Ford Super Duty (1999-2016) :: ABS Light Came On After New Wheel Hub Assembly
Jan 8, 2014
I just put a new front driver side wheel hub assembly on last week and i discovered two things. The metal plate that goes in behind the wheel hub assembly needs replaced but idk what it is and i need a new axle seals. But when i put the new hub assembly on, the abs light came on and i cant seem to figure out why? Also my front drivers side of the truck is still making a clunk noise when i hit a bump. Input on that too?
View 6 Replies
Advertisement
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 Replies
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 Replies
My blower assembly (not at the blower but in the box below it) is filling up with water. Any way to look into besides drilling a hole in the bottom of the box?
View 1 Replies
Today I noticed a leak at the heater hose assembly at the right rear of the engine compartment. It appears to have special connectors and that appears to be where the leak is coming from.
View 1 Replies
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 Replies
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
I have a 2000 F450, 7.3, 4x4, dually, VIN 1FDXF47F0YEA44380, with 30k miles, That needs a new rear axle - hub retainer threads on axle housing are stripped (nut welded on by previous owner). This axle is a case ID F81A-4001-BK, 4.88 ratio, 11.25 ring gear, with a 41.5" spring center. I have heard that the '99-'02 axles had issues until Ford switched over to the later square housed axles in 2002 or 2003 (Dana 110, I think). Is it possible to adapt these later (2002- 2004) axles onto a 2000 F450? And if so, what would be involved?
View 3 Replies
So there I was doing a simple oil change and when I took the filter out I noticed the little spring on top, in the center of the big spring (oil filter adapter) cocked to the side with the little plastic piece broken.
does anybody know if I can replace just the oil filter adapter (spring thingy that goes in the middle of the filter when installed) or do I have to replace the whole filter bowl assembly? And if so where would be a good place to get this part?
View 5 Replies
Heard a thumping yesterday as I'm getting on the highway at rush hour. I looked in the drivers mirror and I see my rear wheel flopping around. I had sheared off 6 of the 8 studs. After towing it home I pulled the wheel and tapped out the broken studs. I've never done this before so I'm a bit unsure as to how I get the new studs in. The drum brake assembly is behind the rotor and even if I pulled all that out it still doesn't look like I have enough room. Did I just discover this job is bigger than I thought?
View 6 Replies
So just as I think I have it figured out what size tire and wheel combo I want to go with, I began thinking about going from an 18" wheel to a 17". I can save some cash, have a few more tire size options and save on tire weight.
I know alot of guys go up to a 20" setup but that's just not my preference on trucks.
Any negative to doing this? 315/75/17 tire size interests me. Had that on a Wrangler and liked the look. Going to look a little more at 17" sizes before deciding.
View 11 Replies
Checked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 Replies
When I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 Replies
I seem to be having a issue on take off with my new Super Duty, it has the michelin atx2 tires than come on these trucks. On any hill or grade on take off she just spins and traction control flashes on dash, what the heck? Do I need to pull out the 4x4 switch to engage the e-locker so this thing will move? Seems crazy to have to put her into 4wheel when there is only a inch of snow on the ground... My 6.0 did this sort of due to all the torque it had, but that had those crap Contitracs on it till I swapped them for BFG at..
View 14 Replies
Recently bought a 2015 f250 xlt.....very impressed with it. Only thing is the wheel feel and look to small. What is the largest size i can run stock? Will 35/12.5 fit on stock 17 wheels or should i just spring for aftermarket rims at the same time? Also exhaust options for the 6.2? Remember, i need load range e!
View 4 Replies
I recently bought some used rockstar 1s off a buddy, installed new tires, balanced, put tapered lug nuts on and I'm still getting a slight vibration above 40mph. Do I need hub centric rings? XD says no, I think I do.
View 2 Replies
Got a problem with my F350 diesel truck's braking system. I pull a 5th wheel and last trip almost burned my breaks up coming down long hill due to having no breaks on the 5th wheel. Had a problem early on with the lack of trailer brakes and module was replaced under warranty. Bought a new module this time and it did not fix the problem. Have braking power when I use the module brakes (Hand) but not when I hit the foot brakes. Have checked the system with a meter and have good voltage with hand break but not with foot brakes. Have a good meter (voltage) read with hand breaks and faint read with foot brakes applied. Also have a faint pulsing read on test light with no brakes at all just key on.
View 2 Replies
the mechanism that locks the steering wheel is stuck. not the ignition key cylinder (already removed that). how do I release that mechanism to free the steering wheel.
View 3 Replies
I have a 2004 F250, CCSB, 6.0L, Fx4, Lariat.
I am trying to replace the passenger side front hub. I either have a bad hub, or I am not installing it properly. I have it installed with the locking hub unlocked and trying to turn the hub, the entire passenger side axle spins. It is also very hard to turn it. I strapped axle, and the hub is almost impossible to turn, with or with out the actual hub installed.
This is the second hub that I installed with the same results. I''m not ruling out bad out of the box, but it is the second one I installed today.
View 10 Replies
If front wheel bearings can be greased through the abs wire hole on a f250 4X4, will that work on a sealed bearing on a gm product? I have done my f250 but I also have a 2004 suburban.
View 2 Replies
So I was backing in to my space at home last night when I hear this loud pop come from the front left. This morning when I left for class, I pulled out and it did the same thing again. I go out and looked under and behind the tire and nothing looked broken or caught.
I watched my tire as I turn the wheel. When I turn to the right, just as the wheel gets maybe 10-20 degrees past straight, it hangs up on something and the wheel pops and releases and continues it's motion. Then as it comes back to center, it hangs up in the same spot and finally breaks free and continues back to center. When it frees up on the return to center, the front end drops some, which makes me wonder if it's something with the suspension. The suspension is old and sags pretty low (I started a thread on that earlier).
While I'm driving, when I turn right, The Pop will happen, but will not pop when I straighten back out. then when I come to a stop, it will free up when I get to about 10mph, and the front end of my truck will literally jump to the left.
Needless to say, I drove home and parked my truck, where it will stay until I can figure out what the heck to do. What it might be? I'd prefer to fix it myself if possible. Its a 2000 F250 V10 2wd. I just replaced the front left caliper a few weekends ago, and the front left inner and outer tie rod end about a month ago. I had it aligned after the tie rod end, and now it is considerably out of alignment. the wheel sits about 45+ degrees to the right of center when I"m going straight.
I am extremely frustrated because of all of the stuff that has been popping up since I bought the truck. When I have the chance to go home in a few weeks after school lets out, the truck will be going straight to MY mechanic to have it looked over.
View 14 Replies
