Ford Super Duty (1999-2016) :: 2010 F250 - Trailer Brake Module Fault
Sep 22, 2010
2010 F250 Lariat, cab and a half, PSD. 5600 miles.
Sunday I started the pickup and received "trailer brake module fault" in the message center. I wasn't pulling so wasn't too concerned - hit the reset and continued on.
Sunday night I started the pickup again and received the same message followed by "check brake system". I also lost illuminated gear selection, the traction control active symbol was displayed and the traction control "off" (PB) was illuminated. After several attempts it reset, everything returned to normal and I was able to get home without incident.
Monday morning it wouldn't start. It indicated "trailer brake module fault", "check brake system", traction control active and off, no gear indication, the odometer indicated "-------" and it did not react to the key in the start position.
Tuesday morning I attempted to start and it was the same as the previous attempt. I noticed that the theft prevention appeared active (flashing) so I removed the key, locked the doors, unlocked the doors, tried again - no joy.
I kept trying while holding my mouth in different positions and finally by the grace of God it fired. I delivered it to the dealer.
The dealer called yesterday afternoon and reported that everything is a result of a bad trailer brake module. The new one is to arrive today, they will install and everything will be peachy.
I asked if they could just unplug it and reprogram the truck to believe it never had one - the service writer said it can't be done, different piece parts on trucks with or without trailer brakes.
I really have no choice but to push the "I believe" button and carry on but I am slightly concerned. The fact that the trailer brake module can cause catastrophic failure doesn't seem too cool, I don't have a real warm and fuzzy feeling associated with venturing far from pavement, reliable communication or alternative transportation.
In the meantime I suggest that no one take "trailer brake module failure" lightly.
View 14 Replies
Advertisement
Im getting this almost every time I start it up. It happened once about a month ago, then more often. Now almost every time.
Truck has 1700 mi
I hate to have to bring it to Ford so soon
View 8 Replies
Where I can find a good used or a good deal on a new factory trailer brake controller to fit a 2006 F250 Diesel Truck?
View 1 Replies
I tow a 5th wheel with my 2014 F-250 that has an factory TBC. I just installed Electric over Hydraulic disc brakes on my 5th wheel and was trying to see if there was a setting I needed to change on the TBC to tell it that is now E/H versus E. In the Information section of the dashboard display it talks about the controller actuating electric drum brakes but the manual talks about it being able to do electric AND E/H. What I need to do here...if anything?
View 6 Replies
Every time I touch the brakes I now get a very annoying beep and an error message that says "wiring fault on trailer." I don't have a trailer hooked up so not for sure what's going on. The error message on the console I can live with but that loud beeping is driving me crazy.
If you hit the brake and keep the pedal depressed, then you only get the initial beep and then it goes away. The problem for me is I live north of Dallas so if I'm in traffic then I'm constantly hitting the brakes. I called my dealer today so I'll wait to hear what they have to say.
View 14 Replies
I have a 2008 F450. What may be going on with my truck. In the past the truck would blow the fuse for the door locks. Currently the display is showing wiring fault with no trailer attached, the horn is not working and the cruise control has stopped working. I've covered the basics and checked all relays and fuses and haven't found a faulty one yet. I'm thinking bad ground or possibly bad GEM module???? I've read and read topics and am more confused as to what it could be now than when I started.
View 3 Replies
Brought my truck (2012 F350) for recall service for one of the faulty exhaust temperature sensors. It took them one week to replace the sensor (!), then when I came to pick it up I got: "Trailer Brake Module Fault" message on the display.
I have never seen this message, since I own the truck (I am original owner). The service adviser said it will take a minute to reprogram the module and took the truck back to the shop. Came back after a while, saying that it didn't work and I need to leave the truck, so another technician can work on it tomorrow. Tomorrow came and I got the call that they reprogrammed the module, but the message still shows up, so they need to work on it (another day!).
As of now they still don't know what is going on. Apparently they broke something while replacing the EGT sensor and how to fix it.
View 12 Replies
I'm having some electronic problem with my 350. I parked it and took both batteries out for about a week. I put 2 brand new ones in and hooked them up truck won't start. So I turned key on and left on and the fault that comes up is the "trailer brake module fault" also the abs light, parking brake light & passenger airbag lights are on. Sometimes if I leave key on long enough the lights go away and I can start the truck. But it shuts down during idle. I unplugged the tbc (indash) and the #22 fuse under hood and #31# on passenger side. Still showing the fault. I'm not being allowed to start the truck. I used my tuner and found one code (P0884 tcm power input intermediate)..
