2011 F-350 XL, I can hear a squeal coming from the front brakes when rolling forward slowly, believe the pads are dragging on the rotors. If I touch the brake pedal the squeal stops as it does when I turn the wheel. Took the calipers off and greased the slide pins and put it all back together, still got the squeal. What don't I know???
View 9 RepliesAt low speeds, I notice a squeel sound in all four wheels. Ford tells me that it is due to the type of metallic pads they use and is essentially brake dust noise that warrants no repair.
Any after market pads that are good quality for towing heavy loads, yet aren't metallic in composition? For instance, are porcelin pads a good choice.
I have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
I have a 2011 F350, with a 4 inch Rancho Suspension lift. Ever since the lift kit was installed, more commonly when turning to the left than right, the anti lock brakes come on and the traction control light comes on/flashes. without even stepping on brake pedal.
It seems to happen when the wheel is at about 80% of max turning, about 15mph. Both wheel hubs and sensors have been replaced. road tested with Ford tech , he watched the speed sensor input while hooked to the computer and all sensor are reading correctly.
Today I went in a constant circle and can make it do it non stop, and when you try to press the brake pedal while the anti-lock (grinding/chattering) noise is happening, it only gets louder.
I have a 2007 F350 XLT, Super Cab, chassis cab, V-10, 4x4. I ordered it new, it now has 97,000 miles. It is equipped with a 9' aluminum flatbed. I tow it behind my motorhome and also carry a truck camper (not when towing it!).
I don't think the front brakes are working 100%. I have 2 sets of wheels and tires (19.5s for hauling the camper). Every time I change over, I check the brake pads for wear. Over the first 80,000 miles there was very little wear on the rear pads. In 2014 I had almost a complete brake failure while traveling. I took it to a Ford dealer, and they determined the brake booster was bad. They replaced the booster and flushed the brake system. I didn't think the brakes felt right afterward, but I carried on. By 95,000 miles, the rear brakes were worn out. I feel like the rear brakes are doing most of the stopping now, thus wearing out much faster than they were.
I just ordered a set of service manuals for the truck (9.5 years late on that!) hoping to figure out something. I like the truck, it meets my needs, and I hope to keep it quite a while longer. I took it in to the local dealer to replace a leaking rear pinion seal. They found and replaced the worn pads. I trust them to the extent that the pads were worn, as I had already noticed an acceleration in wear. Local dealer that replaced the pads has no idea what could be up. They did clean and lube the front calipers at the same time, but I noticed no difference in brake feel. Stopping power is definitely worse than before the brake failure/ booster replacement.
What might cause this? The only things that come to my mind is a problem with the proportioning valve or maybe the master cylinder. I don't know much about the details of the ABS system. Is there anyway that might be causing the issue? I would rather not just start throwing parts at the problem...
I have a 2002 ford f350 triton 5.4 V8. I just put front brake pads on my truck today. Started driving around and i could smell burning brakes. Stopped and alot of smoke was coming from my brakes on my front passenger side but nothing from the front drivers side. Replaced all the brake pads on the front. What is making them so hot?
View 8 RepliesWhen on my 2-post lift my front brake lines on my '11 4x4 are pulled TIGHT, like stupid tight. It's also dumb that the soft line points UP 'cause it gets tugged down to a brutally tight 180.
I've got the front lift pads under the control arms, too, but near the very rear of the control arms so the axle isn't even dropped out all the way I don't think.
There's a bracket down near the bottom of the coil springs that could just be sectioned/lengthened, which I think would alleviate my issue. I'll be working on this soon.
What manufacturer builds a vehicle that yanks on the brake lines under full suspension droop? Shouldn't this be on an engineer's final checklist before the vehicle is released? Oh wait, they gave that task to Team TTB and Engineering Group TFI Or maybe they gave it to the same Audi team that designed the Allroad with airbags that can be damaged if you don't "lock" them out before lifting the vehicle......
Truck is 2011, F350, 4x4 CC Long box with a 6.2, 124,000 km on it. Was driving home last night towing my jet boat when I heard a sudden noise from the front end, kind of shudder, first reaction was a flat so headed to the curd. No flat, nothing running hot, no play in wheels, all looked good underneath the front end. Pulled out and drove away, got about 15 km and it happened again, looked all around nothing obvious so pulled out and drove home (25 km) no issue.
This morning wanted to investigate further. Drove truck down the block and heard a definite rotating type sound. Not a grinding more like a scrape sound. After a minute it went away. Went into a parking lot and drove in tight circles but no strange noise. Found that the auto locking hubs were not working but hub would lock in manual. No strange noises with hubs locked in either.
Jacked up truck rotate front wheels, no sound and no play or wiggle on either side. Pulled the hubs and the passenger side had water in it. Hub was not rusty but it didn't look as good as the other side. Not sure how water got there as I have never driven in water, although I am not original owner but have had it two years and put 25,000 km on it. Could the water have gone in deeper and caused a bearing to fail?
