Ford Super Duty (1999-2016) :: 2012 F250 - Starter Spins / Spools Up Very High And Loud But Not Crank The Engine
Jul 20, 2017
Starting about 4 months ago, when starting my truck, the starter would miss; I would turn the key to start, then the starter spins and spools up very high and loud but not crank the engine. I have to turn the key off to make it stop and then try again. Usually the second or third time it will grab and turn the engine and start. It happens about once a week or once every 10 or 12 times I start my truck with all the other times being normal. Doesn't matter if it's a cold start or already warmed up. It's a 2012, 6.7L F250 with 52,000 miles. What is causing it and how it can be fixed.
View 1 Replies
Advertisement
My 2007 f250 power stroke 6.0. My A/C comp went out. After replacing it I was told that my fan clutch is bad and will cause the new ac to go out. My engine is not running hot. The fan still spins for a while after engine is turned off.
1) Could it have not been re installed correctly?
2) How do I know my Fan Clutch is bad?
3) How do I replace it myself?
View 6 Replies
I have a 2005 f-250 King Ranch 5.4 triton engine...my problem occurs when i turn the key to start the pickup....i get a clicking sound and then nothing....when i use a portable jump starter, it fires right up...on the other hand, when i try to jump from a running vehicle i only get a clicking sound from the starter...
not sure what i should be testing...also, when i bought the vehicle it had been sitting for several months...for my test drive, they used a commercial charger/starter to fire the truck...i drove it about 10 miles, stopped, turned off the motor and 10 minutes later it wouldn't start...when i contacted the owner, he drove to me and "reset" the kill switch under the fuse box in the cab and then jump started the truck...
I drove it 40 miles home and for 4 days had no starting issues...on day 5 forward, i have had to use the portable jump starter every time...my battery shows 13 amps resting and drops to 5 amps when i try to start without portable jump starter...when i start it with the portable jump starter, it only drops to 10 amps...
View 7 Replies
I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
View 12 Replies
Ok I reinstalled the new rotors and pads clips and warning tabs. The rotors match the old rotors size , thickness and hub clearance. 2 questions
Vehicle still on stands ....
After tightening everything up on the passenger wheel and the rotor seem to have a lot of play or movement... Normal or not ??
Now drivers side hub and lug nut spindle is not moving , possible another issue ....
Passenger side spins freely ....
if I did not have bad luck I would have no luck at all with this truck
View 8 Replies
I have a 1999 f350 7.3. Turn the key lights and fuel pump come on but the starter wont crank. I replaced the starter and checked all the fuses i could find. The only way i can get the truck to crank is by jumping the relay under the hood .
View 5 Replies
2015 F350 6.2, 4 door 8' bed FX4...... 17,200 miles.
This morning when outside to start it (nice sunny morning) and turned the key and all the dash lights went on and also went crazy. Said it had all kind of problems on the dash, Trac system, Over heating and so on. The starter did not crank over at all. Tried this about 8 times in 45 minutes, no worky. Call Ford, they towed it to the dealer. I last drove it 2 days ago. All stock, no programmer.
View 12 Replies
Got 01 F350, 7.3
Started having issues with starter bogging down my batteries. Slow crank, it would catch anyway and runs great. I have spare used starter in the garage, threw that on and it cranks fast, but occasionally just free spins half way thru the cranking.
My question is, can I make one good starter from these two? Monday AM buyer is coming to get my truck, and I don't want to have to buy brand new starter if I can avoid it, but I want him to have reliable used starter.
What causes free spinning (not flex plate related), and what causes power drag and slow crank? I was thinking throw solenoid from fast starter onto slow one, since slow one doesn't spin out but it bogs down my voltage?
View 1 Replies
I have a 1999 f350 7.3. Turn the key lights and fuel pump come on but the starter wont crank. I replaced the starter and checked all the fuses i could find. The only way I can get the truck to crank is by jumping the relay under the hood.
View 9 Replies
I have an 02 F250 6.8 with 51,000 miles on it. I recently replaced the battery about a week ago, and only actually drove it yesterday for the first time since replacing the battery. I drove it about 25 miles, parked, and when I went to restart, it wouldn't. The starter doesn't crank, so I mean its not a cranking issue as in cranking, and not starting. It only clicks at the relay when turning the key. It acts like when you try to use a wrong chip coded key.
All of the dash lights came on, and I can hear the relay clicking, but that's it. I swapped the relays around, and no luck. If I let it sit a while, about an hour, it will fire right up. The battery cables are tight and free of corrosion. I am curious, since I just put in a new battery, could this be the culprit? Why will it start fine cold, but not hot? I have NEVER had an issue with this truck until now.
View 14 Replies
I drive a 2000 F250 5.4L. Currently has about 168,000 miles on it. I changed the oil the other day and cleaned the air filter. I used what I usually use on the oil change which has never been a problem. But this is first time to clean the K&N filter. A day or so later my engine is making a loud air rushing noise. Under throttle the engine compartment sounds like a wind tunnel. At 3500ish rpms it makes a harsh whistle noise. The air rushing noise doesn't go away once its warmed up or after the engine has been cool. Noise didn't go away with the filter being taken off either.
Could all of this be caused by cleaning and not using k&n air filter oil (but rather WD40 upon Dad's suggestion)? Or is there something else going on?
