only for 2002-2007 trucks. The parts diagrams I've seen online at various Ford sites don't list a part number for this block on current model trucks. Most just give a single part number for the whole leaf pack.
For 2014-2016 F250 with the camper package, or an F350 know what part numbers I might be looking for? Do the newer model year trucks still use an intermediate spacer block? Any chance someone with one of the aforementioned vehicles can post a picture of what the overload leaf setup looks like on a new(er) truck?
I would assume if you snap an overload leaf you can get a replacement from Ford, so why can't I find a part number for them either? I'm pretty sure I will have overloads built at a local spring shop anyway, but at least want to make sure I'm matching the correct and current factory setup.
View 14 Replies
Advertisement
I have a 99 SD 250 diesel, I also have a broken rear leaf spring. My truck has a 3 1/2 in. block between axle and leaf. My question is this. Can I remove the block and install 4" lift leaf springs without messing up my pinion angle? The blocks look square. But someone toldme once they are made to a specific angle for rotating pinion for better u joint alignment. Sounds like it could be true.
View 9 Replies
I decided to go ahead and do a rear block replacement. I'm going to install the Ready lift 4 inch blocks.
I have both u bolts and nuts off of both sides. Rear stabilizer bar disconnected and both shocks disconnected. However, when I raise the rear of the truck, the axle raises as well. What could be holding it on still? I noticed there's a nut in the middle of the leaf springs. Do I take that nut off? I just don't know what could be keeping it from separating.
View 11 Replies
Replaced my old sagging leaf springs with new X code springs. Had an almost impossible time centering the axle even with adjustable center link. Even with it totally maxed out it is just barely centered. Now I have a terrible squeak coming from springs. Is this because of the side loading of springs? Is there any fix for it? Not only do they squeak but the drivers side now sags almost an inch even with brand new springs. 2002 F350. Super annoying and irritating
View 1 Replies
This is my dads f250 build date of 9/03. I know these wheels are not the factory xl wheels. I also think they changed something with the wheel back spacing somewhere around this time. He is running 285/70/17 bfgs and is rubbing the leaf springs pretty good. He ran this same size on his previous 02 model with no rubbing. Can he get away with 1/4 spacers? What years these wheels are from? And the backspacing differences, if any. His 02 had the chrome large bullet hole style wheels.
View 5 Replies
I just bought a used 2013 F-250 4x4 and it came with the snow plow pkg. heavy duty front springs. I love the truck, but won't be plowing with it, and I don't need the rough ride (and don't like the look of the front end higher than the rear)
How hard is it to swap out the front coil springs and replace them with the "regular" ones?
View 7 Replies
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
View 10 Replies
I have a 2000 F350 that was once a work horse. Its now just my daily. The leaf springs in the rear have 2 broken on each on and the front need to be replaced due to 344K miles on them too. My question is how do I soften up my ride on leaf springs though? Theres a local shop that will do the work, but my rears have 7 leafs / front 2. It used to tow daily but I dont tow anything with it. could I go to 5 in the rear to soften it?
View 14 Replies
03 f350 4x4. New front calipers and pads.
Wondering if there's a 'trick' to getting the front brake pads into the caliper . Those damn springs kept popping out. I'd get three of the four ends into place in the pad holes then one would pop out while I'm trying to get the fourth in.
After about a hour of trying every different way that I could think of, another set of hands came by and with four hands holding things in place, it finally did the trick.
View 2 Replies
I am trying to get an extra set of wheels for my truck before we move back to Alaska to mount my studs on next winter. I have found a few used sets but then realized I have the tire pressure sensors on my truck. If I pick up a set, do I have to get ones with the sensors? Can sensors be added to the tire shop? I just really have no intel on this subject!
View 8 Replies
My 1999 SD was originally a Work Truck without cruise. I'd like to add cruise of some sort (factory or after market), but also trying to keep the cost and difficulty factors low.
Have any of you SD drivers ever done this and if so, what you went through?
