Ford Super Duty (1999-2016) :: 2009 F250 - Pulls Right When Brakes Applied?
May 21, 2015
I have a pedal pulsation, steering wheel shimmy, and pull to the right when the brakes are applied in my truck. It is a 2009 F250 4x4 gas V8. I just replaced the pads, rotors, and calipers on the front and that's when the problem started. It definitely gets worse with speed too. I replaced the calipers because the right one had seized up and the left one looked to be on the way. There are no odd noises and the wheel bearing doesn't feel like there is any play in it. What this could be?
View 1 Replies
Advertisement
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
View 10 Replies
My 2003 F250 6.0 pulls to the right when driving at any speed. In order to keep it going straight the steering wheel must be slightly tilted to the left, not much but a little. When the brakes are applied hard it will go to the left slightly if you are not holding the wheel good. Neither of these are terrible, just a nuisance. I'm worried about uneven tire wear too. One front wheel bearing was replaced a few weeks ago. It had this problem before that and still does after. Does this sound like an alignment or maybe something more?
View 13 Replies
Well just called it quits from working on the truck tonight. Had some issues with my brakes going to the floor and pulling to the right some, so I went to auto zone and bought all new pads. Didn't think it was time yet because I just replaced the rotors, pads, calipers, maybe 20,000 miles ago. When I got home and everything pulled apart I looked at the pads on the truck and they still had 60% life. I looked closely and noticed that the guider pins on the caliper bracket (front drivers side) were seized. I figured this is what was causing my truck to pull. Looked on the passenger side and it looked similar. Went back to auto zone and returned the pads and bought new brackets for both sides. I got the drivers side replaced and working and all seemed well. I got to the passenger and had a hell of a time getting the pistons on the caliper to compress so I could get it off. Once I finally got it, I noticed the pins on that side were not seized. I bought 2 sets of guider pins so I took the old ones out and greased up the new ones and installed them. Put everything back together and took the truck for a drive. Everything seemed normal at first, but once I got on the highway and hit the brakes, my truck pulled to the left. HARD.. Im assuming this is because of the pistons on the passenger side caliper I was having a problem with, not having the piston compress all the way causing my truck to pull. While I was looking at the caliper, I also noticed what '"looked" like a grease fitting, and also a bleeder valve a few inches away from it. Am I crazy, or is that fitting for bleeding the brake lines also...?
View 5 Replies
My 2012 f350 6 lift when I push the brakes it pulls to the left kinda bad and the steering wheel is off to the right..
View 4 Replies
Buddy has a problem on his '03 F-450 cab and chassis. When he turns on a turn signal, everything is OK...but it goes out when he applies the brakes. Also, the brake failure light is lit up on the dash, despite the brakes being fine. These problems happened at the same time. I'm think a ground, but not sure where to look.
View 5 Replies
When you turn the headlight switch to the headlight on position, you can pull it out exhibiting a positive click as if it is an additional switch for maybe optional fog lights. If the headlight switch is in the off or running lights only position, this will not pull out. I reviewed the elect. diagram but it does not show and addition circuit for the pull switch functionality?
View 4 Replies
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
View 5 Replies
I have a '03 F350 that I can't seem to solve the brakes vibrating when applied. Replaced front rotors a couple weeks ago. I still have a vibration when I apply the brakes. What am I missing? I didn't replace the back rotors, but maybe I should have. On the passenger front, the inside pad was almost gone and the outside pad was in good shape. I greased the pins before I replaced the pads the last time, but the inside still wore much faster. I also blew out the rear brake line last week and spent Saturday bending a new line and replacing that so the brakes were bled when I had to replace that. I don't feel the pulsing in the pedal, but the truck shakes pretty good when I hit the brakes. What else should I be checking if the rotors are new and the pads are new and the pins have been lubed and the brakes have been bled?
View 6 Replies
I have a 1999 f250 super duty, that was wrecked a few months ago. I have put the truck back together with the mechanic. The front drivers side was wrecked. The power steering fluid tank was cracked and had to be replaced. Also had problems with a box behind the drivers headlight? I did hard wire it together and it fixed the problems I was having the the speedometer and the transmission not shifting correctly. Everything is put back together now but I drove it today and the brakes locked down after driving it a few miles?
Had to push the truck hard to get it back to my house, a mile or so. If I let off the gas it would come to a quick stop. It is ALL four brakes locking up. If it sits for awhile they unlock but will lock up again after driving. The truck is lifted and the ABS light has come on. It was not on before but i am pretty sure the ABS is disabled on the truck. The wires are hanging down by each tire. This is how they truck was when i bought it. Not sure what is causing the brakes to lock up.
