I noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.
View 12 RepliesI have my front axles out to replace the U-Joints but they are rusted in there. Even the C-Clip is fused/rusted in place. I use my flat wheel grinder and ground out the C-Clips but the U-Joint caps wont budge. Been soaking in penetrating oil too. Any way other than drilling them out?
View 1 RepliesI am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesIf front wheel bearings can be greased through the abs wire hole on a f250 4X4, will that work on a sealed bearing on a gm product? I have done my f250 but I also have a 2004 suburban.
View 2 Replies2005 Ford 350. I want to change the ball joints on the front axel and I cant remove the axle out of dif. to remove the ball joint housing. I have been prying and pulling and it just moves out a 1/4 inch or so .They tell me there is no ring to remove in dif before you can pull it out but why this trouble?
View 4 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesI own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesI have a 2001 f250 7.3 4x4 today I locked the hubs, put it in 4 low and got threw some mud to go hunting fine. got back out of the woods and took it out of 4x4 unlocked hubs and went in reverse 30 yards.. Now when i drive it makes a weird sound like a rubbing sound near the front axle. What this is?
View 5 RepliesMy 2013 f-250 with 6500mi. has peeling paint on the front differential and the axle.. I sprayed it with some fluid film for now.
View 14 RepliesI broke 2 snap ring plier on this thing, what is the make and model of snap ring pliers used to remove the snap ring off axle in hub ? I have some others but too beefy won't move in there. They need to be long but strong. I've heard Snap On Item: SRPC9000A works but I don't know of any Snap On guys around here and I need to get this thing done.
View 10 RepliesI have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 RepliesI bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 RepliesAfter 240,000 miles I had to get the ball joints on my 02 f250 2 wheel drive replaced and the alignment set. I notice that the steering is really tight. In fact that it will not attempt to return to center on the highway. The guy that did the work has 30 years experience doing this sort of thing and he says I just need to drive it and it will loosen up. Interested in hearing from others that have replaced ball joints; Is this normal? How long do they take to loosen up?
View 7 RepliesI have a 2003 f250 superduty v-10 -- 4x4 -- when turning with 4wheel drive disengaged I have consistent thumping sound coming from front end -- more so when turning to left but still prevalent on right turns -- I put new hubs in due to the grinding noise when driving slow to mid speeds -- like axles not totally disengaging and grinding on teeth. but this is a secondary noise -- replaced left front axle with dorman unit -- tried to replace u joints on oe axle but rusted so badly couldn't get c clips to separate from ujoints --
this one is kicking my butt and making me look like a novice -- don't think it is ball joints or anything suspension related but I could be wrong -- sounds like thump thump thump as turning in slightly tight circle or going around corner in the parking lot.
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
Ok so I bought this 2012 f250 and I had a couple questions.
1. I checked the Frame for rust n it was fine. I didn't look at the other parts until I got it home. It does have some light to moderate rusting on other areas under the engine compartment. Ex axle, drive shaft, some of the steering components. Exhaust Manifold is pretty rusty though. What can I do about that?
2. I noticed a little bit of oil, not dripping, on the underside of the front of the engine. I do have an extended warranty so i hope it will cover that. It's pretty extensive of a warranty. I took some pics of the area where there is oil. What could it be?
Most of the oil is focused around there ...
Top down view ...
I need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 RepliesI have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 RepliesLove my '11 f250 SD 4WD CC SB. 6.2 with 3.73 e-locker. I've got 5 Star tunes in it, and the truck is a joy to drive empty, and tows my current 7k camper fine, though on steep inclines I wish I had the 4:30 gears.
Well, we just bought a bigger trailer, dry weight is an addtl 2400+ at 9400, so I'll need to do something.
I don't want a different truck, don't want (another trouble-prone) diesel. I think with 4:30s and the tune, I should be fine towing that trailer (with gear and passengers, probably 11-11.5k loaded). Not doing mountains here, just Michigan hills.
What's the best way to "do" a gear swap? I know if I buy a set of gears and a shop screws Em up, it's gonna whine/hum and still cost 2k to do (truck is 4wd)
I'm up in the boonies and finding a shop to swap the gears will be a problem. Getting Em done right will be even MORE trouble.
Can I just find 4:30 axles ans have them swapped (anything in t-case or sensors need to be touched?). I don't care if I lose the e-locker, I never use it.
Finally finishing up my 2001 F250SD 4X4 project. Decided to pull down the front axle to replace the dust seals. I've got everything apart including the large knuckle seals. Tried to pull the passenger side axle out but it only moves about an inch to an inch and a half before it stops. Took off the differential cover to look for damage or something obvious but I don't see anything wrong. The axle is moving within the splines of the spider gear but that's it. Stumped and sitting on jacks!
View 14 RepliesJust got done rotating my tires on my 16 F250 ccsb 4x4 and I used jack stands on my rear axle while I used the jack on the front axle. When I brought the truck down off the jack stands (first time using jack stands on this truck) I saw that they left little marks/divits on the rear axle. I had them between the wheel and the shock support and I can feel with my finger where the jack stand was supporting the truck. It doesn't seem anything major but I can surely point out to you exactly where the axle and the jack stand met. I'm sure this is a non issue but just wanted to check in here to make sure...
No trailer attached (of course!) And nothing in the bed with a full tank of gas...so basically just the weight of the truck...