Yesterday I punched it and seemed the truck was a bit doggy at higher rpm, the cel blinked but no codes, drove it all day today and it still seemed "not normal" I punched it and it wouldn't go past 3000 rpm and its so doggy it barely moves got a code po141 engine seems like its super lean? This happened on my way home luckily about a mile from my home.
View 2 RepliesJust bought my second SD, this one is a 2002 CC SB 4x4 V10 with 8" lift and 37s. My trouble is that when I fill up the truck when the pump shuts off my gauge only shows 3/4 of a tank. Ignition is off during gas ups.
I have been searching a reading all I can about SD gas gauge issues, but cant find any fixes? Wondering if this problem is sending unit, gauge or pcm? Is the sending unit part of the fuel pump in tank?
Ok so I went mudding this past week, and I put my 997 7.3 truck in 4x4 had fun then took it out of 4 wheel now it won't shift past 2nd gear top speed 35 mph.... It still has all the power revs up Rpms fine but it won't go faster then that.
View 8 Replies2003 7.3 Sd Has a flat spot from 2700 - 3000rpm especially when it changes down, say going up a hill , if I decelerate and let it change back up it will pull again but if I leave it changed down it will not rev anymore. No CEL , put it on the scanner , only code that came up is " intake temp Low " which would not effect it. Have just installed new up pipes , new HPOP hoses , in the past it has had a new IPR and HPOP . It had this flat spot before and it would bring up low boost pres hence the up pipes . Have checked all flanges and intercooler boots etc.
View 2 RepliesI go out of town for work for a week and come back and my 1999 F250 V10 GAS, is acting up. It started when i tried to drive it and it didn't want to shift, it would rev up to 3000+ RPMs and finally shift really hard into gear along with the speed odo not keeping up and bouncing around not wanting to work. I also had my entire gauge cluster lit up with no key and door closed. all the lights were on and it was "dinging" like the door was open and it wasn't. you would hear it when you put your ear up to the door.
So my first thought was to change the VSS (which I did) no luck. So I started wiggling wire loops under the fuse box in the cab and the "dinging" quit.. i took it for a drive and it works like nothing ever happened. Obviously I am guessing there's a short so i brought it to my mechanic and hes saying he couldn't find anything by the fuse box but he thinks its closer or even attached to the gauge cluster itself. could this be true? Why would the gauge cluster loop throw off the shift points?
My 2009 F250 5.4 was throwing code P0442 - minor EVAP control system leak.
The first time it happened, the guy at the parts store checked it out, reset it, and said if it comes back, try replacing the gas cap.
The second time it happened, same thing.
I bought a Stant cap at my local parts shop, and had them reset it again. I don't like the Stant cap since it does not fit the retainer correctly, but it sealed fine.
However, the same code came back.
It took a smoke test to identify a leak from the vent tube on top of the fuel tank. The tube was replaced today.
If the code stays gone for a few hundred miles, I'm going to switch back to the original gas cap. I want to make sure the leak is gone before I change anything.
2002 F-350SD V10 Automatic. Running down the road with no load or with load. First gauges bottom out, next overspeed light starts flashing, engine goes to 3000 RPM on it's own. Stays that way until I shut off then restart. Sometimes it does this several times in one mile.
Second trick, again driving along, all gauges stay up but engine just stops. Got to set dead for 5 minutes before it will start. The shop says on the first problem this happens: Voltage goes way low then goes way high then everything starts failing. We changed battery but no luck. Got to be down line from battery.
What a Brake Code - 4 means for a 1999 Super Duty on the door ID tag?
View 4 RepliesI just purchased a f350 super duty 07 4 dr long bed with the 6.0 liter trying to find the 5 digit code so i can reset key pad on door.
