Ford Super Duty (1999-2016) :: 2008 - Front DS Wheel Binding When Turning And Loose Seals?
Jan 30, 2017
I have a 2008 F-450 Lariat 6.4 4x4. I recently started noticing the front driver side wheel (best I can tell) wheel makes a noise as though it's binding uo when turning either direction, and I can feel it as well. 4wd is not activated and the hubs are in auto. When the front end is off the ground, I rotated the wheels and they spun independently unless the hubs were locked. I noticed what appear to be seals on both the driver and passenger side hanging loose (see pics). What this might be? I recently used the 4wd when we visited White Sands National Monument while pulling a 5th wheel RV.
View 9 Replies
Advertisement
I have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 Replies
Starting about a year ago, "sometimes" when I step on the brakes and am turning the steering wheel, I loose the power steering. I took it to Ford and they said that this is a a known issue but they didn't say what it would take to fix it. Because this problem is intermittent it is very hard to get this fixed unless the mechanic can experience and verify the problem for himself...
View 14 Replies
I have a '99 F250 w/ PSD with 165k miles.
When I drive, I move the steering wheel and nothing happens for the first few degrees of turn and then I encounter resistence and it turns. It's the same either way. The vehicle seems to track nicely, doesn't pull to either side, just a lot of slop in the steering wheel.
Is there a way to determine if this is really steering related or is it just loose/worn front end suspension parts making themselves known? My guess is suspension items, but the fact the front end behaves itself when the truck is moving has me doubting that just a bit.
View 5 Replies
I bought a 2004 F250 Crew Cab LB 4x4 with the 5.4 Motor and when I turn left it has some Tight Spots and I can't figure out why, I checked the Drive axles to make sure the locking hubs were unlocked and they spun freely, I Also have a lot of play in the steering wheel, Could this all be Related to the Steering Box? What else should I check for ?
View 3 Replies
My 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 Replies
1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
View 11 Replies
I'm in the process of changing oil seals on my dually front end. Do I need to worry about backlash settings? I see the gears are attached with solid brackets, which I assume, as just torque to spec and not worry about backlash. What is the torque spec for the four bolts holding the gears/yoke in place?
View 2 Replies
I have some big time slop in my steering wheel, and what started as a type of binding when turning sometimes, is now really sloppy - almost dangerous
Is this the intermediate steering shaft? I just want to be 100% sure that I get the right thing before I buy it, as it's a dealer only part.
View 2 Replies
I have a 03 super duty 3/4 with 45000 miles. I have squeaking sound coming from the front end. My local ford dealer says ford has been replacing those front axle seals but the noise comes back.They said the fix is to keep a dab of grease on them of which I.m doing.That does take care of it for awhile but the squeaking does come back until I put a dab of grease back on them.
View 14 Replies
I replaced the steering gear box in my 06 F250 CCLB 6.8 over the weekend with a reman Cardone. The old gear box had what I can best describe as a chatter/binding if you rocked the wheel back and forth, that's gone now. I sucked out as much fluid as I could, then filled the reservoir several times while the fluid ran out, what came out was very cloudy and gritty, guessing the old box was chewing itself up.
Can't seem to find a straight answer - what fluid SHOULD this have in it?
Sounds like I should have used Mercon, looks like I grabbed Type F instead. Could that cause the steering effort to be extremely light? I mean like ridiculously light, tip of your pinkie barely touching and turning the wheel light?
View 5 Replies
This is the first winter I'm driving my truck. I put it in in 4x4 HIGH the other night due to the snow (and I wanted to check out everything).
Seemed to work fine until I was backing into a parking spot doing a full lock turn. It didn't seem to move. I gave it a little more throttle and it "released" like it was stuck or going over an obstacle. Happened again when I did a full turn backing into my driveway (this time turning the opposite way).
It seems to work fine going forward with tight turns. Also and it doesn't "bind" in 4x2 mode. I haven't tried 4x4 LOW yet ... I guess I don't want to wreck anything if it's not operating properly. Is this normal?
View 10 Replies
2002 F250, 8 inch lift w/ 37's ... Manual locking hubs ...
Ok so my truck has no issues in 2wd even with hubs both locked or when in 4x4 hi/ low with hubs UNLOCKED.
BUT as soon has 4x4 system is in action as I idle forward there's a massive clunking and binding sound like a sledge hammer bouncing off my front diff./ drive shaft. But there's no physical binding of any components that I can see! Just a rhythmic and consistent thumping.
When you turn the wheel either direction the sound intensifies. I even dangled from the side steps as my buddy rolled forward to observe the situation.
View 5 Replies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 Replies
I have a 2008 f-250 6.4 Diesel. Yesterday the Brake Fluid light came on. I thought maybe a sensor, but once I parked and checked I realized my brake fluid was down to the Min line. I started looking for a leak and it was apparent that it was the front drivers wheel area.
I am attaching a picture of the brake. The leak is either coming from the area where the fluid line runs into the gold thing (caliper?) or the bolt at the bottom of the gold thing.
View 1 Replies
My 2010 6.4 F250 seems has a loose steering wheel. The steering of the truck hasn't changed nor has there been uneven wear on the tires. It doesn't drift if I let the steering wheel go. Had the front end inspected and was told it's all good under there.
YET, my actual steering wheel is loose. I can grab the wheel and wiggle it front to back and side to side. It FEELS like the bolts that hold the steering wheel to the column are loose. What was the cause/repair? Is this something I can repair myself or a local shop? Or is this a dealer fix?
View 2 Replies
I have a F250 SD with a 6.0 diesel. My steering wheel is loose. I tested and know for sure is not a problem inside the cabin. Fallow the line thru the linkage to the steering box by the left front wheel. I found an adjustable switch there. Just on top of the steering box. It has a lock nut that must be loosen to adjust what it looks like a hex. Very hard to reach. I have watch some Youtube videos but on different vehicles.
View 1 Replies
I've got a 2008 Ford F250 Superduty Crew Cab. My problem is that the center console of the front bench seat is loose. I keep it folded down nearly all the time and any pressure on the front left corner causes the rear right corner to pivot up.
View 3 Replies
While I was trying to park, I heard a clunk, wheels stayed in the same position. The steering wheel is loose as hell, it literally feels like its buttered up and wont turn the wheels at all, what to buy to fix it? I am thinking I just need a new gearbox....
View 6 Replies
Got my new truck last week and the steering is awful. Loose as a goose. Every bump that you hit jerks the steering wheel around. I changed the tires from the factory 80psi down to 60 for the front and 65 for the rear, didn't work much. On some big bumps it acts like I am losing control. It reminds me of the death wobble on my old 05 F250 which was 4wd. I thought that the 2wd independent suspension would be smoother.
It's got a sway bar up front can I add a steering stabilizer? If so who makes one? Everything else about the truck is great. The new 6.7 is quiet as a mouse and powerful. So far fuel economy is the same as my ecoboost. Haven't got to tow with it yet.
View 5 Replies
My 2002 F250 is knocking loose the front end assembly--the gasket is worn out. So I was shopping around and was considering a beefed-up front end assembly.
View 3 Replies
