I want to remove the 4x4 stickers on my 2014 SD box. I think it looks cleaner without them. Are they difficult to remove or does the hair dryer trick and then some Goo-Gone do the trick without a big time effort? The last thing I want to do is make a mess of the paint finish.
View 13 RepliesHow do you remove the air bag on a 2014 F350 super duty. I have search every where. Nothing new on Google.
View 5 RepliesI've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 RepliesLooking to get rid of the step handle, I did this mod on mine and it was a direct fit...take off old liner and unbolt handle, then get a liner from a non-step tailgate and it is a direct fit:
View 7 RepliesOK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
I am wanting to take off the center console lid to recover it. The only way I see to remove just the lid from the truck is to hit the rod out that is in the hinge. I was hitting pretty hard with a punch and it wasn't moving. I don't really want to break it so I'm asking if there is a different way or if I just need to use more force?!
View 4 RepliesIs it necessary to remove say about one and one half cups of oil from the HPOP reservoir when changing oil? I say not needed.
View 3 RepliesI have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 RepliesI dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 Repliesdoes it take a special tool to remove pcv valve from 2005 e-450 v-10
View 1 RepliesI can't figure out how to get my front brake rotors off to replace them. I removed the caliper and thought the rotors should just come right off but they didn't? I then pulled the hub out and there was a retaining ring with a good size nut behind it , but you shouldn't have to remove the hubs to remove the brake rotors should you?
The stats of the truck are 04 f250 4wd w/manual hubs!
Just bought my first 04 F250 super duty Xl...4x4 Ext Cab...need to get this bench seat out and buckets and console in!!! I hear this is easy swap but never done before, or believe anything is easy.
View 1 RepliesHow to remove the overhead console on a 2012 F-250 ? I would like to tap into the wiring to power my radar detector.
View 7 RepliesI want to get the rear fender flares on my dually painted, they had a few scuffs when I bought it & I will soon have some spare time to get it sorted. We can't get the truck in the paint booth so taking them off seems like the ideal solution. I have had a quick look & I think it's just a case of removing the plastic liner (screws & clips) then it looks like there are some nuts up inside the steel fender, disconnect the wiring & they should come off!
View 2 RepliesI started to do my manifold and am 2 and 2. I got 2 out and two broke on top. So far I haven't been able to do anything w the bottom. I have basically seen 2 ways to get the studs out when they break. The first I'd to drill w an ez out and the 2nd is to weld a nut on. I'm not great w a drill and can't weld. I was wondering if using JB weld might be an option. I have never used the stuff but supposedly it's pretty strong. Is there any risk of welding the nut to the head?
View 12 RepliesI'm replacing the passenger side manual hub on my '04 F250. I did a brake job last year and I'm sure I cleaned/inspected/lubed the hubs. I can't seem to get this one out. I have the snap ring out and with a rubber mallet, I can get it wiggle just a little. I've loaded up around where the snap ring went with penetrating oil.
Am I missing something? It's just a snap ring and the hub should just pull out, right?
Have recently been getting a "TBC Fault" message and the Beep, as the message goes on and off(annoying) looked around think its the Controler itself,,If I move the slider, and Jiggle it,,the message Blinks on and off as I move the Slider,,,Looking for the method of removing it from the Cubby Hole,,,Gave it a tug,,,and wiggle did not move must have a Clip or Tab to release it.
View 8 RepliesI am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 RepliesI was told that I have to disconnect both batteries if I want to remove my seats by a car-stereo place. Is this true? They said it was because of the air bag sensors.
Gotta remove the center seat to get an amp out from under there and to do that, you have to remove or at least loosen both front seats.
Is there a way to do this without disconnecting both batteries?
Truck has been neglected for a while so this upgrade/repair I installed Powerstop brake rotor, caliper, bracket and pads. New Timkin wheel bearing, Moog U-Joints, and new inner/outer axle seals. Also replaced all the brake hoses and the remaining original rusty brake lines. About a month before I replaced the failed Auto/Manual vacuum operated locking hubs with Mile Marker units, which do not need the vacuum line, the drivers side was missing. and was letting water into the wheel bearing. So I decided to plug them and remove the vacuum lines from under the hood as well.
If there is interest I can get pictures of the vacuum lines, and what I changed under the hood. That was pretty self explanatory.
Could not find a google search for the thread size of the vacuum nipple in the knuckle. It is a 3/8"-24 fine thread.
[URL]
How do I remove the neutral safety switch? I bought a replacement and am having trouble removing it.
After shifting into neutral, I disconnected the connector, then unbolted the two screws. Now I can't get the little white ring that connects the lever coming from the transmission to the actual switch. I have tried prying it off with a screwdriver, spraying a little PB Blaster to lubricate it a little. Nothing will get it off it seems.
I'm leaving to go back up to school tomorrow afternoon, and I need to have this fixed before I leave.