Ford Super Duty (1999-2016) :: 2012 F250 - Long Pedal Travel When Applying The Brakes
Dec 1, 2011
I took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
View 14 Replies
Advertisement
2004 F250, I am getting this howling noise when applying the brakes. It sounds like it is from the left front and is more prevalent when applying the brakes down an incline (off ramp, etc) I pulled the wheels off and the pads were probably 50-60% worn. I bought some new pads and installed them and I still get the same noise. I didn't buy the cheap pads, nor the most expensive either. Either way, I can't figure it out. Would I need new rotors? I would think I would have some vibration if the rotors were warped. My other thought was the caliper, but when I replaced the pads it compressed fine and I lubed the slide rails. Not sure what to do at this point. The truck has 94,000 miles on it, FX4, Lariat, Crew Cab, and it has the 5.4L in it.
View 2 Replies
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
My 99 f250 ran hot while towing my travel trailer when the fan clutch gave up. ever since iv been noticing coolant loss and pressure in the day tank.ive changed the water pump,radiator. day tank and cap plus the thermostat.
View 9 Replies
On the surface, the F-250/350 seems to have great brakes: big rotors, vented front and rear, and dual-piston calipers front and rear. But, I have two problems:
One is the annoying 'grunt' the brakes make every time you change from Park to Drive, or Park to Reverse, or Drive to Reverse. Its as if under normal brake pressure, the brakes cannot hold the truck from moving against the torque convertor engaging. It's not just my truck, I've heard older SD's with the 5.4L or diesel do this too. If you push the pedal really hard, it won't grunt.
The second problem I think is the root of the first: mushy brakes. Maybe I'm just used to driving european cars with firm brakes, but every time I apply my truck's brakes, it feels like I need to bleed the system! The truck does slow pretty well, and I realize it's heavy, but how can the pedal feel be improved? Maybe replacing the rubber sections with braided stainless?
Lastly, the truck has a 'hill-hold' feature which is retarded in an automatic transmission. My problem with it, is that sometimes it sticks on...engage drive, the truck won't move...a second later its like something gets unstuck and the truck kind of lurches forward.
View 12 Replies
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
I'm not exactly sure what's going on but it feels like I'm missing some brakes - the pedal is extremely spongy, I have to push it nearly to the floor. And when they do engage, it isn't with the same vigor as they did before.
It's strange, it just sort of happened - I drove to a friend's house, everything was fine. But when I left all of a sudden, there's this problem.
It's not like the pads have come apart and destroyed a caliper - I had that happen to me a few years ago and I definitely felt it happen, plus once it did I lost almost all braking ability as the lines would just leak fluid.
View 2 Replies
I have a 1999 f250 that runs and drives great but the only issue I have is when I baby the gas pedal it stalls a little and when I give it more gas it's fine or if. I'm going 50mph then let off gas and then baby the pedal it's stalls a little.
View 6 Replies
I have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems I was having the the speedometer and the transmission not shifting correctly. Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles?
Had to push the truck hard to get it back to my house, a mile or so. If I let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on. It was not on before but i am pretty sure the ABS is disabled on the truck. The wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
View 5 Replies
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
View 2 Replies
The other day I got in my truck and started down the driveway when I realized I had no brakes, I slowly backed up and parked it. I haven't driven the truck for approx. 2 weeks and it seemed fine then. The master cylinder is full, there are no signs of leakage from wheel cylinders or lines. Today I unscrewed the left front zert and no fluid came out. My pedal goes all the way to the floor.... Whats going on, and if its a easy fix?
View 14 Replies
I don't know whats up with my new truck, its a 04 f250 scsb, 4x4, 5.4l with 61k orig miles on it. Truck will stop on a dime, has NO pedal sinking, but it takes about 3/4 of the pedals travel to apply pressure to the pads and have the truck stop, sometimes if I push the pedal down then let up and push it again the pedal wont travel as far, I just flushed the system today, no air in the lines, is there a bleeder on the abs? truck has 4 wheel abs...
View 14 Replies
I have a 99 f250 sd truck that came as a auto and I am changing it to manual. I bought a slave cylinder unit setup and got it put in and as I was installing rod from pedal to slave I must of broke plastic fingers that hold rod. So is them fingers replaceable or must I buy another unit? with no foot on pedal it sticks up close to bottom of dash now. I tried pushing clutch all the way to floor and still rises too high. What can I do????
View 1 Replies
I have a 2002 f250 7.3 with a dead pedal and gauges. This has happened to me once before checked fuse 45 and it was blown. I didn't know that the po used a 30 amp fuse when it should have had a 15 amp. I replaced it with a 30 not knowing. Well coming home the other night it happened again gauges dead and pedal. Checked fuses all were good. Found this site and read about the cause in the shifter. Took that apart and fixed the wire that was broken in half. My question is what else is fried now from having a 30 amp fuse in while it was shorting out since I have no gauges and gas pedal.
2002 f250 banks six gun
banks 4 inch exhaust
View 2 Replies
So a few week back I noticed my brakes were getting soft. Soft meaning that when braking for any distance, I would hear a kind of "pressure release, squeaking" sound coming from the pedal, and the pedal would sometimes go to the floor and the ABS would kick in. Let me tell ya, its a pretty crappy feeling when your brakes aren't doing what their supposed to! So, I replaced the pads all the way around, replaced the master cylinder (bench primed). I took it out for a drive, and it did the same thing. So thinking maybe the fluid is bad, I flushed new fluid through the lines. Took it for a drive, and it felt good right away, the pedal firmed up a bit, and then it did did it again.
Just so I give as much info as possible, the rotors are looking pretty rough and going to be replaced soon.
So, my question[s] are; What is the next step in identifying the problem? Is there a chance the new master cylinder is bad? Could worn rotors cause the caliper to max out and not apply enough pressure? Even though the calipers seemed fine while replacing the pads, could one or more be bad? If so, how do I know?
View 14 Replies
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 Replies
I believe my brakes have a problem.
Lately, I can stomp on my brakes @ 50 mph and they won't trigger the abs or come close to skidding the tires. The peddle goes to the floor if I push hard enough and the truck doesn't seem to stop fast like it used to.
I'm wondering if there is an issue I should be focusing on, like swelling brake lines or some issue you may know of. I'll try bleeding the brakes this coming weekend, but i think its going to be a bad brake line or something.
View 8 Replies
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 Replies
I have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 Replies
I have a 2000 F-250 Diesel that has started acting strangely. It starts and runs well, but every once in a while the peddle just stops working. Might be a second or so and then the RPM will go up. Or you may be running down the road and all of the sudden it just stops acting like it is getting enough fuel. Same thing it might last a second or so. Sometimes it might happen 4-5 times in a row over a few minutes and might not happen again for a day. Truck does not stall when this happens. It just does not go like it should.
View 1 Replies
