Ford Super Duty (1999-2016) :: 2012 F350 - Hellwig Front Sway Bar Installation?
Oct 30, 2013
Installing the Hellwig 1 1/4 inch Front Sway Bar on their 11 and up F250 or F350 SRW Pickup?
My 2012 F350 Super Cab LWB XLT 6.7L seems to have quite a bit of sway in the front end. This is especially true moving slowly such as turning into service stations or other off angle turns. The truck only has the FORD OEM puny Rear Anti Sway Bar but the front seems to accentuate sway. The Truck has Rancho 9000XL Shocks, Timbren Enhanced Suspension System as well as Torklift Quick Release Stable Loads in the rear.
The Truck I have is not overloaded but it does carry an Eagle Cap 950 Camper pretty much full time. True the Campers now days are tall so some sway is expected. I just want to reduce the apparent front end sway and wonder if others have used the Hellwig Sway Bar in the front.
View 1 Replies
Advertisement
We just purchased a new 2012 F 350. Love it, however when shoping forgot about getting one with a step. Have found step and handle available (OEM) but need to know how hard/easy to install it on our current tailgate. I gather from another post the handle part is easy but what about the step itself?
View 2 Replies
I am installing a set on a '12 F350 for a customer. I already had to go buy an additional hardware in order to get the back bumper on correctly...and now I'm looking at the front bumper and I swear I don't have the parts I need to install it. It appears to be missing some brackets. There were NO instructions with them (apparently a chronic problem with Road Armor) and I can't possibly imagine it bolting to the flimsy brackets that hold the factory bumper (fairing would be a better word for it) in place.
View 6 Replies
I have a 2012 SD Reg cab 350XLT, I am installing the premium sound tweeters on the door pillar. Looking for the diagram for the big plug that connects all the door stuff to the truck body? I need to find the tweeter wires, or figure out another way to jump the gap from the door to the body.
View 1 Replies
Any good info on front brake replacement parts to get better braking out of these beasts? My pads are now needing replacement but I would like to get better performance than that of factory parts....
View 1 Replies
I have a question on the 2012 F-350 with 6.7. I have found after mid to long drives when I shut the truck down I can smell coolant when walking around the front of the engine. Seems more so from the driver side but i have yet to see any leaks or wet spots on the ground. I had the water pump and lower rad hose replaced last year under warranty and though it might have been residue but after a year and still smelling it it has to be something else. I only have 30,000km's left under warranty so if I need something replaced it should be soon
View 8 Replies
Installing a Pop N Lock on a 2016? What were the wire colors you tapped into?
View 3 Replies
This is my sway bar and drag link look like with the wheel turned all the way to the right. When I took these pictures, I had put the right tire on the curb too see what it was going too look like. However. Even with all wheels on level ground. It still is running very close. When the steering is straight, I have maybe 1" to 1.5" clearance between the 2. My truck does have a readylift 2.5" level kit on it. Running like this stock or leveled? Should I look around for longer sway bar links?
View 2 Replies
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 Replies
2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?
View 5 Replies
I have an isspro sensor that I need to install on my 4r100. I have it all installed except for the actual sending unit. My question is where is the best place to put it?
I've watched multiple YouTube videos and it seems a lot of people use the test port on the driver side above the linkage. I found out the hard way that it is a very poor choice of location. A lot of people say that the best way is to drop the pan drill a hole and weld in the bung? I was wondering would it be possible to put it on the "out" line on the transmission oil headed to the cooler? 01 f-350 7.3
View 4 Replies
I just installed a new positive cable set for the dual battery's and the starter checks out good.
View 5 Replies
I recently purchased a 2012 f350 power stroke. Love the truck but went out this morning and the air would only come out of the vents. I couldn't get anything out of the defrost or the floor vents? Truck is out of basic warranty so want to see if I can figure this out myself or if it needs to go in the shop.I've looked for a fuse but didn't see anything that ran an actuator door.
View 5 Replies
I have a 2012 Ford F350 I've been looking to install a compressor on. I've poked a hole in the gasket that runs wires through the firewall and cut the tips off of a couple of the accessory wires. Went to go get some more parts and now the truck won't start! The lights and radio turn on when the car is turned on but the starter doesn't even click when I try to start it. What should I look at?
View 7 Replies
How do I disable the day time running lights on 2012 f350?
View 4 Replies
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 Replies
I have a 2012 Ford F350 SRW 4x4 Diesel. Love the truck and has been great. I have 20" Tires and the ride on this truck is really rough. I know its now a Cadillac but to change tires or suspension components to get a smoother ride. I was thinking about going to 18" rims and getting a big all terrain tire. Maybe taking a leaf spring off in the rear. Going to air suspension. Different tires maybe. I dont need the load rating since i sold my fifth wheel.
View 13 Replies
I have a 2012 F-350 SRW with a 6.7 diesel. The other day I went to push the defrost switch and noticed it does not work. All the lights work in the switches, and the temp control works, but no matter what I push, defrost or floor, it stay in the vent only. Anything I can check??
View 1 Replies
What are the normal running temps for the tranny of a 2012 f350 6.7?
View 3 Replies
Found some threads on this but mostly for the 05-07 models. I am wondering if it is possible to install the upgraded message center (right above the steering column) into the dash of a 2012 F-350 XLT that has only the 2-line text message center?
View 1 Replies
While driving into town during a recent snowstorm, my truck started to misfire quite badly. The check engine light started to flash and then remained on as I went to the auto parts store. The code indicated cylinder two misfire. I don't a few things of dry gas in the tank and let it run for a few minutes which seem to solve the problem.
Since then, however,every time the engine gets even a little bit wet it starts to bark again. It usually lasts a few minutes then goes back to normal. Typically, I would have replace the plug wires. When I lifted the hood of my truck I realize I knew nothing about it.
View 2 Replies
