I started my truck this morning, keep in mind it's -28 outside, and after starting it I switched to defrost....I heard a snap-pop and what sounded like something falling in the heater box? I tested all the blend door positions and they seem to work.....noise normal or not? Never heard it before today......
View 1 RepliesI tried to take my tailgate off my 08 F-450 today.
Did it the same as every tailgate Ive taken off in the last 20 years...........it wouldn't come.
Is there a trick to it?
How do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 RepliesHave a 2008 F-450 that I just got and the trailer light outlet does not work. There is constant power to one pin and nothing on the tail/turn/stop pins. I have checked all of the fuses and relays and they seem to been fine. And yes, I did a search and did not come up with anything.
View 6 RepliesOur F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesI got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 RepliesI've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
I thought there was a v10 specific superduty section like how the psd does, but my thread went in the "performance, engine, troubleshooting" section.
I wanted more exposure than that particular small viewed area.
I don't have a video of the noise, but my 99 f450 v10 5spd has some iffy noise coming from the front. I've read so many threads on this and they either end with "my motor had 1-2-3 bad pistons" or "my flexplate was cracked" and all that dealt with chain tensioners were never finished.
I know what piston slap sounds like (worked on many cobras and lightnings with forged pistons that had it) and have experience with bad wrist pins and broken piston skirts, and this noise doesn't sound like any of it.
Noise is a loud clicking/clunking/Detroit diesel idle noise. When you rev the engine up it doesn't lighten or get better, only worse as rpm goes up. Oil is terrible looking, I'll be getting that changed this week.
Story on truck. I've had this thing for 4 years with blown motor. I got a buddy that acquired a parts truck and he said it ran good. I dropped my truck off and he swapped the engine. I got my truck back running, but with this engine noise. He said it needs to get run some more and change oil.
I think it's timing tensioners, my buddy says it will come out of it, a mechanic friend says it's going to blow up "because they all do" and I don't really want to replace the engine again.
If it's tensioners, how big of a job is it. I have the cam clamps and crank stop and the ford tools to make sure crank and cams don't rotate while apart.
I'm just 650 miles from my truck and may need someone else to do the work. Which sucks.
I did my ball joints, and the drivers side oem manual locking hub was a bear to wiggle out but eventually came. When I put it back in after I finished, the wire retaining ring clicked into place but wasn't seated as far in as the passenger side (I could still see the wire). Didn't think much of it. Drove off. 30 miles later I heard a pop and saw the hub rolling down the road behind me.
Stopped and picked it up, went home managed to find a pair of locking rings i kept off my Dana 50, and I just cannot get it to go far enough in for the snap ring to fully seat in the groove. I tried tapping the axle further in, I tried tapping on the steel part of the hub with a deadblow, but it feels like it's in as far as it will go. Not sure what to do, driving without a locking hub right now.
Started to attempt to replace the heater core in my 08 SD 6.4. Didn't know the entire plenum has to come out in order to replace it. How to remove the plenum? My buddy is a Ford tech but I just am not getting what he is telling me and there is next to nothing coming up when I try to search.
View 2 RepliesI broke 2 snap ring plier on this thing, what is the make and model of snap ring pliers used to remove the snap ring off axle in hub ? I have some others but too beefy won't move in there. They need to be long but strong. I've heard Snap On Item: SRPC9000A works but I don't know of any Snap On guys around here and I need to get this thing done.
View 10 RepliesI have a 1999 F450 that was bought new as a cab and chassis. The truck belonged to my dad who passed away two years ago and now I have it. I am wondering if it has 4.30 or 4.88 gears. The rear end is huge! It has an aluminum cover with cooling fins on it, not sure if they both had that or not. I looked online and I think it said all cab and chassis had 4.88?
View 10 RepliesMy 99 f450 7.3 runs bad on first start of day. I checked the codes 3 codes p0475, p0470 and p1247. Now here is what I tried I plugged it in over night and it will start and run as should the next morning with out side temp 47. Drove the truck late yesterday evening didn't plug up tried it this morning with a outside temp of 47 truck starts but missing and like of power. My problem seems to be temp related. Will low boost pressure cause this problem what do I need to do?
View 4 RepliesPurchased new 2016 450 platinum. Has less than 800 miles on it and has a terrible vibration between 70-80 mph... Already have taken to dealer who stated there was a wheel out of balance and that they fixed the issue. But still present.
