I have a 08 F650 with the Cummings engine. I have almost 13 volts but the engine will not crank. When I turn the key the starter don't even click.
View 3 RepliesI have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 RepliesThis is a 6.4L powerstroke, but this is not an engine specific problem. I have a no crank condition that appeared overnight while parked in the driveway. I CAN start it by using the solenoid connector wire near the air filter box and supplying 12v from + battery post. I THINK that eliminates batteries, solenoid and starter.
Now that leaves Trans range sensor or (NSS) and the ignition switch. I can test and get 12V (light) on the Blu/Wh wire from ign sw when turned to start, so that seems good. And as far as I can tell the trans range sensor is internal to the tranny, and I really don't want to go there if possible....
Also there are no codes on the Solus scanner I borrowed. And the voltage is showing as 11.7 on the scanner....is that low enough to prevent voltage from being sent to the solenoid thru the SJB and/or PCM even though engine will start as described?
I have an issue with my 2008 f250 6.4 where the gauge cluster is dark and truck won't crank. The only light on the dash is the airbag light. I have tried reprogamming with my Spartan tuner, checked fuses, removed aftermarket alarm, charged batteries. I scanned and got two codes. P1260 theft detected and a u code no comm with cluster.
View 7 RepliesJust bought a 02 f-250 7.3 with 115k miles. A couple days after I bought it I noticed a lot of white smoke on cold starts for about 20-30 sec at 50 degree temperature. So I tested the GPR which ended up being bad a replaced with the one that is double in size(name escapes me atm) and also did the 50 cent mod to keep the through-valve cover harness from losing connection since both sides were lose.
After that the temp warmed back up and it would only blow a "puff" of white smoke. The past two days it has gotten down to 30-32 and the truck has a rough time starting. Cranks fine but it's almost like it's getting choked or flooded then it will blow smoke for 3-4 minutes after it starts. The truck does have a FASS fuel system on it with stock injectors. Should I try to Ohm out the glow plugs again or where should I start trouble shooting?
I have a 2008 F-350. The Anti-theft light blinks rapidly and the truck will not turn over. Give it some time or take the key out of the ignition and in repeatedly and it will start. Sometimes not till the next day. I have replaced the transceiver & key. Did not fix the problem. Dealers all say: they have never seen this before. I would like to just bypass the Anti-theft system if possible. There are times I will just let it run for hours not to be stuck.
View 4 RepliesSuspect I have a bad fuel pump. I checked for power thru the Inertia Switch. When I first energize the ignition I receive 12v after a couple seconds it drops to 7v. Is this normal? I checked at the connector to pump module and see the same reading. I swapped fuel pump relay and same readings. Just want to makew sure I dont have some other issue before doing pump.
View 2 RepliesMy father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
Just picked up a 2001 Gas F250 4X4 XLT. Everything seems to work except for the electric windows and ABS. I pulled both window switches and cannot find any voltage on the Blue/black cables. I jumped 12v to the drivers side switch and the windows work up and down even in auto. I have voltage at the 30a circuit breaker in the PDB but nothing at fuse #7 in the PCFP. I've checked for voltage at another connector with a Blue/black cable and found nothing. I'm thinking bad cable or GEM. I have noticed that the bell system doesn't sound when you have the key in the off position with the door open if that matters.
View 14 RepliesTruck would have a miss that went away when warmed up past 180. Ficm voltage was low so I got a new one from diesel tech ron. After I installed it The truck would crank for maybe 5-6 turns then lock up and kick the starter out. The starter broke away from the motor from the kickback. I got a new starter in and set up my scangauge 2. In the few turns of the motor i can do before it kicks out, ficm is at 48.5 koeo and cranking, ipr at 14.4, and the icp shoots up to 1100. The ficm sync wont come on and I m stumped what to do next. Dont want to start throwing new sensors at it. 2004 f250 6.0 ...
View 1 RepliesI have 99 f350 single rear wheels 4x4 . I went to start it this morning and it would crank but not start b/c it was cold. I plugged it in and still wouldn't start then it wouldn't even crank. I checked all fuses swapped relays and I have new batteries. The last thing I did was hit on the starter a few times and it started. So I went and bought a new not remand a new starter and put it on and now it won't crank!? I get 12v at the little wire on the selenoid on the fender. So now what?
View 4 RepliesI'm waiting on Christmas shopping to be over to replace the ICP and IPR on my '01 F250. In the mean time I have been going out every few days to crank it and let it run up to temp. Now, however, my batteries have slowly been getting drained over the past month, to where it finally wouldn't crank yesterday. So I'm wondering if I now have a drain somewhere, or is running it at idle for about 20 mins just not sufficient.
View 11 RepliesI work for the transportation department at a school and we have a bunch of 6.0 f350/450 busses and this bus I am working on has a no crank condition. Bus in question is a 2006 F450 6.0.
