Ford Super Duty (1999-2016) :: 2012 F250 6.2L - Drone / Vibration When In Drive Between 1600 - 1800 RPMs
Sep 23, 2013
My 2012 F250 6.2L (Gas) engine developed a noticeable drone/vibration when in drive between 1600 - 1800rpm. RPMs above and below that range is fine. But when accelerating, as soon as the RPMs reach 1600, you can feel a slight vibration through the gas pedal and a noticeable sharp draon/moan up till about 1800 or 1900 rpm, then its normal.
I took it to my ford dealer and took the service manager out for a test drive. He said that there is a drone and slight vibration withing that RPM range. He thought that the engine mounts may be loose. But aside all that, he felt something was off and wrote up the service order.
When to pick up the truck and now the service manager changes his tune and said that the drone is normal and happens on all 6.2L super duties.
To be honest, I have the feeling he is pulling my chain.
View 6 Replies
Advertisement
Is there truely no cure for exhaust flutter on a 2002 f250 V10, bedsides putting on headers??? I have the the sound at shift points around 1800-2200 rpms. Sounds great before and after these points....
View 14 Replies
2012 Camry SE 4 cyl, 56K miles ... Happens in all gears, in normal and sport mode “under light acceleration” at 1600-2000 rpm.
Sitting in driver’s seat I hear a drone which sounds similar to the engine lugging we hear briefly at around 1000 RPM. In the 1600-2000 RPM range it is very annoying because this is the cruising range on highways. Sometime when going up a slight incline it can be felt through the accelerator.
When seating in back seat on passenger’s side, it sounds similar to a bad muffler/resonator and is very audible. Spring loaded exhaust couplings in front of muffler and between front pipe and converter are not seized. All rubber hangers are there. Installed “B-quiet” sound absorber in trunk going from spare tire well over top of muffler and up rear quarter panel which did not work. Nothing is touching the exhaust under the car.
When idling the exhaust produces a noticeable putt-putt sound. Toyota rep (not dealer) went for a ride with me and feels it is typical of a car “for this mileage” (same as dealer told me). I stated it did not do it before and was told cars wear in and after a while characteristics change.
View 2 Replies
I have a 2000 f250 crew cab short bed 7.3 on a 6inch bds lift and 37 inch tires. When I accelerate pretty much any load above 1200 rpms I can feel a vibration, kinda feels like it may be coming from the front left but I'm not sure. I have heard that a wheel bearing going out can cause this, would this maybe be what's causing it?
I thought wheel bearing because it kind of sounds like there's a howl when decelerating, probably when accelerating as well but the trucks too loud and I can't hear it. or also have heard motor mount gone bad, I've also heard ujoints but the ujoints were done this summer. the front ujoint is bad but the front driveshaft shouldn't be turning when out of 4x4 and hubs unlocked.
View 4 Replies
The engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 Replies
I plan on putting a catback exhaust on my 2016 F350 6.2 gas engine. I have always loved the sound of Flowmaster exhaust but over years have started to become slightly annoyed with the drone in the cab. Is there a exhaust system out there that is capable of sounding like Flowmaster but without the in cab drone.
View 2 Replies
have a 2006 Forest River Lexington 255 GTS on a Ford E450 chassis. We purchased it used 2yrs ago from a private owner with only 20,000 miles. It had a slight vibration which got worse over 60 mph. All tires were replaced and when that didn't work, took to a different dealer to have road balanced. We drove the home some and the vibration got worse starting about 40 mph. We took it to a local truck repair shop that does drive-line work. They have replaced the transmission tail housing with a bearing it, had the drive shaft rebuilt including new u-joints and re-tubing the front driveshaft. The vibration now is worse than ever..so bad that it's not drive-able over about 30 mph.
View 7 Replies
I've got a 99 f250 5.4 that runs like a top. In the last 6 months I've been chasing a little problem. It doesn't happen all the time but seem to be happen more and more. While driving any speed If I let off the gas the RPM's hold at around 1500 then surges down to 1000 then back up again to 1500.
Does that 2 to 4 times then all good. Give it gas again it does it again. It kind of does it when it wants. Could be fine for a trip around then next trip it acts up again. Checked a lot of the vacuum lines, PVC valve and replaced the idle control next to the EGR valve. EGR is next.
Idles and runs fine except the surge thing..
P0401 code as well.
View 11 Replies
I have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 Replies
1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
View 4 Replies
Ok, I have a 2004 F250 FX4 4wd 5.4L with almost 160K miles.
