Ford Super Duty (1999-2016) :: 2011 F350 - Tire Pressure Monitor Fault Code
May 9, 2017
So I scored a real deal on a set of Michelin on same size 17" OEM wheels that were taken off a brand new 2017 F-250 at about 100 miles. I installed them on my F-350 and had no faults show up. The tires had been marked as to which corner they had come off of so I put them on the same corners of my truck.
After driving about 50 miles I got a "Tire Pressure Monitor Fault" code. I pulled out my owner's manual and followed the relearning procedure exactly but I get the two beeps and the fail retry message from the left front. I have tried three times and get the same result.
Looking for info if the 2017 F-250 sensors are compatible with the 2011 F-350? Have I overlooked something? I habitually manually check my tires anyway, is there a way to disable the TPMS? Is it time for the dreaded trip to the dealer?
View 14 Replies
Advertisement
I've looked at this 10 ways to Sunday, but the play on words have me questioning if it is the same thing. My truck says Tire Pressure Monitor Fault. I have a 2011 F350, if that makes a difference. I checked all my tires, they are about 80psi each, front and back. What could be the problem? Is it something to take to a Ford Dealer or something I can fix myself?
View 7 Replies
Just got larger tires on my truck and tire pressure monitor light is on. How would I go about resetting this?
View 14 Replies
I have a 2010 F250 Super Duty with 18" factory wheels. I started having intermittent Tire Pressure Monitor Faults. My research lead me to believe that the seven year old sensors were probably running out of battery life. So... When I had new tires installed I also had new FoMoCo sensors installed and I purchased a FoMoCo tool (TPMS 19) to train the new sensors. My problem is that I cannot get the sensor training process to work. When I put the truck into the train mode and try to retrain the LF tire, nothing happens and eventfully the horn beeps twice and the dash reads that the training failed. Where is the receiver that the sensors communicate with? Could it be bad?
View 9 Replies
I have a 2010 F350 that has been throwing the "tire pressure monitor fault” on the dashes info center. Here is where it started. I purchased new wheels, tires and sensors a few weeks ago. I put them on and they were fine on the way home because I assume that the stock ones where still being read (they were in the bed of the truck). Put the old ones in the garage and then while driving to work the next morning I got the message. I tried to reset or “learn” the new sensors that night with no luck. There are two ways to get my truck into learn mode. One uses the hazard flashers then releasing some of the tire pressure until the truck horn beeps. The other method is a series of break pumps and turning the ignition from on to off then using the TPMS tool that apparently comes with the truck.
The truck went into learn mode every time with either method but it would never recognize the new sensors. After attempting everything on the sensors I checked to see if for some reason the trucks actual monitor was in a “fault” mode. Last night I tried relearning the old stock sensors with great luck. They all were recognized… for about 10 minutes. After getting them to work I left the shop I work at and on the way home the "tire pressure monitor fault” came back again. So just in case something had been in sleep mode when I did it I pulled over and reset them once more. Again with great luck… until this morning on the way to work again it went back to fault mode even with the stock wheels still in the bed.
View 1 Replies
Got a 'Tire Pressure Sensor Fault' message a few times on the way back from Florida. Tire pressures were all fine. Hate that it doesn't say which monitor has the problem. Anyway... it comes on, but after a few minutes goes back off. Saw it a total of three times over the course of 1,000 miles in two days. Is this the sensor failing and requiring replacement? Or is the system itself starting to fail? Would ESP cover this?
View 6 Replies
I have a quick question regarding tire pressure. Where we work, we have a 2005 F350.
Stock tire pressure for stock tires 275/70R18 states 65 PSI for the front and 75 PSI for the rear.
The truck currently has 295/65R18 tires all around. They are some sort of Wrangler tire, not sure of exact model, but they are more of a all-terrain tire. The truck sticks to the road though.
What would be the recommended cold tire pressure with these? Can I stick with what the stock tires would be?
View 14 Replies
I was running tire chains on my front end and broke the wires going to the wheel (I know ,not smart) . Immediately Service AdvanceTrac, Hill Descent fault, ABS light came on. I took it in to a shop and they repaired the wires but lights are still on and won't clear. Buttons on the dash wont work either. Messed up the sensors maybe?
View 1 Replies
Well, at a little over 10k I have my first issue. My monitor displayed a Tire Pressure Monitor Fault. All tires are OK. Light won't go out. Guess it just earned a trip to the dealer.
View 14 Replies
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
View 14 Replies
I have reset my tire sensors twice and the low tire light would still come on, so I called the dealer today..he said you have to set the tire pressure to what is on the door jam.
