Noise question. I have a 2011 super duty f250 xlt, and my question is I have a grinding noise that does not sound metallic and only shows up when its below freezing, only in drive and for about 50 yards.
View 6 RepliesMy 2011 F-250 diesel will not start when it gets to be about 85 to 90 degrees. In cold weather (I live in South Florida, so by "cold" I mean 50 to 70 degrees) it starts up just fine and gives no problems whatsoever. However once the summer months hit it more often than not it will not start. I've taken it to the local Ford dealer and when they run diagnostics it doesn't report any problems. I admittedly don't use the truck very often and it will at times sit for a couple months without use. Could that be a cause of the problem? What the problem might be?
View 1 RepliesI have a 2011 F250 with ac problems. When you start it in the morning and turn the ac on it only takes a small amount of time for the air to start cooling. If you turn the truck off then start it again after driving to town the ac blows hot air out up to 4 minutes (yes I timed it) before it starts cooling. I took it to a local repair shop and the first time they said it only had half the freon it needed. The charged it and off I went. Same problem. The second time they informed me the fan clutch was not engaging and replaced it. I picked it up and the first time it was turned off and back on it had the same problem. I am scheduled to take it back to the same repair shop on Monday.
View 1 RepliesI have an 02 250 5.4. 103,000 miles. My truck at random times will not start in below freezing temps. Turns over just fine but Acts as if a frozen fuel line. I can get it running by pouring hot water on the fuel rail or a shot of starting fluid or sometimes both. It's been going on about 3 or 4 weeks now and I have ran through 4 bottles of dry gas with about 15 gallons each time. Also have replaced fuel filter and fuel pressure regulator. I'm 99.9% positive the pump is working and there are no leaks in the lines or holes in tank that I can see. My next step is to drop the tank and clean it out but trying to avoid that.
View 14 RepliesMy 03 F250 7.3 is making a grinding noise when I let my foot off the accelerator and coast in 4x4, I replaced the hubs with new warn premium hubs and it is still making the noise. The noise does not occur when I take it out of 4x4.
View 2 RepliesI've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
Okay this is what I got; I recently purchased high mileage 2004 F250 Super Duty short box super cab 5.4 liter. Came with manual 4x4 handle on the floor so no 4 wheel on the fly and this eliminates the vacuum for the auto hubs so this will not be part of the problem. When engaging the hubs and ONLY when engaged the driver side hub grinds. The 4 wheel drive works but it sounds like its ready to grind itself into oblivion. I did pull the hub and the grinding was gone, I happen to have a spare hub that is good and the grinding returned.
I have jacked it up and made sure I have no play in the wheel itself and the axle knuckle on the axle shaft. Some say remove the front drive shaft? Or turn the wheels all the way in one direction engage the hubs and check for binding? I will do this in the morning, but what does that confirm if it not the hub. Could it be the passenger side echoing across? On my 99 Super duty I kept hearing moaning coming from up front like the breaks were shot and if you stuck your head out the window it was the back echoing to make it sound like the front.
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
The problem I am having is that there is a grinding noise when in park. If i shift into gear then it is fine but shifting back to park very big grinding noise. At the same time I have the Speedometer and fan for the heat not working as well as the heater for the seats.
This problem is so bad I am afraid to drive and get stuck somewhere. I have checked the starter and it is tight ad secure. all fluids are fine. Not sure what this would be? This is the single vehicle i have for work and family.
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
I just bought a 06 F250 King Ranch and the information center on the gauge cluster just shows the current odometer reading. When I press the information button that is supposed to toggle between trip mileage and avg mpg just the odometer shows. This truck was vandalized (bought from auction) so I am wondering does it have a XL cluster so I am asking are all the clusters different between XL, XLT, Lariat, King Ranch, etc and I have the wrong one installed or maybe there is an issues with my information center.
View 3 RepliesSo after this weekend's hurricane my 2011 f-250 started to making a noise when I accelerate. I don't know if water got in some where. But there's no MIL light coming on.
View 11 RepliesI picked up my 05 F350 dually 5 speed w/ the 6.0 powerstroke motor in august... It only had 38k on it when I bought it... its got 43K miles on it now...
