I have a stock 2012 F250 6.7 Diesel. I was looking at getting new 18 or 20 inch rims for it and was wondering what the largest tire I could fit on those without rubbing on the truck would be. I know there are lots of topics on this but I could not find anything that applied to me. Most topics were on stock wheels.
View 1 RepliesI have a 2007 King Ranch F250 that had 18" rims on it. I just put a new set of 2008 KR 20" tires & rims on my truck and now the ABS light is on. Does increasing the tire/rim size mess with the ABS? If so how can I remedy this?
View 1 RepliesI have a 1992 Ford F-250 custom 2WD. My stepfather in law gave me rims from a 02 Ford F-250 for my truck. But I know the lug pattern is different so I will be wanting to put some adapter/spacers for those rims. But I need to know the offset of the rims I have now to make sure I'll still have a turning clearance if I was to get the adapters/spacers.
View 4 RepliesI'm planning on doing a 2" level. Will I need a drop pitman arm, or can I stick with the stock pitman arm? Will I need anything else? I plan on doing the level when I replace my coil springs and shocks. (I have another thread on that). I'm driving a 2000 F250 V10 2WD CC SB (twin I-beam front axle) if that info is pertinent to this question.
View 2 Replieswant to raise the front of my 99 f250 super duty. I only found rough country for my options. I am looking for a 2-3" lift. Will the 3" lift spindles work fine? What else am i going to need? Shocks?
[URL].....
I put some bfg at's on my '16 f250 6.2 today, 285/70r17 from 245/75r17. Has went to a larger tire and had funny downshifts? I had two hard down shifts on the way home from tire shop that I have never had before. I'm hoping this will go away once the computer relearns. Should I disconnect the battery or anything or just drive it and let it learn? I'm a little disappointed, the tires still look tiny, and checking clearances at liners and radius arms, I could have cleared a lot more tire easily. They sure looked bigger on dads '04. These will do me for a year or so until I can upgrade wheels, tires and suspension.
Before
After
We have a lot of snow and a lot of ice up here at the moment and my 2003 ford F-250 SC Fx4 isn't performing so well. The truck is stock other than a pair of 285/16R BFG A/T's
I have been noticing that my rear tires will spin while trying to go up hill on some ice or snow covered areas and my front tires just sit still while in 4x4 or 4x4 low. In the case I just described I remain stuck in place until the rear tires can get a grip then I continue up hill. I don't understand why my front tires are not spinning as well, to me this seems just like 2 wheel drive not 4x4. I have been using ESOF most of the time. I have mentioned in other threads that I do plan on upgrading to warn premium hubs, but I am wondering if its that my truck isnt actually shifting into 4x4 or if there is a reason why even in 4x4 my rear tires would spin while my front tires do not?
I am confused because when I shift on the fly while driving I can feel the 4x4 kick in because it just feels different than driving with 2 wheel drive, but then something like I described will happen and I start second guessing myself. What might be happening? It's not that I am opposed to switching to the warn premium hubs, but is that actually going to fix this issue or is my truck acting normally??
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 RepliesI got a f250 4x4 1999 super duty , I have 20" 10'rims , can I run a 35" 12.5 x 20" tires without rubbing
View 1 Replies just got 20" rims 295/65/20 Nittos. Is my odometer accurate and speedometer?
Not that it matters but its a 99 F350 CC LB 3.73 axle ratio
I read in a thread about how fog lights need the auto light sensor or something in the kit to be installed and flashed.
My truck is a 2012 f250 XLT that I bought left over from a podunk town IN illinois. It does not have fog lights but it Does have automatic head lamps. So Im very confused on what kit to order to add fog lights to my truck.
2012 F-250 6.2 gas 4X4 SC/SB: when I run WOT, or near that, from a slow speed, I hear a short "hiss" between the 1-2, 2-3, and i think 3-4 shifts. I can also feel that the engine eases up quite a bit during the shift, and it is kind of a slow, soft shift. It has about 2,000 miles on it. I bought it in March 2013 as a leftover (great price!). The door sticker says it was manufactured in 4/2012, so it sat on the lot for quite a while before i bought it. But i don't remember it doing this when it was newer (~500 miles).
With the lite weight of this configuration (it is an XL so it isn't even carrying around 4 speakers ha ha), and me rarely carrying a very heavy load (yet) or towing anything, I rarely have to step on it very much in normal driving... it hardly ever gets above 2,500 rpm unless I am just running it faster for fun.
The hiss and slow shift happen at any transmission temperature. Of course, it never has been above the left side of the "gear" pic on the temp gauge, where it always is after full warm-up. Well, I'm hoping it is just shifting soft like this because it has "learned" my lite-foot driving style (even when I'm in a hurry of course the engine rarely has to work very hard).
I've got a 2012 F250 XLT with AM/FM/CD/AUX radio, and the display is not working. The radio functions fine, as do all other electronics on the truck, but the display is dark. I've tried pulling Fuse #29 in the passenger kick panel, and it looked fine. Is my radio toast?
View 3 RepliesIm just about due for some new tires before this next michigan winter. I have 18" rims with the stock 275/70s. What size can i go up to with out any trouble?
Also. I have michellin ltx/2 now. Mostly highway miles with some muddy job sites and also to my 8000lb camper 6 times a year.
Have a 2012 F250 4x4. Have read many posts about different lifts etc. I don't want to go real big but I would like to go to a larger tire than the stock Michelins.
On a F250, done a 2 inch front leveling kit and switched out the rear blocks to F350 blocks. Assuming I wanted to put new shocks on with this change, what level kit and what adjustable track bar (from what i've read this is pretty much required).
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 RepliesI just purchased a 2012 F250 XLT with the 6.2. It has 38,000 miles on it. Yesterday I noticed, when coming to a stop, the idle will sometimes drop below 500. The engine will stumble a little, then the RPM will jump up to 1,000. Twice it has stalled on me. When it stalls, the engine will restart just fine. No codes in the computer or warning lights on the dash.
I will be bringing it back to carmax, as it is under their 30 day warranty still. Hopefully they will be able to figure out something. I am thinking either the TB needs to be cleaned, or there is an issue with the canister purge valve. I saw the TSB for the CPV but it doesn't cover my truck.
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 Replies2012 f250, fog lights stopped working and tried fixing yesterday. I'm getting 12.8v at the plug but as soon as you plug the light in it goes to 0. Ran a new ground from frame and the hot from plug and still nothing. High beams off, truck running and switch pulled out. Bulb is fine, hooked it straight to battery and it comes on. I though it was a faulty ground but by running a separate ground and still nothing. I'm at a lose.
View 2 Replies