Ford Super Duty (1999-2016) :: 2012 F250 - Sticky Residue Along Button Of Doors And Around Hinges
Jul 23, 2017
I bought a 2012 F250 6.2L 4wd recently, truck came from Canada, Noticed a sticky residue along button of doors, around hinges, inside front and side edges of hood, some of the goo is in the A/C coil, doesn't have much odor, maybe oil, comes off with degreaser, doesn't look like it came from engine as that is clean, could this be something they spray on the roads up there? Doesn't seem to harm anything just messy if you rub up against it?
View 8 Replies
Advertisement
I posted a reply her a couple of weeks ago on how I fixed my '03 SD's squeaky doors. I went to AutoZone and bought 32 feet of 5/8 inch self-adhesive rubber (not foam) weatherstripping and mounted it around the outside edges of both doors, starting at the top. Presto - squeaks are gone, there are no more drafts and road noise is reduced a little. (I may remove the stripping I put on the side edges of the doors because I think the culprit is actually the rigid polyethylene bumper strip they've mounted on the upper door jam).
View 2 Replies
I have a "rattle/knock" that I think is coming from the doors on my 2000 F250 SD extended cab. The rattle is only there when the truck is going over bumps....especially closly spaced bumps. My buddy has the exact truck and it does not rattle.
View 14 Replies
1999 F250 extended cab back doors won't open. The passenger side stopped opening right after I purchased it a few months back (168K miles). I removed the door panels and reached my hand in feeling around. I know the latch releases are activated by cables but cannot figure out how they work. While feeling and pulling on the cables one became dislodged from its holder. The driver's side stopped opening yesterday . Do the cables stretch, break, or what? Or are the holders the issue? Is there an illustration that shows how the cables are run and connected?
View 14 Replies
What this could be? It blinks all the time was on the truck when I got it. Has a button in the bottom of it. This is on a 2009 super duty 250 and the 6.4 L if that matters.
View 3 Replies
I just bought a 2011 F250 Super Duty 6.2L and the manual A/C buttons were stuck on Max A/C and wouldn't change. I fiddled with every switch on the dash thinking it might be a stuck switch and eventually all the buttons started working. This truck has SYNC, which works fine, and I can't find anything else wrong with the truck.
When the buttons are lit, it blows good and cold, in A/C and Max A/C. The problem I'm having now is that they won't light up at all. Visual inspection shows nothing obvious under the hood, and it has a charge of freon. I drove and it id working just fine, but stuck on the Max setting. I'm thinking electrical gremlins, like stuck switch or a relay...
View 1 Replies
I have a 2012 F350 and the interior lights and cargo light do not turn on when I open my doors. The maps lights work if I manually turn them on. Why this happens and how to correct this issue?
View 2 Replies
06 6.0
Goes from max to min line on degaus bottle every couple months. No puking or white residue. Going to pull egr tonight and see if damp. Anything else to check besides obvious leaks at hoses/radiator/etc?
View 13 Replies
Trying to perform master reset on sync because, from the title, phone button inoperative, No Aux In, and attempting to connect the ipod, you get "connection error see dealer".
The Owner's manual indicates Fuse 40 protects Sync, GPS and Sirius, so I figure that is the one. When you pull 40 you still have gps and Sirius, so I figure Sync must still have power also. So, what fuse powers the sync module?
View 1 Replies
I have a 2005 f250 super duty turbo diesel 6.0 automatic. The problem I'm having is, when I engage the tow/haul button the transmission doesn't down shift unless I feather the pedal. Also the engine will overheat at times. I've replaced the thermostat, but that's all so far.
View 2 Replies
Just purchased my first ever Ford truck a few weeks ago, it's a 2012, and where the drivers right arm rested on the center console, near the cupholder, it's perpetually sticky. At first i thought it was just filthy, but after thoroughly cleaning it, it just stays sticky.
View 12 Replies
I read in a thread about how fog lights need the auto light sensor or something in the kit to be installed and flashed.
My truck is a 2012 f250 XLT that I bought left over from a podunk town IN illinois. It does not have fog lights but it Does have automatic head lamps. So Im very confused on what kit to order to add fog lights to my truck.
View 3 Replies
2012 F-250 6.2 gas 4X4 SC/SB: when I run WOT, or near that, from a slow speed, I hear a short "hiss" between the 1-2, 2-3, and i think 3-4 shifts. I can also feel that the engine eases up quite a bit during the shift, and it is kind of a slow, soft shift. It has about 2,000 miles on it. I bought it in March 2013 as a leftover (great price!). The door sticker says it was manufactured in 4/2012, so it sat on the lot for quite a while before i bought it. But i don't remember it doing this when it was newer (~500 miles).
With the lite weight of this configuration (it is an XL so it isn't even carrying around 4 speakers ha ha), and me rarely carrying a very heavy load (yet) or towing anything, I rarely have to step on it very much in normal driving... it hardly ever gets above 2,500 rpm unless I am just running it faster for fun.
The hiss and slow shift happen at any transmission temperature. Of course, it never has been above the left side of the "gear" pic on the temp gauge, where it always is after full warm-up. Well, I'm hoping it is just shifting soft like this because it has "learned" my lite-foot driving style (even when I'm in a hurry of course the engine rarely has to work very hard).
View 3 Replies
I've got a 2012 F250 XLT with AM/FM/CD/AUX radio, and the display is not working. The radio functions fine, as do all other electronics on the truck, but the display is dark. I've tried pulling Fuse #29 in the passenger kick panel, and it looked fine. Is my radio toast?
View 3 Replies
I have an 04 lariat f350 and after cleaning the steering wheel it is a bit sticky.... What the material is?? Or how to resolve the sticky issue??
View 8 Replies
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
View 6 Replies
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 Replies
I just purchased a 2012 F250 XLT with the 6.2. It has 38,000 miles on it. Yesterday I noticed, when coming to a stop, the idle will sometimes drop below 500. The engine will stumble a little, then the RPM will jump up to 1,000. Twice it has stalled on me. When it stalls, the engine will restart just fine. No codes in the computer or warning lights on the dash.
I will be bringing it back to carmax, as it is under their 30 day warranty still. Hopefully they will be able to figure out something. I am thinking either the TB needs to be cleaned, or there is an issue with the canister purge valve. I saw the TSB for the CPV but it doesn't cover my truck.
View 6 Replies
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
View 11 Replies
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 Replies
2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 Replies