View 2 RepliesReplaced my old sagging leaf springs with new X code springs. Had an almost impossible time centering the axle even with adjustable center link. Even with it totally maxed out it is just barely centered. Now I have a terrible squeak coming from springs. Is this because of the side loading of springs? Is there any fix for it? Not only do they squeak but the drivers side now sags almost an inch even with brand new springs. 2002 F350. Super annoying and irritating
View 1 RepliesI have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 RepliesI just bought an 09 f-250 lariat 6.4 . It has 100k on it. Was driving it AC was working fine. Next time I got in it went to turn the AC Auto on and nothing..the display works fine..lights work..looks like it is working, but nothing. No fan no anything.
Also, the check engine light will come on too. Then next day everything works fine again. Check engine light is out..everything looks perfect. Then this morning the same thing happened..check engine light and no AC.
Code was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 Replies I plan to be buying a 2000 F250 V10 in a couple of hours.
I had my boss run by and take a picture of the door tag so I could determine the axle code. What he sent me was this:
Other than giving me the knowledge of how bad of a photographer he is, it doesn't tell me much else. The axle code area is blank, what gives? Am I just going to have to crawl under the truck when I get there after work?
2004 SD ext cab 5.4L Gas ! I have a mis-fire at low RPMs ! Autozone said it kicked out code P0316 Crank Position Sensor ( CPS ) but the CEL was not on ! So I replaced it and Still has the same problem. I checked the coil packs there good according to the autozone diagram "how to" ! I also pulled each wire 2 check the old shade tree way to see if I could tell that way. Now the CEL is on...
View 14 Replies1999 F250 Super Duty 6.8 V10 4x4 157k miles
On Friday afternoon the ABS light on my dash came up, ran the codes on my SCT Livewire and came up with a "P0500 Vehicle Speed Sensor A"
What should I be going after? Rear speed sensor? Front ABS sensors? Transmission speed sensor?
Speedometer is functioning 90% of the time, twice in the last 48 hours it wouldn't then shift hard and I would pull off to reset.
I have looked over the search results and wondered if there is a way to test the sensor with my multi-meter? Seems quite a bit of people had flashing over-drive light's at the same time, which I do not.
99 F350 7.3l with 4R100 trans. About a month ago I took out a monster trans that had about 60k on it and it was burnt up. No warranty. ..customer bought another monster. After the install when going into 4th the torque converter would instantly lock making it feel as though the truck was falling on its face. Monster had me do some data logging and from the info I provided they determined it had a bad solenoid pack. They sent a new one out...when I went to install the new pack I noticed when I dropped the pan that the fluid was iridescent looking...a bolt for the valve body was in the bottom of the pan and lots of material stuck to the magnets....
Needless to say that trans only lasted about 2 weeks after putting the solenoid pack in. Fast forward to today..got trans number 3 from monster under warranty. After the install everything seemed good. About 30 mins into highway driving the od light starts flashing. ..subsequently the P0741 code. I did put 2 new wire pigtails on the front and rear speed sensors. The pigtails were a ford service part but they were a bit different in design. I am pretty sure the wires are correctly oriented..if not would this cause the issue. I really am leaning towards a bad solenoid pack again. My buddy thinks the TC isn't seated properly....where do I start? Also has an edge programmer on it..but it's been on the same map all this time
My truck threw a check engine yesterday, P1151 and P1152. What could be the problem? 04 f350 with 5.4 with 142,xxx on her
View 14 RepliesI just ordered '00 F250 SC 4x4 SWB XLT with the factory standard manual hubs. The hubs show up on the vehicle order confirmation as code "21M MAN LOCKING HUB". I can't find this code in the ordering guides anywhere but kbb.com shows this code as "Manual hubs delete. Required with 213 shift-on-the-fly". I want the manual hubs. I think ##### is incorrect. For my piece of mind, could someone who has also ordered the factory standard manual hubs verify that the code is indeed 21M. And for those who ordered shift-on-the-fly, could you verify that 21M does NOT show up on your order confirmation...
View 8 RepliesOk says injector pressure sensor low first guess was the upgrade to the blue spring. Did that code clear for a day then comes back on looking at the hfcm but kinda unsure? Came on after we got the real cold snap and i had to buy a block heater I don't see one on here i also added diesel 911 to the tank this is a 05 f250 w 6.0l....
View 2 RepliesSo I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.