Ford Super Duty (1999-2016) :: 5R110 Transmission Would Suddenly Hard Shift
Sep 7, 2017
I have a 2005 Ford 6.0L Diesel with the 5R110 transmission.
About a month ago, i started seeing some strange shifting issues with the transmission. While driving normally, it would suddenly hard shift (slam itself into gear), the entire truck would shake it shifted so hard. It would also cause the Tow/Haul indicator to start blinking. (my understanding is that the Tow/Haul light indicates an error code).
I drained/flushed the transmission, installed the larger pan/with the improved filter. I put Mercon LV back into the transmission (what type of fluid was in there before).
The problem still persists, and got a bit worse. The truck is almost un driveable at this point. Still getting Tow/Haul flashing messages. Can the error code be read by an standard ODB2 reader ?
View 9 Replies
Advertisement
Iv got a 2003 6.0 stroke with 212k miles on it. Runs like a top. Done a slew of work from injectors to hpop, 2 alternators, intake, exhaust. NO tuner! Stock. Anyway recently I started the old girl up, warmed up a bit and shifted into reverse and truck did nothing. Went to drive and same thing. Held brake and revved it up and it dropped in gear. Shifts fine after that. No issues other than the occasional NO shift from park problem. Iv dropped pan and replaced all filters recently.
View 2 Replies
My '01 recently seized up and a buddy determined it was the AC pump. Replaced the belt with the bypass version. A month later, I moved across the state to Iowa. A couple weeks into living here I turned the truck on and it was idling really high (about 2500-3000) but would settle down to around 1100 when put in gear. However, shifting into gear is causing a progressively worse "jump" into gear. Hadn't really had the money or the time to take it in so I let it mostly sit unless I absolutely needed the truck.
Today, the idle is still high and does seem to cycle a bit in that it will rev up close to 3000 then settle back down around 2200 or so and then rev back up again and so on. I backed it down the drive into the sun for a little warmth and it darn near jumped a foot when I shifted. I turned the heater on defrost so I could clear the windshield and absolutely nothing came out.
I can't get into a garage for a few days to get it hooked up for diagnostics. So I thought I'd try here. My research leads me to think part of my problem may be a vacuum leak and/or maybe a sensor somewhere.
View 4 Replies
Last week our F250 suddenly stopped running. We had it pulled to the house, about 2 miles, and found it was the AC Compressor Clutch (took belt off and it started fine) Today we replaced the AC Compressor and now it wont shift into drive. Reverse is fine, fluid is fine and there is no warning lights on.
View 13 Replies
Started flaring between 3rd and 4th I changed the pressure solenoid and the direct clutch and no change. Flushed the tranny and changed filters and no change the oil is not burnt. When it flares it goes into a safe mode on the dash and will shift perfect through 4th gear no issues. I guess I've always know if it's bad it's bad but I don't understand why it works in a safe mode but slips in regular. Also if it is a bad tranny will a 3c2p-7000 work as a swap in my truck. 2008 6.4 4x4 ....
View 5 Replies
I have a hard shift between 2-3 that is somewhat violent. It doesn't matter the rpms or how hard I'm accelerating, it will always do it. At wot, it sometimes throws a code that stays on for a few minutes, then goes away. When I hook up a code reader, it shows no record of it and it never throws a blinking OD light ever.
It has an ATS transmission, but I don't know how the controller works, if it is wired correctly, or if it could even cause this issue. Currently the truck has 210k and unknown on ATS.
View 2 Replies
The truck belongs to a very good customer of mine and is a 05 f350sd 6.0 td with 5r110 torqshift tranny. The vehicle presents with these symptoms and codes....
-there is a delay from p to r and its intermittent, sometimes it will be in a weak reverse where it wont creep unless you give it some gas, sometimes it will hit reverse hard after this. sometimes it bangs reverse
-there is a delay into drive intermittently with the same symptoms as reverse where sometimes it bangs and sometimes it will take a little throttle to get it moving
-once the trans is hot (operating temperature) it has trouble downshifting. my solus tells me sometimes it tries to start off in 3 or 5 then sometimes it will bang back down into first and almost chirp tire with little throttle input
-tow haul light will flash after several miles and then it only has 1-2-3-4 no 5-6. then the starting off symptoms get worse
-throws codes for
p0766 shift sol d performance/stuck
p2701 friction element b apply time range/performance
p2703 friction element d apply time range/performance
p0700 trans control system fault.
So far the ideas i have are as follows
replace solenoid D
direct clutch replacement and seals for corresponding drum
torque converter replacement and pump replacement
harness rub through between pcm and transmission
The truck has had similar issues a year ago. Upon testing line pressure i found it was out of spec and replaced the epc. (electronic pressure control solenoid) and this cleared most of it up . I have had the pan down many times and the fluid has not been burnt and there is little debris in the pan. nothing i would consider beyond normal wear. Tomorrow I will be dropping the pan again to inspect the magnet and fluid as well as the condition of the harness. i will post my findings at that time. I am hoping between now and then some of you will be able to point out a few possibilities to get me on the right track.
