I have a 4 inch lift on my truck and currently have 20x10 with 35x12.5 but I want to run a 20x12 with a 35x14.5 or maybe just a wider tire on my 10 inch wheels but idk how much bigger I can get on a 10 inch wheel
View 14 RepliesThis is probably a strange request but I did just get a 2011 F250 XL. The SYNC and audio controls on the steering wheel was an available option, but my truck does not have it. I didn't ask for it to be required in the vehicle search, just one of those "if it has it, awesome" things. I am looking to add the buttons to control the radio and MAYBE SYNC for the bluetooth feature if this is possible.
I know to add SYNC I need a radio that's ready for it, which mine is, and a microphone somewhere and all of that so that's not to be done until a later date. My old F150 had the radio controls on the wheel and I miss that. Can I add the radio controls on the wheel? And maybe SYNC without needing to add a Parrot device for bluetooth? Or am I SOL on both?
Have a 2008 F-350 crew cab 4x4 lariat with 20" wheels on it. Tire size is very limited/expensive. Can I replace the 20" wheels with 18" or 17"? I was told it depends on the size of the brakes. How do I check that, short of buying "test" wheels? I am old school and would rather have more tire and less rim, than the other way around.
View 14 RepliesI'm planning on doing a 2" level. Will I need a drop pitman arm, or can I stick with the stock pitman arm? Will I need anything else? I plan on doing the level when I replace my coil springs and shocks. (I have another thread on that). I'm driving a 2000 F250 V10 2WD CC SB (twin I-beam front axle) if that info is pertinent to this question.
View 2 RepliesI am trying to get an extra set of wheels for my truck before we move back to Alaska to mount my studs on next winter. I have found a few used sets but then realized I have the tire pressure sensors on my truck. If I pick up a set, do I have to get ones with the sensors? Can sensors be added to the tire shop? I just really have no intel on this subject!
View 8 RepliesMy 1999 SD was originally a Work Truck without cruise. I'd like to add cruise of some sort (factory or after market), but also trying to keep the cost and difficulty factors low.
Have any of you SD drivers ever done this and if so, what you went through?
I want to put in a SPD Y pipe. They make 2 different ones, 99-00 and 00-04. I have a 2000 and so I've been trying to figure out which one. The SPD website's phone number goes straight to voice mail and it's inbox is full. 5 star tuning who sell's these as well told to me to just "get under the truck and see"... I'm no exhaust pro so I don't know what to look for. I just went to a ford dealership and their diagrams where the same but it did show there were different part numbers for the two different styles, so they couldn't work either. It says on SPD's website that the exhaust configuration changed somewhere in 2000. So, what to look for in the difference. Maybe a picture of a 99 y pipe and 01 y pipe would work?
View 11 RepliesPutting a FLowmaster Hushpower on a 6.2 super duty? I have the muffler out now and hate the sound it makes at 2.5 rpm. Just wondering if it gives a deep tone and if it works for the drone sound in the cab.
View 5 RepliesI have a stock 2012 F250 6.7 Diesel. I was looking at getting new 18 or 20 inch rims for it and was wondering what the largest tire I could fit on those without rubbing on the truck would be. I know there are lots of topics on this but I could not find anything that applied to me. Most topics were on stock wheels.
View 1 RepliesI read in a thread about how fog lights need the auto light sensor or something in the kit to be installed and flashed.
My truck is a 2012 f250 XLT that I bought left over from a podunk town IN illinois. It does not have fog lights but it Does have automatic head lamps. So Im very confused on what kit to order to add fog lights to my truck.
I would like to add rear overload leaves to my 2016 F250 that for some reason I didn't order with the camper prep package. From what my internet research tells me I will need to add the frame tabs and rubber bumpers, the overload leaves themselves, and of course longer U bolts.
My question is, in all of the pictures I can find, there in an intermediate spacer block between the regular leaf pack and the overload leaf. I can find a part number for this block ( 2C3Z-5594-AA ) only for 2002-2007 trucks. The parts diagrams I've seen online at various Ford sites don't list a part number for this block on current model trucks. Most just give a single part number for the whole leaf pack.
For 2014-2016 F250 with the camper package, or an F350 know what part numbers I might be looking for? Do the newer model year trucks still use an intermediate spacer block? Any chance someone with one of the aforementioned vehicles can post a picture of what the overload leaf setup looks like on a new(er) truck?
I would assume if you snap an overload leaf you can get a replacement from Ford, so why can't I find a part number for them either? I'm pretty sure I will have overloads built at a local spring shop anyway, but at least want to make sure I'm matching the correct and current factory setup.
I've got a 2012 XLT that I would like to add remote start to because I'm tired of getting into a truck that feels like a freaking oven.
From what I see on Ford's site, looks like this should work:
[URL]
Are there any aftermarket systems I should be considering?
Have an 08 f350 xl and was looking to put oem foglights into the bumper where mine has the block out 's, guess what I am asking is if the wiring is already there as it was on a different vehicle I owned ,basically it was a plug and play ,have only had the truck for a week and with the hours I'm working I really haven't had a chance to crawl under and look for the wiring.
View 3 RepliesI would like to add a second backup camera to my 2016 F-350 Super Duty to assist when hooking up to my fifth wheel. It is a Crew Cab with the Factory Tonneau Cover so my view of the hitch is blocked. I would like to add the third brake light high mount camera and be able to toggle between my OEM/Tailgate Camera and the High Mount. I have found a couple that claim they will work but both require tapping into the main connector on the back of the display, but not quite sure how to open it up. Accessing the connector is not a problem, just getting it apart without breaking it is the question. The "Lockpick" system has not been tested/certified for the 2016 model.
View 3 RepliesHad the DEF 500 mile warning come on last week. Second time for this. First time early on when it was new. Put a 2 1/2 gal. container of Blue DEF then and all was well. This time I did the same thing but keep getting the 500 mile warning afterwards. Cancelled the warning a couple of times , and now I am getting a warning that I have 378 miles left on the DEF fluid remaining. Its like the truck didn't recognize me adding the 2 1/2 gal. Also the check eng. light is on now. Thinking thats related. 7,000 mile on truck
View 3 RepliesThis has been beaten to death but all the old threads I read are for 2011 to present SDs so I wanted to make sure I can add these to my 2008 before I spend $ on the switches. Anything I should look out for on the install? Once they are installed I would like to add front and rear strobes along with a roof light for plowing.
View 3 Replieswant to raise the front of my 99 f250 super duty. I only found rough country for my options. I am looking for a 2-3" lift. Will the 3" lift spindles work fine? What else am i going to need? Shocks?
[URL].....
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesMy 99 250 XL only has heat, and the blowthru vent air which in Florida, might as well be heat also. LOL.
Since the vents and everything is there, what all and how hard would It be? I have an extra dash control that I can put since mine doesn't have the ac option on it
I have a 2004 F250 and would like to have more light in front of me. I looked under the front to where the stock fog light would get mounted but I don't see any wire harness in that area. What is involved if I pick up a pair of replacement fog lights like the offer at LMC Truck. Would i need buy a harness? And what about a switch?
View 11 RepliesI used to own a fleet of school buses and I had remote trans filter on all of them. I'd change the filter about every 10K and felt like it really extended my trans life on Allisons. I wanted to put on my SD, so, I had a spare filter block with a 20psi bypass valve, and I used it. Worked out real well mounted to the radiator support, up front--easy access. uses a NAPA 1268 filter. In the picture it looks like the hoses are real close to the AC condenser, but in real life, the are three inches from it.
View 2 Replies