My 4x4 on my 2000 model f350 will not engage. The light works, comes on briefly on startup of the engine. When I flip the switch nothing happens. When I jumper the relays nothing happens. I do not have the factory hubs, they r warn hubs and the vacuum line to them is capped off. How to figure this out on why the 4x4 will not engage?
View 13 RepliesI have a 2002 Ford Superduty. I recently had installed a BDS 8 inch suspension lift. I also had the upper and lower ball joints replaced. All this work was done by a certified garage. Today i went to pull out my boat from the ramp, turn the switch inside the cab to 4x4 high. The light came on but 4x4 did not engage. As i pulled the boat out of the water the rear tire spun in the sand but the front did not. As i cleared the ramp and on level ground i turn the switch off and back on i heard not but the light can on. With the 4x4 light on i turn the wheel and pulled forward i noticed no hopping as when a truck is in 4x4. Initially when i turn the 4x4 switch on i hear a clunk up front but not after. Drove home drive train appeared fine no noise.
View 3 RepliesLong story short: I bought my 2003 F-250 super duty 6.0 used back in January. It had one Ford OEM battery and one Walmart special. I had them tested and they were both completely flat. Replaced the set of batteries the next day. Since then, upon cranking the truck, the battery indicator will be illuminated while the truck is running. It will stay on for a length of time that varies based on the day. It will eventually turn off after driving a while, but will come back on if I kill the truck and crank it again (like when running to a store).
The batteries have been tested 4 times and test just fine. No problems with the batteries. The OBD 2 computer/monitor I have installed reads a voltage of around 13 when the truck is running. What to do to solve this problem. It isn't a major issue as the truck always cranks fine and the batteries are not damaged or anything, it is more of a annoying thing. It bugs the crap out of me.
2012 6.2 XLT 50,000 miles with manual single zone controls. I haven't had time to work on it yet, but it seems that my AC compressor is not engaging. The dash controls light up normal, fan comes on, etc. I am just looking to see if there are any common failure points. I know it COULD be low on charge, clutch could be bad, etc. I am just checking if there is a common failure with these trucks AC system.
View 10 RepliesI would like to know what's happening, it seems as if idling for a minute to let my transmission temperature dial raise past the lowest line on the dial fixes or at least drastically reduces a couple issues.
The truck will deliver power much smoother off the line. I've been concerned about this for a while. The degree to which it happened wasn't constant but it seems like the truck is having trouble grabbing on (so to say) to the power coming off the line. I sort of liken it to a rope. When I give it the beans the rope goes forward but it takes a half a second or so for the truck to "grab" on to the rope. Never hard shifts, it's just delivering the power off the line or from a near stop.
Idling for a minute seems to fix this, power delivery is smooth off the line. Transmission dipstick was nice and pink but smelled slightly burnt. This is with the engine cold overnight. Didn't have time to do multiple wipes or check in the handbook for the proper methods of checking fluid, I just pulled it out quickly to take a look before heading out. Fluid covered the whole tip.
Second issue that seems to be fixed is that the battery light doesn't come on nearly as much and not for nearly as long. Typically the battery light will come on and off seemingly on its own whim during the drive. However, it seems to stay more consistently off if I idle right after startup.
Now bear in mind I baby my truck, I don't rev it high right after startup. Just low enough to cruise around the parking lot until I hit the road then I accelerate up to 40 - 60 depending on my route. I'd gladly give it the minute to warm up in the future but if I could get down to the bottom of this that'd be preferred, I doubt this is required behavior.
I do realize that these issues are not tied to startup behavior but I find it interesting that idling for a minute at startup to let the transmission gauge rise seems to mitigate these symptoms.
Pump works fine. Replaced pvh. Won't go into 4wd hi or lo no matter what I try. Even with them in lock. How do I know if hubs need replaced or just hub locks?
View 2 Replies2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
Truck was running fine up until now. After the WTS light goes out, I crank it and.... nothing. It doesn't even try. It's not a battery problem. I have 12.6 V from each battery before and after cranking. The lights are bright, the horn works, the dash lights are strong and bright all both before and after cranking. It just doesn't want to engage the starter. I tried my backup key as well, thinking it might be a problem with the PATS. No dice. Where to start looking?
View 6 RepliesI'm trying to figure out why my auto locking hubs do not engage. To isolate the problem shouldn't the hub engage if a vacuum is applied to that hub only? A solid 18 inHg is maintained at that hub for over 10 minutes but the selector will not rotate, which suggests to me the seals are OK. What then might be the problem?