View 14 Replies
I've just bought a new 2016 SD xlt. The only extra I wanted that is missing is the factory trailer brake controller. The dealer told me it had to be programmed. I was expecting plug and play and planned to do it myself till they told me that. Is this true?
View 14 Replies
Have recently been getting a "TBC Fault" message and the Beep, as the message goes on and off(annoying) looked around think its the Controler itself,,If I move the slider, and Jiggle it,,the message Blinks on and off as I move the Slider,,,Looking for the method of removing it from the Cubby Hole,,,Gave it a tug,,,and wiggle did not move must have a Clip or Tab to release it.
View 8 Replies
I have a 2005 Ford F-250. I have checked power to the rear harness and all is good except for the tail/running lights.
Is there a fuse for the tail lights? I have checked the manual and don't see one called out. And the relays under the hood are labeled stop lights/turn signals and those are working fine.
I will see if I can trace the brown wire from the rear harness backwards, but it may be a simple fuse.
View 3 Replies
Any info if the "Aux" terminal on the trailer harness wiring on '01 F250s is for reverse lighting? I'd like to put some on my stock trailer. Also, is the "12v" terminal feed switch operated or hot always?
View 2 Replies
I have a 2005 ford f250 with the factory installed brake controller and towing package,until recently all was well,I tow a fairly large travel trailer and last time I hooked the trailer to the truck I noticed the running lights on the trailer were lit, I checked to make sure that I did not have the parking lights turned on or the headlights. I did find posts about the running lights not working and was surprised to find there is a relay somewhere on the central junction fuse block that was integral to the cfb and not user serviceable. Could my problem be that this relay failed in the closed position or am I not going in the right direction in my quest to find this problem. Also looking for a diagram of where this relay is located on the central junction fuse block? I would also consider doing a work around solution rather than having to replace the entire fuse block.
View 7 Replies
Where is the SYNC module in an '11 F250?
View 3 Replies
I have an 08 F450 equipped with Ford integrated trailer brake controller. I tow between 6,000# and 14,000# machinery on a daily basis. I know the gain can be adjusted up to ten. I have noticed while braking "normal" The controller only outputs 1 green bar of power. Manually, the brakes on all my trailers don't grab untill around 3 bars of output. I find myself always sliding the manual lever to relieve the truck. The truck is suffering. I have the gain set to 10 just to get minimal result from the 1 bar output. I know my trailer brakes rock, they can stop the truck and trailer if needed. Can it be adjusted? How many bars are you folks getting with easy braking?
View 6 Replies
I have (2) 2014 f250's both have given the trailer disconnected message randomly from the day they were new. Dealer says everything is with in specification. I just live with it now but something must be wrong with the design. Only does it when no trailer is connected an might be worse when it rains. Might have to hit the ok button every 10 minutes so on bad days.
View 14 Replies
So the other day 2/3/2014 my dad and I went out during the snow storm for the people that needed assistance. That day I pulled a 95' RWD dually with a 4 car open trailer and pushed 4 people from one location. Then after I went to assist the tractor trailer driver. My truck is a 2002 F250 super duty 5.4L with 4:10 gears. I got him unstuck then pulled him a 1/2 mile up a hill.
Pulling a stuck semi out of the snow - YouTube .....
View 6 Replies
My husband and I bought a 09 f-250 with 58000 miles. It used to pull our travel trailer with no power issues. Now the rpms go up & the power goes down. It never gets hot nor any lights come on. It's been in the shop twice. The first time nothing was found. The second time we were told it was dirty fuel filters. The truck only has 70k miles...
View 2 Replies
2009 F250 Super Duty 4X4 auto lock hubs not working. Indicator lights on dash come on but will only go into 4 wheel drive when hubs are locked manually. Vacuum is present at lower of the two vacuum lines when engine is running. I attach the lower line to the module, rotate switch to 4X4 high or low and module doesn't allow vacuum to reach upper nipple. Which fuse operates this module?
View 3 Replies
I have a 2002 F-250 Super Duty 4X4 triton V-10. Where the security control module is located? my keyless remote system does not work even after programming a new remote. The Ford dealership charged me an hour labor to diagnose the problem and they said it's the security control module which I just ordered.
View 14 Replies
I replaced all the exterior bulbs in my 2013 F250 6.7L with LED bulbs. My trailer lights work but brake and signals don't work on the trailer.
View 5 Replies