View 9 Replies
I want to put in a SPD Y pipe. They make 2 different ones, 99-00 and 00-04. I have a 2000 and so I've been trying to figure out which one. The SPD website's phone number goes straight to voice mail and it's inbox is full. 5 star tuning who sell's these as well told to me to just "get under the truck and see"... I'm no exhaust pro so I don't know what to look for. I just went to a ford dealership and their diagrams where the same but it did show there were different part numbers for the two different styles, so they couldn't work either. It says on SPD's website that the exhaust configuration changed somewhere in 2000. So, what to look for in the difference. Maybe a picture of a 99 y pipe and 01 y pipe would work?
View 11 Replies
Putting a FLowmaster Hushpower on a 6.2 super duty? I have the muffler out now and hate the sound it makes at 2.5 rpm. Just wondering if it gives a deep tone and if it works for the drone sound in the cab.
View 5 Replies
I read in a thread about how fog lights need the auto light sensor or something in the kit to be installed and flashed.
My truck is a 2012 f250 XLT that I bought left over from a podunk town IN illinois. It does not have fog lights but it Does have automatic head lamps. So Im very confused on what kit to order to add fog lights to my truck.
View 3 Replies
I've got a 2012 XLT that I would like to add remote start to because I'm tired of getting into a truck that feels like a freaking oven.
From what I see on Ford's site, looks like this should work:
[URL]
Are there any aftermarket systems I should be considering?
View 14 Replies
Have an 08 f350 xl and was looking to put oem foglights into the bumper where mine has the block out 's, guess what I am asking is if the wiring is already there as it was on a different vehicle I owned ,basically it was a plug and play ,have only had the truck for a week and with the hours I'm working I really haven't had a chance to crawl under and look for the wiring.
View 3 Replies
I would like to add a second backup camera to my 2016 F-350 Super Duty to assist when hooking up to my fifth wheel. It is a Crew Cab with the Factory Tonneau Cover so my view of the hitch is blocked. I would like to add the third brake light high mount camera and be able to toggle between my OEM/Tailgate Camera and the High Mount. I have found a couple that claim they will work but both require tapping into the main connector on the back of the display, but not quite sure how to open it up. Accessing the connector is not a problem, just getting it apart without breaking it is the question. The "Lockpick" system has not been tested/certified for the 2016 model.
View 3 Replies
Had the DEF 500 mile warning come on last week. Second time for this. First time early on when it was new. Put a 2 1/2 gal. container of Blue DEF then and all was well. This time I did the same thing but keep getting the 500 mile warning afterwards. Cancelled the warning a couple of times , and now I am getting a warning that I have 378 miles left on the DEF fluid remaining. Its like the truck didn't recognize me adding the 2 1/2 gal. Also the check eng. light is on now. Thinking thats related. 7,000 mile on truck
View 3 Replies
This has been beaten to death but all the old threads I read are for 2011 to present SDs so I wanted to make sure I can add these to my 2008 before I spend $ on the switches. Anything I should look out for on the install? Once they are installed I would like to add front and rear strobes along with a roof light for plowing.
View 3 Replies
I just put some toyo at2 295.75.16. On my 04 250. And I've got some rubbing on the plastic and front leaf springs. If a 2.5 " spring left will take care of the rubbing or will I need wheel spacers.
View 3 Replies
This is probably a strange request but I did just get a 2011 F250 XL. The SYNC and audio controls on the steering wheel was an available option, but my truck does not have it. I didn't ask for it to be required in the vehicle search, just one of those "if it has it, awesome" things. I am looking to add the buttons to control the radio and MAYBE SYNC for the bluetooth feature if this is possible.
I know to add SYNC I need a radio that's ready for it, which mine is, and a microphone somewhere and all of that so that's not to be done until a later date. My old F150 had the radio controls on the wheel and I miss that. Can I add the radio controls on the wheel? And maybe SYNC without needing to add a Parrot device for bluetooth? Or am I SOL on both?
View 10 Replies