I've got a 2011 F-350, when i'm on the driving over 60 mph i hear this humming or buzzing noise coming from around the dash. It kind of comes and goes depending on the wind direction or if I'm passing a semi. Thinking it may be coming from around the windshield seal.
View 4 RepliesI have an 07 350 6.0 was plowing last night toward the end of the night i herd a popping coming off the front end of the truck. My esof does not work so I manually lock the hubs and then turn on the 4x4 from the dash when I want 4x4, ok so after the few pops I heard while slightly turning I straightened out and all seem ok till I pulled outta the parking lot started driving and i had a noise kinda sounded like driving on a flat while at speeds at around 25-35mph so I got out unlocked the hubs drove it and it drives fine unlocked. so what I've done so far is while hubs unlocked climbed under it spun the front driveshaft by hand and spins freely. When the truck is rolling with no issues i locked the hubs left the switch in 2wd turned the wheel and started to make a turn and POP loud and shakes the truck violently it feel likes the steering and the truck is binding when trying to turn.
View 4 RepliesI have a 2001 f350 4x4 with7.3 diesel...I have recently noticed a low grind like noise coming from the right front. I have troubled shot the issue and I am 100% sure it is the wheel hub assembly. Did I mention I am running 37x13.50 tires..and now you say no it is the hubs...and they are the original hubs. My question is every thing I look for shows ABS is on my truck... I look at the hub and don't see it.. so with the Dana 60 front does it have ABS or not? Also, should I go motorcraft, Timken or moog wheel hubs?
View 1 RepliesIt seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
2004 f350 lariat Key fob slowly started not to work until it finally quit. Thought it was the battery but changing it had no change. Do the fobs go bad and need to be replaced?
View 11 RepliesMy 11 cc lb 4x4 6.2 has a clunking/loose sound coming from the front end. It is prominent when going over small/medium bumps but not so much large bumps. I have had my local dealer and a couple local shops look at it and they all say everything checks out. It definitely seems like something is loose in the front suspension. I just put new Gabriel max control shocks on all four corners. I have no play in wheel bearings or ball joints. Tie rod ends also look fine.
View 12 Replies2011 F250 6.7L Powerstroke, automatic tranny, Electric Locking Diff
When I engage the On the Fly 4WD switch the indicator panel says "shift to 4x4H in Progress" and everything seems fine but if I am not moving forward when I shift the 4WD doesn't engage. The engine revs up but nothing happens. When I release the accelerator the transfer case bangs like it is going to rip out of the truck. In reverse it is even worse. I am lucky that I didn't gun it or I could have done allot of potential damage. All my other Ford 4WD vehicles engage immediately from a full stopped position. This is quite of troublesome because if you have to shift when your stuck in the mud, your still stuck. If I shift while moving forward it works just fine.
My question is: Does this particular model (2011 F250 6.7L Powerstroke with an automatic tranny) have to be moving forward in order for the 4WD to engage?
I have a 2011 F-350 Diesel. It started making a strange whining sound when I start it in the morning. Very random and only does it when it's 0- -4 c. Took it to the dealership and they said its the cooler fan clutch. Got it replaced yesterday, and this morning I started it up and the whining sound was back. It also had a weird vibrating sound. What it could be?
View 10 RepliesIt's an 04 F350 6.8L This past winter when it was cold I would start it up and it would rock forward and bounce back as is you shifted in to park while rolling. Now that it's warmed up it won't jerk forward but the whole body shakes only at start up. As much as I like the idea of of the raw torque being so powerful the truck twists with power I don't think that's the case.
View 5 RepliesIve got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 RepliesGot a problem with my F350 diesel truck's braking system. I pull a 5th wheel and last trip almost burned my breaks up coming down long hill due to having no breaks on the 5th wheel. Had a problem early on with the lack of trailer brakes and module was replaced under warranty. Bought a new module this time and it did not fix the problem. Have braking power when I use the module brakes (Hand) but not when I hit the foot brakes. Have checked the system with a meter and have good voltage with hand break but not with foot brakes. Have a good meter (voltage) read with hand breaks and faint read with foot brakes applied. Also have a faint pulsing read on test light with no brakes at all just key on.
View 2 RepliesI use a bottle hanging like an I.V. drip to flush the Brake Fluid in all my cars. I can pump all the old fluid out, as well as the air. My Superduty 7.3 has a good solid brake pedal after the flush. It seems to me the rear brakes handle 60% of the stopping load. Its been like this for so long I'm not sure if it's ever been different. i then go to a gravel or wet road and test the rear abs, and it seems o work, but definitely has a squirrely feel. I did some strong pavement stops with speed, and it stops, no skidding. Is that the way it should be?
View 14 RepliesThe electric windows in the front seem to be very lazy. When you depress the button, it goes down slowly and eventually stops halfway. Does it need a lube?
View 1 Replies