View 14 RepliesI have a 99 F450. I have an ABS light on. No codes (at least not that my code reader can pickup), but I am also not having any issues. Brakes work fine. What to swap out or where to look?
View 7 RepliesCan an f-450 with a blown 6.4 diesel received an transplant from an f-350 V-10.
How much would need to go over from the f-350 to f-450?
I was driving from home to work the other day and it was 6 degrees out. My heat was working good and everything was fine and then all of a sudden the passenger side started blowing cool air. Not cold not warm. Driver side was still hot. It is a lariat and has dual temp zones. Everything I read everyone says blender doors but what would make it stop working out of no where when everything was fine. Occasionally when I start my truck and turn the heat on it makes a popping noise under the dash when the blower kicks on. But it has done this since I owned it an never had an issue. It's 25 below today and I would really love to have completely functional heat. It's an 2008 f350.
View 14 RepliesI have an 02 F450 with a dump bed an just under 45,000 miles (was barley used by the first owner). This maybe unrelated to my problem but is worth mentioning. This past week I noticed a small puddle where I had previously parked at a customers house so I checked the oil. I was about 2 quarts low. I followed the oil trail up and found a pool in the valley. One of the high pressure lines were loose and the seal was chewed up so I replaced it and tightened it. No more oil leak.
Now my new problem. Two days later, after about 45 minutes on the interstate driving about 75 mph the truck started to rapidly lose power as if it was running out of fuel. I heard a loud ticking sound coming from the engine and the more I tried to accelerate the worse it got. I pulled over and the truck stalled. I thought that maybe my fuel gauge had crapped the bed on me because it still read a little over 1/4 tank. I called a buddy and got more deisal in it and it started right up. We'll after about 5 minutes of 60 mph it started to happen again. So to fast forward... I opened up the tank and found the the strainer had crumbled in the bottom of the tank.
So I cleaned out the screens in the sending unit and replaced the strainer, replaced the fuel filter, and reverse blew out the lines. I read about checking the hpop reservoir for oil and it is present. So to sum up, as long as I stay under 60mph or so I can get about 5 minutes of run time before the truck starts to stutter and stumble. If I shut it off for about 5minutes I can go back up to 60 again but it the cycle continues. 5 on and 5 off. If I start the truck after say 30 seconds after shutting it off it sounds like it's going to die and has no power at all. I have worked on a lot of vehicles but none with anything like this and this is my first deisal. What do I do to get this beast back to normal?
I have a 1999 F450 Diesel dump truck. Automatic. The problem that I have is that the truck will drive VERY SLOWLY while the rps go up.
You can hear the engine revving up, and a strong air sound when doing so (do not know if intake or exhaust, but its like a strong wind sound. And not like a hiss, so I do not think its a vacuum leak).
The transmission goes through gears fine, but it does the rev up thing through every gear. So I am wondering if something like the torque converter might be broken or slipping.
For example, if you go with the loaded truck up a hill, you have to really push it to keep any type of speed. Or when you get off a red light.
When I bought it used, I thought that it might have a really short final gear. But that would not explain the high RPM and no push.....
No codes at all.
It's a 2004 F450 super duty, no power steering. The pump seems to function, no pump whine. I was told that it may be the steering gear box it's self.
View 2 RepliesI've got a 2004 f450 6.0 diesel. This thing will start and run great when it's cold. Then when it gets to operating temp, around 190, it will shut down. This is getting worse and worse.
A little history, it was doing this for awhile and a had a few other issues before this. Puking antifreeze, stiction issues, and bad exhaust manifold. Since it wasn't running great I figured why not pull that cab and take care of these issues.
As of last week she got new head gaskets, new exhaust manifold, new injectors, updated standpipes, updated dummy plugs, new o rings on hpop (yellow on the bottom), and a new pipe to the oil pump. I have the old style it's not the stc fitting.
All that work, it still stalls when warm. I monitor with a scan gauge 2. ( Big diesel tech Ron's fan) ...
First thing, give here two second crank start right up, runs better then ever. Gets to operating temp, rev it up, then stalls. Ipc is at 85% ipr gets up to 180 psi.
Unplug ipc, shows 765 psi on the ipr still no start. Put shop air to her and I can't hear any leaks ( probably 15 mins or so).