Ford Super Duty (1999-2016) :: 2012 F250 6.2L - Misfiring On Multiple Cylinders
Jun 30, 2017
I have a 2012 F250, 6.2L, Crew Cab, FX4 with a little over 77,000 miles on it. I bought it used from a Ford dealership last summer. Prior to now, I've only had one issue with it and that was squirrel/rodent induced. Something chewed through the wiring harness right before the connection to the #7 cylinder. There was enough left over wire to solder it back together and put heat shrink around each wire.
It ran fine up until last weekend. The wife and I went to a store, she was driving and parked like a total jerk right in the front area of the parking lot. When we got back in the truck, she started it up and it was just running rough with hardly any power. My first thought was someone dumped something into the gas due to her amazing parking, but there were no smells or residue of anything near the gas cap when we got home only a couple miles away.
When I got home I ran my code scanner and found 300, 301, 305, 307, and 308. I dumped a bottle of ISO-Heet in it, let it sit for a bit then cranked her up and ran it for a few miles to the gas station and filled up...about 25/26 gallons, I don't remember...I was a little above 1/4 tank when this all started. No change in performance and the codes were all still the same. I pulled the MAF, it looked clean, but I wiped it down anyways and threw it back in. No change. I then changed all the plugs. This took care of 301 and 305 but 300, 307, and 308 were still coming up. I then picked up two new coil packs for cylinders 7 and 8, threw them on and still no change.
I sat with it running on a flat surface for a little while revving the engine randomly for about 15 minutes, during this I noticed a fast tapping noise at about 3400 RPM, it went away quickly with no changes in the gauges on the dash. I cant really tell where it's coming from, but kinda sounds like its under the middle of the truck. While sitting there I ran the codes again, and now its back to 300, 301, 307, and 308. I'm now at a loss of what to even look at...
I've also checked the voltage coming off the harness at the connector to the coil packs...just under 11 volts. I've searched all over for what that voltage is supposed to be, but have failed miserably in my searches.
View 6 Replies
Advertisement
I just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
View 6 Replies
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 Replies
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
SO this truck came into the shop yesterday with a really bad misfire. pulled the codes and got a misfire codes for cylinders 1-6 and also p1450 (unable to bleed fuel tank vacuum) and p068a (pcm/ecm power relay de-energized too early) i found a TSB related to the issue, TSB 10-25-7 i did as the tsb told me to do and pulled valve covers to check out the rocker shaft rollers and inspect for any signs of surface deformation or fatigue. they were fine on both sides.: ive got spark in all cylinders. fuel pressure was right around 55-60 the gauge was fluctuating pretty good. checked for bad fuel or water in fuel ect. fuel seems to be good. pulled O2s incase of plugged cats still ran like crap.
View 13 Replies
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
View 6 Replies
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
I have spent alot of time looking through threads about v10's misfiring and have not been able to resolve my issue. I recently purchased a 2000 v10 f250 with about 220000 miles on it I bought it knowing it had one miss fire but now I have a total of three. Te truck has no problems accelerating but at a little over 40 mph the engine shakes quite noticeably and after 60 i5 seems to smooth out. After alot of reading I replaced all of my plugs and ignition coils, ran a can of sea foam through my gas tank and my intake with no change to the miss fires. I have started my trials with the fuel injectors by switching them from miss firing cylinders to ones that aren't. Some other information is my truck has no egr on my intake.
View 4 Replies
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 Replies
While driving into town during a recent snowstorm, my truck started to misfire quite badly. The check engine light started to flash and then remained on as I went to the auto parts store. The code indicated cylinder two misfire. I don't a few things of dry gas in the tank and let it run for a few minutes which seem to solve the problem.
Since then, however,every time the engine gets even a little bit wet it starts to bark again. It usually lasts a few minutes then goes back to normal. Typically, I would have replace the plug wires. When I lifted the hood of my truck I realize I knew nothing about it.
View 2 Replies
So basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
View 3 Replies
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 Replies
So my 2008 accent is my daily driver. I'm nearing the 300,000 mile mark but the last 100,000 miles have been plagued with random multiple misfires. I have changed the cables, crankshaft sensor, plugs, and I've been through numerous costly coils (I keep 4 with me). All listed parts were most recently changed at the same time. Why do I misfire on nearly every commute and get stuck operating on 3 cylinders?
View 11 Replies
I read in a thread about how fog lights need the auto light sensor or something in the kit to be installed and flashed.
My truck is a 2012 f250 XLT that I bought left over from a podunk town IN illinois. It does not have fog lights but it Does have automatic head lamps. So Im very confused on what kit to order to add fog lights to my truck.
View 3 Replies
2012 F-250 6.2 gas 4X4 SC/SB: when I run WOT, or near that, from a slow speed, I hear a short "hiss" between the 1-2, 2-3, and i think 3-4 shifts. I can also feel that the engine eases up quite a bit during the shift, and it is kind of a slow, soft shift. It has about 2,000 miles on it. I bought it in March 2013 as a leftover (great price!). The door sticker says it was manufactured in 4/2012, so it sat on the lot for quite a while before i bought it. But i don't remember it doing this when it was newer (~500 miles).
With the lite weight of this configuration (it is an XL so it isn't even carrying around 4 speakers ha ha), and me rarely carrying a very heavy load (yet) or towing anything, I rarely have to step on it very much in normal driving... it hardly ever gets above 2,500 rpm unless I am just running it faster for fun.
The hiss and slow shift happen at any transmission temperature. Of course, it never has been above the left side of the "gear" pic on the temp gauge, where it always is after full warm-up. Well, I'm hoping it is just shifting soft like this because it has "learned" my lite-foot driving style (even when I'm in a hurry of course the engine rarely has to work very hard).
View 3 Replies
I've got a 2012 F250 XLT with AM/FM/CD/AUX radio, and the display is not working. The radio functions fine, as do all other electronics on the truck, but the display is dark. I've tried pulling Fuse #29 in the passenger kick panel, and it looked fine. Is my radio toast?
View 3 Replies
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 Replies
I just purchased a 2012 F250 XLT with the 6.2. It has 38,000 miles on it. Yesterday I noticed, when coming to a stop, the idle will sometimes drop below 500. The engine will stumble a little, then the RPM will jump up to 1,000. Twice it has stalled on me. When it stalls, the engine will restart just fine. No codes in the computer or warning lights on the dash.
I will be bringing it back to carmax, as it is under their 30 day warranty still. Hopefully they will be able to figure out something. I am thinking either the TB needs to be cleaned, or there is an issue with the canister purge valve. I saw the TSB for the CPV but it doesn't cover my truck.
View 6 Replies
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
View 11 Replies
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 Replies