Ran great in the warm weather but ever since it got cold out its been a struggle. It was running rough on the way home and kept stalling while i was driving it.. (acting like it was starving for fuel).
I went and replaced both fuel filters and started the truck... let it warm up and it stalled while sitting in my drive way and haven't been able to start it since...
I have fuel additive in it but since I don't drive it all the time (maybe 3 times a week for 30 miles) could it be possible that the fuel is gelling?
I was going to check the EGR valve tonight...
Just bought my first Ford. Its a 2015 F250 Platinum. Im at 1400 miles and Im becoming concerned because when I start the truck for the first time in the day, no matter how long I let it sit and warm up I am noticing that on the first couple of miles of driving I hear a high revving sound as I accelerate and it seems to quick shift during those first few miles.
As I continue to drive the high rev sound just fades away and all engine sounds and shifting are as normal as can be and will remain that way until the truck has been sitting for an extended period of time and is cold. I thought it had something to do with tranny temp but this morning I let the tranny warm up to about 115 deg in neutral before taking off but still had the high rev for the first few miles. I have never owned a ford nor have I ever owned a heavy duty truck, hoping this is normal.
6.2L F250 truck is just shy of 60k runs good however on cold startup there's now a pretty loud ticking noise for a short period (30 seconds) until it warms up then it slowly goes away. Once its warmed up there isn't much of anything.
Did these have exhaust manifold gasket problems like the 5.4? Hoping that's it if not, any other common problems that would make that ticking noise and then go away quickly once the engine is warmed up.
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
I have a 2001 f250 4x4 about 4 months ago I replaced my pass. side front wheel bearing unit and here recently about 3 to 4 weeks ago I get a grinding/ rubbing sound when ever I turn right it gets louder the harder the right turn I do not seem to notice it as much moving at speed but driving through parking lots and slow speed right turns I can hear it. I have checked everything and nothing is loose and I can not see any signs or fresh rub marks on anything. I am getting to the point of just buying a new unit and replacing the one I just replaced. What my problem could be?
View 3 RepliesI can't seem to get the engine temp to middle range on the marker, but yet my heater blows "to me" hot air. Even while sitting in idle for extended amounts of time I cannot get it to "operating" temperature. I would think if my thermostat was stuck open my heater would blow either cold or slightly warm air. I have the 5.4L engine with knn air filter and no cats.
View 14 RepliesWent on a 400 mile trip today and noticed some strange noises. The rig is an 06 F250 lariat, V10, Zf6, SC, LB and only has 43k miles. It behaves normally except when coasting down a hill at 65+ mph, and it doesn't matter if I'm in neutral or overdrive, it makes a feint grinding sound that gets louder as speed increases. Maybe grinding isn't the best word to describe it, I'd say a cross between humming and light grinding. As soon as I give it any throttle or put any load on the tranny is goes away. It's really freaking me out as I just got the truck a month ago and I know the ZF6's are almost bulletproof.
View 14 RepliesI have a 2001 Ford F-250 with the gas v-10. Yesterday it started just fine as always. Today I get into it and it starts to turn over just fine then starts to make a grinding sound and the truck won't start. I have had a fuel issue in the mornings with once it started you had to barely press the gass to keep it running. But never makes a funny sound and always runs fine. This only last for a couple of min and then it runs fine for the rest of the day. The grinding is not the starter. I took it off and had it checked and it was fine.
The truck had been using oil. When I checked the oil level it was low but it was still on the stick. "I know a motor needs oil to run smooth but it's my dads truck and well let's just say he is not the best on maintenance". Also I smelled the oil and it does have a gas smell to it. So it definitely does have some gas in the oil. I tried to light the dipstick with a lighter and it wouldn't light. So not sure how much gas is in it but that's what I did.
So the question is, would something just in mid crank go bad and then not let the motor crank. Truck made no weird noises before this so I find it hard to believe the barrings just went out in mid crank and now it is shot.
Also I just checked compression on front cylinders.
Driver side read 75lbs
passenger side read 100lbs