Last week the ABS light comes on and will go off after a short drive. Obviously the Scanguage II does not read the code. I have replaced both front hubs last year and have less than 6k miles on them. I have checked the connections, and are good. I changed diff fluids around the same time as the hubs.
View 1 RepliesI have a 1999 f250 7.3 ... l extended cab 4x4 super duty ... ABS light on, over drive light flashing and speedometer has stopped working .. I have replaced abs senor on the rear of transmission and on the rear end.both new and just replaced abs module just the computer not the pump that was used . And abs light, overdrive light are still on and the speedometer is still not working ..
View 14 RepliesI have a f350 2000 4x4 automatic 170.000 miles. Service light on and OD light flashing. I have code p1747 "EPC solenoid short circuit"
This code make that the engine runs slow without power and hard shifting. I change all the solenoid body and check all wiring.
Later using a voltmeter i separate EPC solenoid wiring and see that have 5 volt. If I don't accelerate more 2000rpm OD light is not flashing and truck works normal but slow.
When I accelerate more than 2000rpm OD light begin to flash and transmission fail more. I check that EPC wires mark about 0 volts when OD light is flashing. Transmission hydraulic system seems to be ok because oil is very red and clean. Maybe another sensor is making this failure....
When on my 2-post lift my front brake lines on my '11 4x4 are pulled TIGHT, like stupid tight. It's also dumb that the soft line points UP 'cause it gets tugged down to a brutally tight 180.
I've got the front lift pads under the control arms, too, but near the very rear of the control arms so the axle isn't even dropped out all the way I don't think.
There's a bracket down near the bottom of the coil springs that could just be sectioned/lengthened, which I think would alleviate my issue. I'll be working on this soon.
What manufacturer builds a vehicle that yanks on the brake lines under full suspension droop? Shouldn't this be on an engineer's final checklist before the vehicle is released? Oh wait, they gave that task to Team TTB and Engineering Group TFI Or maybe they gave it to the same Audi team that designed the Allroad with airbags that can be damaged if you don't "lock" them out before lifting the vehicle......
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI installed an aluminum flatbed on m 2004 F250 5.4 and when I was wiring the lights, I accidentally shorted the marker/running lights to ground. The fuse is not blown (17), the dash lights come on. I have checked for power to the other lamps and there is nothing. I am looking for any information that would lead where to look for the cause.
View 10 Replies1999 F350 7.3TD auto 4x4 crew 8'. I've noticed that I get a soft, low, short grumble from the rear end when leaving a stop with a load.
My son just used the truck and says he thinks the rear is binding while in reverse while backing into a parking space, wheels turned.
What are the potential problems here? I've heard a fluid change with "anti-slip additive" could be the answer. Which anti slip additive should I use?
While pullin in my 7.3 with a 4r100 from a passing hail storm, i shut her down and crawled under it just to check things out. While under there I heard a noise that sounded like something was shorting out figured out the location of the noise, but what the electrical connector is for?
passenger side next to exhaust
After further analysis the noise only happens after truck has been placed in drive gear and then to park gear and finally shut down/turn engine off... Makes noise for around 30 seconds and is not a constant short noise like something is jumping around....
More pics about the problem that is hard to get too and explain where it is...
Just behind the tranny line....
Windshield wipers, and washer were suddenly not working the other day, so I discovered a blown fuse. Put a new one in, and it immediately blew again. So there is definitely something grounding out, and I am suspecting the wiper motor itself because so far I have not been able to find any wires shorting out, but before I go to the trouble of pulling the motor out and testing it, or replacing it.
Truck is a 2002 F350CC 7.3 TD. Wipers were working fine the other day before I pressure washed it, which is why I really suspect the wiper motor itself.
6.2L F250 truck is just shy of 60k runs good however on cold startup there's now a pretty loud ticking noise for a short period (30 seconds) until it warms up then it slowly goes away. Once its warmed up there isn't much of anything.
Did these have exhaust manifold gasket problems like the 5.4? Hoping that's it if not, any other common problems that would make that ticking noise and then go away quickly once the engine is warmed up.
I've been tracking down all sorts of issues in my Excursion 4x4 lately and I have a few questions. I have an issue where everything is spinning as I drive even in 2wd. I gutted my hubs and removed the driveshaft. I had new u joints put in the front shaft today and re installed it. I still have the same issue of everything spinning while driving in 2. I had my marks move with the shaft in or out. I assume its getting toward front axle joint time. The shop owner said there should not be any movement in 2 but every SD I've seen has the axles spinning driving around town. I'm just confused because I have the entire driver side axle move when I spin the shaft by hand.
View 11 RepliesJust got my torque app running. At idle I am seeing ect of 186.8 and eot of 176.8. After driving around town for about 30 minutes. Are these acceptable?
Note: ambient temp is 22F
Checked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 RepliesWhen I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 Replies1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
have a 2006 Forest River Lexington 255 GTS on a Ford E450 chassis. We purchased it used 2yrs ago from a private owner with only 20,000 miles. It had a slight vibration which got worse over 60 mph. All tires were replaced and when that didn't work, took to a different dealer to have road balanced. We drove the home some and the vibration got worse starting about 40 mph. We took it to a local truck repair shop that does drive-line work. They have replaced the transmission tail housing with a bearing it, had the drive shaft rebuilt including new u-joints and re-tubing the front driveshaft. The vibration now is worse than ever..so bad that it's not drive-able over about 30 mph.
View 7 RepliesToday I noticed that our 5R110 was delaying slightly when shifting from drive to reverse. It was probably about a 1-2 second delay but it replicated itself twice in a row. There was no delay going from reverse to drive. It is just an engagement delay. We are running a Superchips Heavy Tow tune on the truck, it is a 2006 6.0 Powerstroke.
View 4 RepliesRecently purchased a 99 F250 SD w/ V-10 Triton which purrs like a kitten and drives great until I turn it off and then re-start. It has trouble re-starting and then when started and put in drive...won't go anywhere. Zero power. Oddly, in reverse it goes. Getting decent flow from exhaust. No vacuum leaks I can find. No check engine light on either. Strange.
View 7 Replies1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
Not sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
So after eight years my Warn premium hubs have taken a crap and developed major play internally. After speaking to Warn warrenty department and sending videos they will replace them according to the lifetime limited warranty. Problem is they sill not send out new ones until they receive the old ones, so I was told from time i remove mine and send them back and get the new ones it will be two weeks maybe a few days more, there is no snow in the extended forcast and im wondering what damage could occur with me funning the truck everday to work etc with the stub shafts just hanging there?
View 14 Replies