65 psi front and 85 psi rear. I did not know that. I had been setting all to 65 psi.
View 3 Replies
I'm getting a random 'no start' fault which I think is related to a clutch position switch. The dealer tells me the clutch pivot bushing and master cylinder push rod are worn out, which is causing the switch not to close when the clutch pedal is depressed.
1993 F-350 7.3L Diesel 5 Spd 4x4, Std Cab, 8 Box.
View 1 Replies
2014 f250 - tires call for 75 fronts, 80 rears. I have been running 60 in all four corners for 6 of the 7 months I have owned the truck. Just turned 8000 miles and yesterday morning the low tire pressure light came on. Checked tires and all good. What might be happening?
View 11 Replies
Went to leave for work this morning & got a "low tire pressure" warning...checked at work (isn't it always the last tire you check?), going to have to keep an eye on the left rear..was down to 45
with all the money we spend on these rigs, why can't put in a tpms system that would allow us to see WHICH tire is low?
Any aftermarket system that allows monitoring of INDIVIDUAL pressure? (ultimately, it'd be nice to get a 4 axle system that would "communicate" with the trucks (very basic) system, but also allow monitoring of my RV axles as well)
View 4 Replies
Just got a new-to-me 2006 F350 Super Duty XL with the 5.4L V8 and 5-speed auto. I haven't had a full-size truck in a few years and forgot what I was missing!
When I bought the truck, all gauges were inoperative except for the fuel and oil pressure gauges. The previous owner told me they would work intermittently and at some point just stopped. The usual warning lights - ABS, CEL, and "the wrench" - were all lit, and from Googling and searching this forum, it looked like an easy fix - probably a pinched or frayed shifter wire, or possibly a cluster repair.
I took it home and did a self test on the gauges. The "sweep gauges" made everything swing fine, so I was thinking it might not be a problem in the cluster. I pulled the steering column apart, removed the Tow/Haul overdrive wire from the plastic retainer, re-ran it with some slack, taped the end where it comes out of the shifter (even though I saw no breaks/frays) cleaned the connections, gave it a dollop of dielectric grease in the connector, and put it all back together. VOILA - GAUGES and no warning lights! You can imagine the touchdown dance in the driveway.
Fast forward a few weeks and....back to no gauges and warning lights lit. Figuring the overdrive wire had finally given up, I ordered and installed a replacement shifter figuring it was an easy and cheap fix. No joy - same problem. Tried cleaning and reseating the connection. Nothing. I've searched FTE like mad and it seems like 95% of the problems are with the wire exiting the shifter fraying and/or blowing a fuse, but this is a new shifter. I've also checked fuses #2, #24, #33, #36, #41, and #45 (some referenced #19 but I don't have a fuse there). All were unbroken - just put them back in and reseated firmly. I did a code pull via OBD2 and have a "rear catalytic efficiency degraded" code...not sure if that's related, but figured I just had an exhaust issue.
I may take the dash cover off and try to clean and reset the connections on the gauge cluster, as well as do the same for the PCM. Is it possible that the tow/haul overdrive wire to the PCM (where the shifter connects to) is bad? How to test and/or replace if it comes up bad?
View 14 Replies
Ok, so I got this new Superduty that requires 80 psi in the rear tires and 70 psi in the front for 17" tires. What psi are you guys with similar vehicles using when driving around unloaded?
View 13 Replies
How to shut off the Low Tire Pressure message? My tires are at 65-70 pounds and the message still shows up at every start up.
View 6 Replies
I just bought a 05 F-250 156" wheel base crew cab 6.0 with LT305/70R17 Nitto Terra Grapplers. What will be the tire pressure. Manufacture label on truck says 75psi cold but the tire itself says 65psi max. I mostly drive without a load also.
View 2 Replies
What is the proper tire pressure for these trucks (F250)?
Sidewall says max is 80 PSI.
Door jam says 71 PSI.
This is coming from a guy who has traditionally driven passenger cars and trucks. I've never even gotten CLOSE to advertised max PSI ratings. 71 seems awful close to max PSI.
View 4 Replies
Every time I put the headlights on or just the running lights within 15 minutes it trips the tire low pressure warning, how can the 2 be connected? Turn the light switch off and anywhere from 5 to 20 minutes the warning low pressure light turns off. I know take it to Ford but I'm out of State presently and l'll just wait till I get back home next month.
View 9 Replies
So we had a subzero weather week last week and on one of the below zero days by low tire pressure light goes on - on my dash. I've checked all 4 tires and they are not low. Do I have a bad sensor? Or is the cold causing this?
View 14 Replies
