Just did my first oil change on my 2015 Super Duty 6.2 engine. I got the Fram filter the book called for, a PH-2. There's goobs of room for the longer filter. Would that be the PH8A? The book is about to trying to figure the comparable long vs short filter. Why do they insist on those short filters when a full size will fit? My Dodge Ram Hemi was the same way.
View 14 RepliesActually a couple of questions. I've had one oil change in my F250 6.7. Getting close to the second one. So, my question is, what is the computer using to decide when to tell you that you should change the oil? And, if you changed to a synthetic oil, could you go longer between changes? And, if so, would the truck's sensors be able to tell the difference in the type of oil being used?
View 4 RepliesMy 2011 f250 has 92k miles, I want to change all 16 spark plugs.
Do the 6.2l plugs have problems breaking like the 3v engines did?
I think I'm going to pull the passenger fender liner to get to the lower plugs in the head.
How does the coil pigtail unclip? I looked at them briefly earlier and it looks like you pull the red tab back, then press down and pull on the pigtail but that did not work and I did not want to break anything.
I have erratic changing of directions of the air control. It'll be on ac it will then change to feet or defrost. then stay on that for a while and flip again. It'll then stay on that one( usually vents). I'm guessing the selector switch or the vacuum egr valve.
View 1 RepliesI have now found a chit load of LED fog bulbs in my search. I don't want to change out the entire light, just the bulbs. How do the bulbs effect the side vision. Almost hit a deer a couple of nights ago with my F350.....don't want that
View 8 RepliesI need to change the fuel filters on my 2014 F250 with a 6.7L. Are there any special tools required and any tips on how to get this done?
View 7 RepliesHere within the next couple weeks, i am wanting to do some routine maintenance. right now on my list is just an oil change along with the fuel filter.
View 6 RepliesCan I change the Fog Light Assemblies on a 2008 Super Duty without removing the bumper? They are made of plastic and one is broke on the top and the other keeps getting water in it.
View 1 RepliesJust moved into the 250 from years of 150's. Now have 98 miles and read that the tran would have noise but normal while breaking in.
whats normal, not used to this much Clunk while changing from P to D ect. More noise than used too I guess.
3.73 gears
2014 F250, 6.2 gas 2wd....
How to change the bulbs in my outside mirrors.
View 2 RepliesSo, recently acquired my grandpa's "old" 2000 F250 with the 5.4. I am a pretty mechanical guy, not a mechanic, but not dumb and change my own parts for a lot of stuff. Anyways, when I got the truck, I noticed it didn't like to get warm, or so the gauge said. It would go a little above cold, but you could tell, not a normal reading. I did a coolant flush because the system desperately needed it, changed the tstat, and a few days later, changed the Coolant Temperature sensor.
I pulled the old one out, it was covered in amazing crud from many years of being in there. Slapped the new one in, nothing. Doesn't register on the gauge at all, in fact the gauge acts like it is a dead gauge. I thought it might be the sensor, so I popped the hood again and found I had managed to break the plastic plug on the sensor. Figured that was probably the issue and went and got another. Same result. Checked the connection, it is in there snug. Didn't reset the PCM when I changed the sensor and some vehicles can be finnicky about that.
I have a ford f350 2000 7.3 powerstroke. I changed out the powrstwering hose because there was no powersteering. now my brake pedal is easy to push and don't have brakes. Reservoir stays full so I'm not leaking any.
View 1 RepliesWhat are the main differences between the F-350 and the F-450?
I see now that you can get the wide track front axle on the F-350 as well.
I just bought a used 2013 F-250 4x4 and it came with the snow plow pkg. heavy duty front springs. I love the truck, but won't be plowing with it, and I don't need the rough ride (and don't like the look of the front end higher than the rear)
How hard is it to swap out the front coil springs and replace them with the "regular" ones?
I just bought this Super Duty with a 5.4L engine. I want to do a fluid change on the transmission. From what I read, this transmission needs to be hot flushed in order to change out all the fluid. I have not called my dealer yet to see if they do hot flushes. If my local dealer does not have this machine, can I just drop the old fluid from the pan and be ok? I have not gotten under the truck yet to see if it has an external filter.
View 6 Repliestime to change the tranny fluid and filters on my 2010 F250. nothing in my owners manual about this.
All the parts look up places say I need 2 filters, the internal (FT-180) and an external (FT-145).
Problem is that I cannot seem to find the location of the external filter.
Doing some research, it looks like mid-08 the external was eliminated. So, do I have just the internal or do I have the 2?
Regarding the fluid. If I use the Maxlife dex/merc that says meets the LV spec, will that be ok to mix with whatever is in there now? (assuming LV, but I bought used with 145k on it, no idea if its been serviced before and if so, with what).
Going to check with dealer about the hot flush machine, but I really doubt they have one, and I'm kinda concerned about doing a flush at 150K not knowing the history of it.
Last night was changing front driver's side shock on my 2011 F250 PSD. Right front wheel still on ground and needed to turn wheel to right to better access shock mount. Started truck and turned the wheel all the way to the right and took the key out thinking the wheel would lock and I could change the shock easier. But the wheel didn't lock and actually spun itself almost a full turn after I took the key out...I'm assuming because the right wheel was still on the ground providing resistance, but I think the wheel lock may have broken.
Finished the shock and went to start, but nothing. Everything is clicking and buzzing like normal but wouldn't turn over. Checked all fuses that seemed pertinent but none were bad. Wasn't able to check any relays. Gave up and was going to have it towed.
Son and I had to straighten the wheel so I could roll in down the driveway and the dang thing started after the wheel was straight! Thought it was a fluke and parked it. This morning did the same thing so I cranked the wheel to the right and it started again. Now at work and thought I better check again and I can't get it to start for anything. The steering wheel lock seems to be busted and now I'm thinking it could be something in the steering column, but this is a little above my pay grade.
Need to get home tonight and was hoping my description would be enough to make a for sure diagnosis. Otherwise its getting towed to the shop and I'd rather fix it myself if i can.
So went back out and tried starting in neutral again, but this time fiddled with the shifter while turning the key...nothing again. Ran it up into park and tried it again and it started! Last night and this morning I didn't mess at all with the shifter, just manually turned the wheel with the engine off. This is the first time moving the shifter worked and I didn't turn the wheel at all this last time.
I am changing the plugs in my 98 e150 today and I was thinking it was a .54 gap and 13 ft/lbs to tighten them. That sound about right?
View 9 RepliesWas going to change my transmission fluid and filter today but when I got under the truck to see what tools I needed, I was not sure I could drop the pan enough to get it off.
I have a 2009 V10 4X4 and the exhaust pipe catalytic are running down each side right under where the transmission pan is. It looks like I can get to all the bolts, but because of the catalytic are right under the flange of the pan on each side, the pan will not be able to drop straight down. It looks like it may drop about 3 inches before it hits the catalytic.
Will that be enough to slide the pan forward or maybe tilt it to get it out? Has anyone dropped the pan on their 4X4 with the 5RW100? Just looking to have someone say I can get it out before I try it.
Any luck changing the external transmission fluid filter, without breaking it or its piping?
View 2 RepliesI'm in the process of changing oil seals on my dually front end. Do I need to worry about backlash settings? I see the gears are attached with solid brackets, which I assume, as just torque to spec and not worry about backlash. What is the torque spec for the four bolts holding the gears/yoke in place?
View 2 Replies