View 8 Replies
Ok so I bought this 2012 f250 and I had a couple questions.
1. I checked the Frame for rust n it was fine. I didn't look at the other parts until I got it home. It does have some light to moderate rusting on other areas under the engine compartment. Ex axle, drive shaft, some of the steering components. Exhaust Manifold is pretty rusty though. What can I do about that?
2. I noticed a little bit of oil, not dripping, on the underside of the front of the engine. I do have an extended warranty so i hope it will cover that. It's pretty extensive of a warranty. I took some pics of the area where there is oil. What could it be?
Most of the oil is focused around there ...
Top down view ...
View 3 Replies
2002 F450 7.3 Turbo
Ok first problem : Starter Motor fuse kept blowing and I spent weeks trying to figure it out. No luck. so wired up a push button just to get the truck started, its a work truck so it was needed asap.
2nd problem : he truck stopped starting completely. Wont start in Park or neutral and after a NEW STARTER (because I thought the solenoid on the starter was bad I replaced it) Everything work correctly for one start with the key. After the second time trying to start it blew the starter fuse again. So I tried the straight wiring to starter. still nothing. I was wondering if there are any shims or anything at the transmission housing to correctly position the starter. I am thinking that maybe the gear is stuck or gets stuck sometimes. when I straight wire the starter it does nothing but the wire gets hot so I know its pulling.
View 3 Replies
To make a long story short, after replacing the timing chains, guides, and tensioners, the right side cylinder head began running very loud. Think of the usual chatter associated with these engines and multiply it. It was constant, from start up to shut down, and it increased with rpm. Thought at first it may be caused by debris in the oil clogging the lifter(s). After changing the oil multiple times along with different additives and driving roughly 600 miles, the noise persisted. Taking a look down the oil filler tube with a flashlight and with the engine running, the head looked dry. Safe to say at this point I was starving the head of oil.
Removed the valve cover. Removed the rearmost camshaft cap. Sure enough, the oil passage was completely blocked. Inspected everything and there was signs of running dry (minor discoloration, dried oil spots... but no real damage and no play anywhere. Put it all back together and the truck runs quieter than the day a bought it.
Here's the camshaft cap:
This is exactly what it looked like after removal. The material blocking the passage is hard and bridle like plastic.
View 4 Replies
Just bought a used 15 F-250 with 57,000 miles, yesterday tried to start it and nothing happened. Checked the starter fuse and it was blown, replaced it and it immediately blew when i tried to start the truck. Pulled the starter and had it tested and it was good, replaced the relay and still blowing fuses. I have got it to start a couple of times but as soon as you kill the engine and try to restart it blows the fuse. What was the fix? Truck had no problems trying to start before this problem started.....
View 7 Replies
I have a 5.4L 2001 F250. I recently replaced the starter and this morning when I turned the key it just started clicking. I had this issue a couple weeks ago and swapped the battery from another truck and it started fine for a while. But after this morning the relays are still chattering even when the key isn't in. I believe it's still the battery ....
View 10 Replies
I have a 02 F250 Super Duty XLT with a triton V8 with a automatic transmission . and when I shift into reverse after driving for a while the starter engages . It does not happen all the time . If i start up the truck and shift through or into reverse it doesn't happen . the only time it happens is when i've been driving for awhile and want to back up or park it will only do it once or twice after each drive so trying to get it to happen while in the shop is almost impossible . could this be caused by the transmission range sensor . I just had the code P0705 (transmission range sensor , A circuit input ) come on but the problem has been happening for a few weeks before that code came up .
View 6 Replies
I have a 2010 F250 V10 4x4. about every 3-4 times when you start the truck....it seems as though the starter "sticks". If I catch it and shut it off and then turn the key right back it fires up and does not stick. Its as if the gear is staying kicked out into the flywheel. Are we thinking the starter itself? I'm thinking starter...but looking for input before I crawl under it.
View 1 Replies
Truck would have a miss that went away when warmed up past 180. Ficm voltage was low so I got a new one from diesel tech ron. After I installed it The truck would crank for maybe 5-6 turns then lock up and kick the starter out. The starter broke away from the motor from the kickback. I got a new starter in and set up my scangauge 2. In the few turns of the motor i can do before it kicks out, ficm is at 48.5 koeo and cranking, ipr at 14.4, and the icp shoots up to 1100. The ficm sync wont come on and I m stumped what to do next. Dont want to start throwing new sensors at it. 2004 f250 6.0 ...
View 1 Replies
I have a 2008 f 250 super duty gas v10 i have never had problems with it start always starts right up and strong. After coming out of the story today I tried the remote start and it tried to turn for a couple seconds and stopped. I replaced the battery and starter and still nothing. i hear the relay when trying to start with both keys or remote start but nothing from the starter all lights are working .
View 1 Replies
2001, F250, Lariat, Super Duty, 7.3 engine with towing package.
It ran seemingly perfect when I parked it and it sat for maybe 10 days to 2 weeks and wouldn't crank. Battery is fine and fully charged. Glow plug heaters work OK. Engine spins really fast, almost like it had no compression. (Not sure though) Temperature in the 30's -50's. I did some research on line and decided to change the Cam Positioning Sensor (CPS). Didn't work, still won't crank. I originally tried my Cheap Harbor Freight OBDII . (Don't waste your money, IMO). What should I troubleshoot next/ or try.
View 5 Replies
