A buddy's 2012 f250 message center is not working at all. He replaced the fuse and it's still not working. The gauges work but not the high tech information center. He isn't sure if it's out of warranty because he can't see the miles. I'm not sure that's it's anywhere related but his back up sensors do not work either.
View 3 RepliesFound some threads on this but mostly for the 05-07 models. I am wondering if it is possible to install the upgraded message center (right above the steering column) into the dash of a 2012 F-350 XLT that has only the 2-line text message center?
View 1 RepliesMy 2012 F-250 gas just started showing this message that a coolant change is required. I am just over 59k miles. Is this a timed message all F-250's get, or is it an indications something is wrong? The truck does not run hot, it keeps perfect temperature even when I am towing my 13klbs boat.
View 3 Replies2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 RepliesI have a 2012 F250 and am having a problem where the interior lights wont come on with the dash switch or when the doors are opened. I have confirmed that it is not a bad fuse, also the lights will come on when the switch on the individual lights is manually pushed, but not automatically like they are supposed to. I dont see it being a door switch issue because the door chime comes on and the stereo goes off when the doors are opened after turning the ignition switch off. I've read that the dealerships will switch out the BCM. I thought maybe the dimmer switch next to the headlight switch but there is no power to it whatsoever, which also I can't dim the instrument panel lights. What did you do to resolve?
View 1 RepliesSo on my way to work this morning taking off from a light on a smooth blacktop my message center lit up with "tire pressure sensor fault". is there any way to tell which sensor it is without a scan tool?
View 11 RepliesJust started having this issues on my 2012 F250 6.7 with 71K. Turn the key and no problems. Once I start my truck service advance track pops up, along with the e-brake light and some other lights before all shutting off. I then loose all functions in my instrument cluster, window controls, AC/heat controls. The truck still runs and drives with no problems I just have no dash functions. My blinkers and headlights still work (with no cluster indicating). Fog lights do not work. Turn the truck on and off and the problem repeats itself.
I did get stuck in a massive rain storm with some big puddles last night. Went to dinner and started having the problems on the way home. The functions were temperamental last night but seem to be worse today.
OK....my gas cap (5.4 gasser) wasn't put on properly at the gas station. A couple of blocks later, the "Check Gas Cap" notice came on. I stopped a few blocks later, and installed the cap properly. The notice STILL came on. After messing with the cap 4 more times, I gave up, but the notice is still on. Do I need to have it "erased" like a code, or is there a problem with the cap? Everything LOOKS fine...
View 2 RepliesJust got a 2008 F-250, truck has the center console jump seat and the console lid is missing. Can you just buy a new lid or do you have to buy the whole thing? Cost? Places to buy?
View 4 RepliesI'm having trouble resetting my oil life meter in my 16 F250. I think I'm doing exactly what the manual says but nothing is happening. I turn the ignition on and wait a second for the ford start up graphics to finish and then press the gas and brake at the same time as far as they will go. The manual says after 3 seconds I'll see a message saying the reset is in progress but I don't get any message on the screen. Am I doing something wrong?
View 5 RepliesI got a 2011 250 SD 6.2, I have what feels like a catch in the steering, on center, when you turn the wheel feels like it just gives and stay's there, either way you turn, Checked front end, ball joints tie rods etc., the hubs are unlocked, feels like when the u-joint on the steering shaft goes bad and you get that bind. But this truck doesn't have them anymore, just a rag joint at the box. It only binds at center, and wont return, took steering stabilizer off and road tested same thing, air in tires good all the way around, has about 58,000 miles on it.
View 6 Replies1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 RepliesFor those of you struggling like I was a few minutes ago... Here is a procedure that worked for me.
1. Key ON.
2. Select OK to get rid of OIL CHANGE REQUIRED message.
3. Scroll down to SETTINGS and push OK.
4. Scroll down to VEHICLE and push OK.
5. Scroll down to OIL LIFE RESET and push OK.
6. Scroll to any % other than what you want and push OK.
7. Scroll to what % you want and push OK.
8. Key OFF.
I have (2) 2014 f250's both have given the trailer disconnected message randomly from the day they were new. Dealer says everything is with in specification. I just live with it now but something must be wrong with the design. Only does it when no trailer is connected an might be worse when it rains. Might have to hit the ok button every 10 minutes so on bad days.
View 14 RepliesJust bought this '08 F250 CCSB 4X4 5.4 Problem is the steering seems heavy, it tends to wander at higher speeds and won't return to center after a turn. I've searched on here and found a few possibilities (axle u joints, ball joints, steering gear, etc). I have an appointment with the dealer on Friday to fix it under warranty but he is convinced it's the u joints in the steering shaft seizing. When my F150 steering shaft began to seize, it would be hard to turn then break free then be hard then break free and this is not what is happening on the SD. I haven't had a chance to check the front end myself but not sure how you would check the axle u joints if there was no play in them. How would you check to see if they were seizing up.
View 3 RepliesEvery time I put the truck in reverse, I get a "Check Rear Park Aid" message on my display.
I tried wiping all of the sensors clean, and I checked the electrical connections and all seem to be fine.
I have a 2013 F250 and to day the TPMS light came on with a low tire warning message. A little back history, I put new tires on the truck when I bought it and they currently have 9200 miles on them. I didn't like having the tires at the 80psi the tire shop set them at so I lowered them to 62psi right away and haven't had any issues with the low pressure warning going off. Today I was backing into a parking spot and the warning light came on with a low tire message. I checked all the tires and they were right where they should be, but when I got home I added another 5psi to see what would happen and the light never went off after taking it on a 10 mile drive.
My question is, do I have a wheel sensor issue or is something messed up in the computer? I know the door sticker says 75psi front/80rear, but I've been running the tires at 62psi for 9200 miles without trouble so I can't think that the pressure is the culprit. Also, does the spare tire have a sensor in it? In the manual in one paragraph it seemed like it does, but in the next it said that the spare doesn't have one so the light will stay on to remind you to change the spare out.
I've got an intermittent Trailer Wiring Error message that started appearing with a trailer connected on my '11 F250.
Brakes and lights work OK on the trailer, I thought I had read on the board here that there was a TSB for this, but I cannot find it.
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesI found water under carpet next to door. Appears to be coming from area above center of vehicle. Only occurs during rain etc. Not from A/C or heater housing.
View 14 RepliesMy 08, when I connect my 7-pin trailer up, bouncing down the road that message and tone CONSTANTLY going off....drives me nuts! I have went thru the wire harness 2x now, cleaned all the contacts, etc. Any other thing short of a 12 gauge? When it does pop on, the controller starts flashing...I've reached down a few times and manually hit the brakes and it still hits em so whatever it is, I feel its very minor or whatever....just don't know where to go now! All contacts have been cleaned good as well.
View 8 Replies