View 14 Replies
I have an 01 f250 with a 4r100. Trans has not been slipping at all and yesterday it started a rough shift between 1st and 2nd. (3-4K Rpms) At the same time 4th gear stopped engaging. Shifts out of 3rd but does not go into 4th. I can hit my od button and it will shift back into 3rd and start pulling. Still no slipping just doesn't want to change 1-2 or engage 4th. I have done a full trans fluid change including new filter and tc. Old fluid looked fine with no metal flakes or garbage in it. So all new fluid still same problem. I was thinking of changing my shift solenoid.
View 9 Replies
2015 F 250, less then 5k miles. When towing travel trailer, weight 7500lbs, on occasion transmission will not shift out of gear. Happens in first, second, or third. Very intermittent. Take off from a stop engine goes to 6k rpm. Let foot of the throttle goes all the way back to idle, still no shift. Accelerate back up to speed still will not shift. After doing this a couple of times finally shifts. Have had this happen in second and third. Not a lot of fun with cars behind you or trying to merge on highway. No codes
First trip to Ford dealer they re calibrated computer. Still happened towing. Second trip to dealer they put a flight recorder on it and I towed again. Did not hang up in first or second ,but would not shift out of third on highway doing 70mph, even when I lifted from the throttle and coasted. I finally shifted to manual and shifted to fourth and was able to upshift After reading flight recorder mechanic said it appeared normal. I explained that having to shift the transmission manually is not really normal and they agreed.
View 14 Replies
2014 F250 automatic- 35k miles... just started having an issue. Noticed when the transmission is cold, the shift from 2nd to 3rd is almost delayed. It's enough of a pause you can feel it then it shifts. Weird thing is it only does for the first 3 stop signs leaving my house. Once the trans starts getting some temperature to it, it shifts perfect. I checked the fluid while hot and it showed a little low. I drove it after adding fluid but will have to wait till it's cold to see if it's any better... Think it was the fluid? But why just 2nd to 3rd gear only?
View 3 Replies
So, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
View 3 Replies
I go out of town for work for a week and come back and my 1999 F250 V10 GAS, is acting up. It started when i tried to drive it and it didn't want to shift, it would rev up to 3000+ RPMs and finally shift really hard into gear along with the speed odo not keeping up and bouncing around not wanting to work. I also had my entire gauge cluster lit up with no key and door closed. all the lights were on and it was "dinging" like the door was open and it wasn't. you would hear it when you put your ear up to the door.
So my first thought was to change the VSS (which I did) no luck. So I started wiggling wire loops under the fuse box in the cab and the "dinging" quit.. i took it for a drive and it works like nothing ever happened. Obviously I am guessing there's a short so i brought it to my mechanic and hes saying he couldn't find anything by the fuse box but he thinks its closer or even attached to the gauge cluster itself. could this be true? Why would the gauge cluster loop throw off the shift points?
View 5 Replies
I have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 Replies
The tranny is shifting really hard between 2 and 3 if I feather the throttle it can be a little less of a jolt but still enough none the less iv never done a filter and fluid change as I just got it it has 235000 miles 99 v10 super duty 4x4....
View 8 Replies
Recently I have had an issue with my auto which was just rebuilt. About 500 kays after i picked it up it shifts dangerously hard and immediately into all gears at around 20-40 mph, converter also locks immediately. The speed sensor in the box was replaced with the rebuild but I'm having it replaced again this thursday just in case.
Just for the record I cooked it on the beach a while back, the speed sensor was replaced with the rebuild as it was doing the above, the od light also flashes when this occurs, before and after the rebuild.
Prior to cooking it never had an issue.
What could be causing it? I'm starting to worry it cant be fixed, have done a google and tried a couple of things mentioned. Code says wiring issue associated with speed sensor in box.
View 8 Replies
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
View 1 Replies
I have a 2004 f250 5.4l w 4r100 and it seams to loose its gear or down shift only when i take a hard right turn. I took it to a trans shop and it shows no codes and at this point I am very confused...
View 9 Replies
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 Replies
I have a 2011 F250 with the 6.2 34000 miles and my Transmission shifts hard between 2-3 and 4-5 took it to the Ford dealer and they said it is the shift solenoids are bad but it is cause from the Powertrain Control Module and its not covered by the warranty because it is part of the emission system.
View 4 Replies
I have a 1994 F-250 XLT heavy duty model. No warning lights are on. A few times a month my transmission will start shifting hard, kicking into the next gear. The odd thing is, if I reset the computer it stops. Shifts smooth as butter. The fluid is a vibrant red and the fluid looks great like it's new. What is going on? I'm getting tired of having this happen. The truck has 108,500 miles on it.
View 10 Replies
I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 Replies
