Ford Super Duty (1999-2016) :: 2011 - Backup Lights No Longer Work?
Nov 8, 2015
I screwed up installing LED taillight assemblies in my 2011 SuperDuty and pinched a couple of wires against the body. The result of this (at least I think that this cause) is that my backup lights no longer work - neither the backup lights in the tail light assembly nor the reverse light power on the trailer plug. I have checked the fuses, etc. and nothing. I brought it to a local shop and they could not figure out the problem, either, but said that it was probably the "control module" that got fried when the wires got pinched. They said to take it to the dealer. The questions are, what "control module" might they be referring to, or what to check?
View 1 Replies
Advertisement
My 2011 f250 is stuck in park and the brake lights do not work. I have changed the brake switch but still wont shift out of park.
View 4 Replies
Recently removed a plow and wiring harness from my 00 F550 and now my headlights no longer work. The headlight plugs have an adapter that the plow harness plugged in to and it now appears I need some type of end plug on each one to complete the circuit. The problem is the dealer doesn't understand what I need and doesn't think there is such a part out there. Perhaps my thinking is all wrong.
View 3 Replies
1999 E-350 Super Duty (figured the problem would be the same for van/truck)
Problem: Backup lights don't turn on when in reverse.
Diagnosis: Changed the fused (because it was bad) but didn't fix it. The bulbs are both good. Brake lights, turn signals all work. I understand the backup lights are connected to the Neutral Sensor Switch. To test to see if the NSS was working, I put the van in Reverse and cranked... Van didn't crank (and likewise for D, 1-3).
So I guess the Neutral Sensor Switch works. The fuse works. The bulbs are good. Haynes doesn't have much as far as troubleshooting for this issue. What should I look at from here?
View 7 Replies
I have an 02 f350 XL. The other day it rained and all of my rear lights went haywire. All problems are out back.
- Step on brakes, high mount, and lic plate lights light up with brakes.
- Turn on marker lights and the high mount lights up and the tails and lic plate lights dim.
- Marker lights on, apply brakes, and the tails and lic plates lights go out on bed, high mount activates.
- Use turn signals with markers off and all of the rear lights including high mount flash..
- Reverse lights dim or dont work at all.
I have tried a new MF switch, checked all fuses. cleaned rear frame ground. took apart brake switch and cleaned it. non tilt column but checked wires. replaced flasher. unplugged brake light switch and headlight switch, problem is still there. removed trailer relays, no luck. checked all chassis plugs. disconnected TRS.
I should mention i have 12v cummins swap and a pcs with standalone harness. no problems over the last few months since swap until it rained last monday.
View 12 Replies
Have a 2012 350 cclb 4x4 6.7 lariat, interior lights don't work. Not with any door open, Not with switch. map lights work. We've checked every fuse in cab and under hood. What to check now ?
View 8 Replies
2011 SD 6.7 with factory remote start will start normally when the temperatures are above 20F or the vehicle is warmed up. If the temperature is near or below O F and the vehicle is cold soaked for 12 hours the remote start fails to work. Push the lock button and the lights flash, push remote start twice and the lights flash once and nothing happens. Subsequently can manually start vehicle with key without any delay or problems. Once vehicle is warmed up can remote start normally. Only recently have the temps been low enough in the area to experience this problem which has repeated 3 times. Unable to find any troubleshooting in the service manual for this.
View 7 Replies
I have a 2001 F350 and instrument cluster lights will not work. Fuses are good and the gauges still work just not the lights.
View 5 Replies
I have a 2001 f-250 that has dome lights that work on occasion. Mostly don't work. The inside dash dimmer won't turn them on. And they will sometimes work with the rear doors opening. Not the front(4 doors). The cargo light comes on all the time. So I don't know where to start chasing.
View 9 Replies
I have an 05 f350. I cannot get trailer running lights to work. All other lights work. Trailer brakes work, battery charge for dump trailer. I've checked fuses under dash and under hood. Everything checks out. I'm Stumped.
View 6 Replies
I left town tonight and dad called to say I had no tail lights. I stopped and checked the book to see where the fuse is and couldn't find anything for the tail lights or parking lamps. I have brake lights, both rear turn signals and the tail lights blink when you lock it with the fob. The trailer socket shows I have trailer tail/marker working. Why don't my tail lights work?
View 14 Replies
all lights work except parking lights/tail lights. have blue lights under trk had to cut wire by COPS when got dark had no tail light cut wire had shorted taped off changed fuse 15 amp slot 30 10 amp slot 40 still no tail lights. Is their a relay or module before fuse box or after or what could be wrong
View 4 Replies
I'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 Replies
2000 F-250 Super Duty
I was replacing my headlights, which required me to splice in their lights to my parking lights, and I seem to have shutdown ALL my parking lights. I did a test after twisting my wires together and everything worked fine. Then I soldered and heat shrunk them and somewhere during that process I lost all the parking lights.
I checked the 8th fuse as per the manual (for Parking Lamps) with a multimeter and it checked out just fine.
Figured it was the time to ask the experts on here where I should go from here. Are there some other fuses I could be missing, or maybe some else I could do?
Solved: Bad fuse in the #8 slot in the Power Distribution Box (under the hood, near Cab, driver's side)...
View 3 Replies
The flashers and blinkers work, the taillights, brake lights and back up lamps do not.
The truck is a 2004 F250 4x4... Checked all fuses. What am I missing?
View 9 Replies
I'm having issue with my brake lights. Checked for voltage and nothing. Checked the fuses under the dash. Checked the brake pedal switch and have power going out when the pedal is pressed. Is there a relay or something somewhere else? 1999 f250 7.3 superduty....
View 2 Replies
My sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 Replies
I just purchased a '12 f250 Lariat w/ 39k miles. When I got home I noticed one of the three LED running board lights does not work on the passenger side. Can I replace this myself?
View 6 Replies
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
View 9 Replies
How hard is it to install the upfitter switches and the fog lights? Is it all plug and play?
View 4 Replies
Looks like a great option the Job 1 trucks missed out on. Looking into the feasibility of it. This is my first Ford so I am not really sure how the factory plans these things out.
View 14 Replies