Sometimes, mostly when it's hot, and I go to restart it, it will crank and crank and crank, so I let off and then try again and it will start. Then other times I will have to do it 3-5 times before it starts, or it will start with real low RPM's for a second then cut out. I have been told this truck does NOT have a Fuel Pump Driver Module (My previous F-150 did). So I'm thinking the fuel pump is just temperamental. Having this issue or replaced a fuel pump before? What brands, places, etc. are good to buy at a decent price?
I tried to look online and was confused about a "midship, rear, and center tank". All I know is my truck is an extended cab and has about a 29 gallon tank.
View 6 Replies
I have a 2011 f250 6.7 and I have a very bad vibration between 40-50 that seems to peak around 45-47. It also starts again at 80+ . the dealer told me they could not find a problem. Then another told me its normal. The tire shop around here told me the tires were shot so I bought new tires. No luck. It does not affect it if I change gears.
2011 f250 4x4 6.7 SWB. 140,000 miles
View 11 Replies
I have an '03 F250 Super Cab, 7.3L PSD, 4WD. I've started getting a large vibration between 40 and 60 mph. Started after driving on the PA highways towing a trailer with a car and hitting several deep pot holes.
I have had the wheels balanced, rotated, balanced a second time by a different shop and had them perform an alignment - Still No change.
The garage I took it to said the hubs were shot so I had them replaced - supposedly with Moog, lifetime warranty hubs. Still - No Change.
The tie rods and steering linkages are a year old, so unless something was damaged (visually, they look good, and feel tight) it probably isn't them.
I replaced the ball joints around 80,000 miles and now the truck has 155,000 miles. They appear to be ok, with maybe just a little movement in the Passenger side upper.
If there is any movement at all in the ball joint, will it cause a vibration?
I plan to rotate my full size spare through all 4 corners this weekend to eliminate the possibility of a bent rim.
I have another set of ball joints and seals on order which should arrive next week. Probably next weekend's project.
View 9 Replies
I have a vibration in my 2001 f250. At about 45 to 55 it vibrates. I have changed u joints in the rear drive shaft. Pulled it again tonight. U joints look good, no play. I am going to pull the front shaft and see if it makes a difference. I did notice some play on the rear shaft where it slides. Could this be causing the problem?
View 4 Replies
My 05 f250 5.4 has developed a whine that is easy to hear in low rpms. I don't think it goes away with higher rpms, but instead is just masked by the sound of the engine. It will do this in drive, reverse, and also when it is revved in park. What this could be?
View 10 Replies
I have 2005 f250 5.4l 3v that was having miss problems between 1200 and 2000 RPMs. Changed VCT solenoids which worked, but then could hear chain hitting cover when powering down throttle on left side. Figured chain tensioner was bad, so tore down and removed timing cover. Found left chain was tighter than what seems normal, and right side had huge amount of slack. While taking off tensioner on left side, something happened to fast for me to see it, and still not sure if what happened wasn't just my imagination. I thought that the chain moved very fast for an inch or two. Anyways, I watched how to video on timing the 3v, but I am very confused about it. The left bank seems to line up on timing marks perfectly, but the right chain is off by at least 2 1/2 links. Not knowing any better, I removed three rockers on left bank (2 intakes and 1 exhaust) but only removed two intake rockers on right side. I don't know what I am doing and getting scared.
View 1 Replies
I have a 2003 F250 with the 5.4 and I believe I am having a fuel delivery issue. I took out yesterday and stopped to get a drink at the gas station, came back out and the truck wouldn't start long enough to idle. It would start, barely bounce off zero rpms and die out. I checked the fuel interia switch and it was down. I tried turning the key back and forth thinking it might reset the fuel pump or something and that didnt work. I get the truck towed home and couldn't get it to start last night. I go out this morning and it starts, come home from work and now it won't. This happened about 2 years ago and I never did anything about it, but it took 2 years for it to happen again.
View 2 Replies
I recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 Replies
My elderly neighbor has asked me to re-attach his drive shaft on his F250.
Said his wife was driving and it broke the u joint or something, and he has gotten it repaired and wondered if I could put it back on. Has been sitting for a bit from what he said.
Just need to know, how I should clean up and or grease? the end with the boot on it. before I put it together. The boot looks to be zap strapped, is that standard?
View 2 Replies
Love my 03 lariat Super Duty, King Ranch. Just found out 4 wheel drive is not working. Checked fuses, next going to look at the vacuum system, make sure its working. New to the Diesels but going to work at it and learn at the same time. 2003 F-250 4x4 ....
View 5 Replies
I have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 Replies