View 13 Replies2006, ESOF. Noticed the front hubs aren't engaging but the transfer case is. What should I check?
View 3 RepliesABS light has been coming on intermittently the last few days. Checked the resevoir for fluid level...topped up a bit. Changed the oil today and looked at the sensor connectors on the front brakes...ok... Got a new speed sensor and installed it....ABS is still on. Checked the old sensor with my meter and it is open circuit....no continuity, so I'm thinking it was the problem.. Is there something that has to be reset for the fault to clear, say with a code reader etc?
View 9 RepliesI have an 06 F350 with the 6.0 powerstroke. My battery light started coming on and will go out for a while, then come back on. Sometimes it flickers a little. I have checked/cleaned battery terminals (there was no corrosion). I have replaced the alternator. The batteries are just over a year old (10/12). I have not had any slow starting or any other symptoms other than the warning light. I am still having the same problems after replacing the alternator. I have checked with a voltage tester and it was reading 19+ when the light was off. When the warning light is on it was jumping from 12 - 15. This is an old tester so I'm not sure that it is working correctly. (not sure why I am getting the 19+). I'm going to go buy a new tester, but I was wondering if there is something else that could be causing the warning light. I know very little when it comes to electrical issues.
View 6 RepliesGot in my truck this morning and everything worked fine, no problems. Arrived at my destination and parked. Come out about two hours later start the truck and my A/C wont blow air, My truck is an 05 lariat so it has the climate control A/C. Everything was working fine it just wont blow air, When i turned the A/C on and off i could hear/feel the small thump of the clutch engaging on the compressor. I am thinking the blower fan just went south? or maybe something stupid that controls the blower fan? Summer is in full swing here in central florida, temps are 95+ not including the humidity...
View 14 RepliesMy 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 RepliesI have a 2001 F250 4x4 and the ESOF switch not engaging hubs, currently I have no 4x4 lights coming on in the cluster when i turn the switch. I am not experiencing any of the vaccum symptoms that most people are suggesting. I When I turn the switch i also do not hear any relays clicking. Relays have been tested, and i waited for the 45 second transfer delay that the manual mentions. ESOF switch has power, and is working properly (I know because I bought a new one in attempt to fix the problem) Basically I have no responses from any of my 4x4 indicators or parts.
View 14 RepliesI have a 6.0 and the air filter light keeps coming on and going off periodically, it seems like the engine is missing bad at times, runs better when tow/haul is on. I am not picking up and codes when I put it on the scanner. I'm possibly thinking injectors.. a friend of mine said something about checking out the "PCM"?
View 4 RepliesNeed to know of an issue that causes the stability control light to come on for no apparent reason? I took it to Ford, they said no codes found and they replaced an ABS sensor, less than 5 miles after leaving, sitting in stop and go slow moving traffic it comes on again. I've been taking pictures to show them the randomness of this and they said they would look at it again.
Some mornings it comes on the when I leave and stays on and may be on after I get in after work (before I even move out of the parking spot), some days it's only in the morning and not on after work, some days it's on after work, some days it's not on at all but that has been rare that I don't see it at least once during the day, just seems odd and random so I suspect an issue.
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
My F-350 has developed a new problem. It wont start. It wont even turn over. All Electricity is on, glow plugs glow, gauges work, lights work, but when you turn the key to the start position noting happens. Some of the indicators go dark.
I even tried a jump thinking my batteries no longer handle the load. Same results. I suppose I can remove the batteries and take them in for testing. In fact, I'll probably do that now.
2002 F-350 Superduty, 7.3 Ltr, Turbocharged. 260000+ miles.
2004 f350 w 125000 miles.
I had diagnostic done at Autozone and no problems from check or OBD. The battery light has been coming on for a few minutes then going off at random intervals. Today I was towing trailer and quads, around 3500 lbs, to go riding and it was on most of the time running on interstate and highways.
Seems like the serpentine belt doesn't have as much tension as I would expect. Is there an easy way to change the serpentine? That looks to be a real pita.
2001 f350 7.3 diesel and I come up with the codes for upper and lower dual generator fault. I have only one alternator not the dual.. I checked the gauge and it is running at 14 consistently. But the service engine soon light keeps coming on...I clear them and they come right back... Alternator is only 2 years old and not a rmf..
View 1 Replies