View 5 Replies
So a few week back I noticed my brakes were getting soft. Soft meaning that when braking for any distance, I would hear a kind of "pressure release, squeaking" sound coming from the pedal, and the pedal would sometimes go to the floor and the ABS would kick in. Let me tell ya, its a pretty crappy feeling when your brakes aren't doing what their supposed to! So, I replaced the pads all the way around, replaced the master cylinder (bench primed). I took it out for a drive, and it did the same thing. So thinking maybe the fluid is bad, I flushed new fluid through the lines. Took it for a drive, and it felt good right away, the pedal firmed up a bit, and then it did did it again.
Just so I give as much info as possible, the rotors are looking pretty rough and going to be replaced soon.
So, my question[s] are; What is the next step in identifying the problem? Is there a chance the new master cylinder is bad? Could worn rotors cause the caliper to max out and not apply enough pressure? Even though the calipers seemed fine while replacing the pads, could one or more be bad? If so, how do I know?
View 14 Replies
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 Replies
I believe my brakes have a problem.
Lately, I can stomp on my brakes @ 50 mph and they won't trigger the abs or come close to skidding the tires. The peddle goes to the floor if I push hard enough and the truck doesn't seem to stop fast like it used to.
I'm wondering if there is an issue I should be focusing on, like swelling brake lines or some issue you may know of. I'll try bleeding the brakes this coming weekend, but i think its going to be a bad brake line or something.
View 8 Replies
I have a 1992 F250 7.3 diesel 4x4 My brakes wont hold pressure I replaced master cylinder and calipers had the system pressure bled. I don't have any fluid lose and vacuum is good. Can the proportioning valve let fluid bypass, or the rear anti-lock braking system valve let fluid to bypass.
View 14 Replies
2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 Replies
2004 F250, I am getting this howling noise when applying the brakes. It sounds like it is from the left front and is more prevalent when applying the brakes down an incline (off ramp, etc) I pulled the wheels off and the pads were probably 50-60% worn. I bought some new pads and installed them and I still get the same noise. I didn't buy the cheap pads, nor the most expensive either. Either way, I can't figure it out. Would I need new rotors? I would think I would have some vibration if the rotors were warped. My other thought was the caliper, but when I replaced the pads it compressed fine and I lubed the slide rails. Not sure what to do at this point. The truck has 94,000 miles on it, FX4, Lariat, Crew Cab, and it has the 5.4L in it.
View 2 Replies
Took truck out for a ride and stopped for gas. I smelled Brakes and upon inspection found the left rear brake pads were not releasing. Any take on what could be holding it? 2008 F-250.
View 10 Replies
I've replaced the brakes that weren't in that bad of shape anyways and even replaced one of the rotors as it was under federal regulations. I've even put the brake squeak goop on the back of the pads and it keeps squeaking and squeaking and it's driving me insane. Am i missing something here? I don't here any other super duty's squeaking on the road.
View 1 Replies
I just bought an 09 f-250 lariat 6.4 . It has 100k on it. Was driving it AC was working fine. Next time I got in it went to turn the AC Auto on and nothing..the display works fine..lights work..looks like it is working, but nothing. No fan no anything.
Also, the check engine light will come on too. Then next day everything works fine again. Check engine light is out..everything looks perfect. Then this morning the same thing happened..check engine light and no AC.
View 4 Replies
2011 Ford Taurus with 4000 miles. Car, at times, will pull to one side when brakes applied. Dealer could find nothing wrong first time(no cost). Second time they found that the "rear pads stuck in brackets on both sides. removed calipers brackets and pads and did full clean and reassembled". Third time road test found "no pull". "checked on ramp, all brakes seem fine, all free and moving properly. No problem found.". Road test with technician found slight vibration in steering wheel when braking but no pull. Technician says an uneven or slanting street could cause car to pull. Never heard of this before (my other car is fine on the same roads & streets). Is this a possibility as a cause of my problem?
View 17 Replies
On the surface, the F-250/350 seems to have great brakes: big rotors, vented front and rear, and dual-piston calipers front and rear. But, I have two problems:
One is the annoying 'grunt' the brakes make every time you change from Park to Drive, or Park to Reverse, or Drive to Reverse. Its as if under normal brake pressure, the brakes cannot hold the truck from moving against the torque convertor engaging. It's not just my truck, I've heard older SD's with the 5.4L or diesel do this too. If you push the pedal really hard, it won't grunt.
The second problem I think is the root of the first: mushy brakes. Maybe I'm just used to driving european cars with firm brakes, but every time I apply my truck's brakes, it feels like I need to bleed the system! The truck does slow pretty well, and I realize it's heavy, but how can the pedal feel be improved? Maybe replacing the rubber sections with braided stainless?
Lastly, the truck has a 'hill-hold' feature which is retarded in an automatic transmission. My problem with it, is that sometimes it sticks on...engage drive, the truck won't move...a second later its like something gets unstuck and the truck kind of lurches forward.
View 12 Replies