Currently if you turn the key to start the engine the solenoid just clicks but the engine wont crank. The person working on it before me assumed that the batteries and or starter were bad so they were replaced(0 miles on them right now) but the problem still persists.
First thing I did when I started working on this bus was jumping the starter relay and the starter engages and starts the engine perfectly. That being said I know the starter wiring is fine.
Secondly I looked through the wiring diagrams and saw that the PCM grounds the 85 terminal on the starter relay so I tried grounding the 85 and I was able to crank the engine with the key so that was telling me that the actual starter relay is fine. Next I went and swapped the PCM with another 2006 f450 thinking maybe the grounding switch in the PCM was bad and I have the same no crank condition. The PCM from the bus in question was swapped to the doner bus and it cranked perfectly(PCM in question is fine).
Next thing I did was look up all of the ground locations for the PCM or anything to do with the starter and they were all cleaned and still have the same no crank.
Looking around on the internet I see that the viscous fan can cause a problem if it shorts out so I unplugged that and no change in the no crank. I also saw that the trans range sensor could cause a no crank condition but I am getting back up lights/beeper and the bus "wants" to crank so I am thinking that the TRS is not the problem.
Lastly I tried hooking my Modis scanner up to this bus and was NOT able to communicate with either of the PCM's I tried. Not sure if this is related to my no crank condition. I checked all of the wiring that I could but could not find any chafing or breaks in any of the OBDII wiring. My planned next step is to replace the TRS...
So I have a 2003 6.0L Powerstroke 1 ton. I just replaced the starter thinking the solenoid was the problem. But my luck it wasn't. I turn the key and the ding stops and it's quiet. Dash lights go off. I have the engine light and water in fuel light on. ABS is on I think aswell. I've run out of options.
View 1 RepliesI have a 1999 f350 7.3. Turn the key lights and fuel pump come on but the starter wont crank. I replaced the starter and checked all the fuses i could find. The only way i can get the truck to crank is by jumping the relay under the hood .
View 5 RepliesI replaced the icp in a 2007 ford 6.0 and now it will not crank. I can unplug the icp and it will start, I can also put the old icp in andit will start. The connection has no oil on it and it seems to fit tight too. Is there any thing else I need to try?
View 6 RepliesLast night my truck wouldnt start. Drove fine all day, started up bunch of different times. Went to go home at night. No crank, everything else works, hear the fuel pump prime windows radio everything. smacked the starter a few times but no change. Checked the fuses and relays, all appear good. So im guessing the starter or the starter solenoid, but I cant find one on the truck just something that looks like it could be it attached to the starter.
View 9 Replies2001, F250, Lariat, Super Duty, 7.3 engine with towing package.
It ran seemingly perfect when I parked it and it sat for maybe 10 days to 2 weeks and wouldn't crank. Battery is fine and fully charged. Glow plug heaters work OK. Engine spins really fast, almost like it had no compression. (Not sure though) Temperature in the 30's -50's. I did some research on line and decided to change the Cam Positioning Sensor (CPS). Didn't work, still won't crank. I originally tried my Cheap Harbor Freight OBDII . (Don't waste your money, IMO). What should I troubleshoot next/ or try.
Ok I have a 99 f250sd v10 with 180k miles. Original owner and have most work my self over the years. Son took the truck to fill it up, started fine ,filled it up and now will not start. It has power but will not crank. Tries to but no good. I was thinking battery died. New battery same results. Sort of tried to start but not turning over. With the new battery i tried several times then nothing. No power at all. No lights, nothing. So I put the old battery back in and still no power at all. I'm thinking the starter is toast and my repeated attempts to start that I pulled too many amps and blew a master fuse? It stilling in a parking lot until tonight when I can tow it home. Where to start.
View 9 RepliesYesterday I was on a pretty long trip and stopped off the interstate to grab some food. My truck is really loud so I always shut my engine off at the drive-thru. When I went to crack it back up everything lit up but when I turned the key nothing happened. I had the truck towed home and I put a new starter on it. Still nothing.....
Well after further investigating where the positive wire that comes from the starter to the battery was broken at the battery post. Don't know how the heck that happened but I fixed it back to factory condition but still nothing. I'm at a complete loss. I checked all fuses and everything looks good.
When I turn the key everything lights up, then turn to crank it and nothing but a slight sound coming from those square silver things in the fuse panel under the steering wheel.
2007 f250 PSD with to many extras to list
I've been having sporadic starting issues with my truck since the fall. I had the spark plugs changed but that did not work. The hard starts usually occur when the engine is hot....after filling gas or just running into the grocery store. The engine seems to turn over slowly the first try and won't start. The second or third try the engine turns over normally and the truck usually starts.
I just got back from a 90 minute drive and shut off the truck for 5 minutes and now it won't even turn over. My thought is that it can't be the battery....its been charging for 90 minutes. Headlights are strong, wipers work fast, fan blows hard. That being said I think alternator or battery can be ruled out?
Where do I look next? Starter? Is there a starter solenoid that could be defective?