Ford Super Duty (1999-2016) :: 2008 F350 Going In Limp Mode Without Engine Light - Code P0088
Feb 24, 2015
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.
View 3 Replies
Advertisement
2008 F350 6.4 ... So I've been reading all about the spartan tuner throwing the P0088 code, and the ford band aid fix, I guess my question is, I'm going to have my HPFP replaced for peace of mind. Truck has 106,000 miles on it. Will i have an issue at the dealer if I show up with my tuner/exhaust on the truck? I'm not worried about warranty obviously, I just want to know are they going to have to unplug the tuner? Or something, I am just concerned how they'll go about putting the new HPFP on.
View 6 Replies
F250 7.3L diesel started to flash OD light, goes into limp mode, code p1747. No other codes. Have had issues for a couple of years where the truck would not shift into gear for awhile; sometimes a couple of minutes till it would engage. Have done lots of diagnostics. Visual check harness. Have 12v on pins 1&12 on harness at transmission plug. Plug had some ATF visible, but cleaned it up and continuity good. (with 4" exhaust hard to get to connector).
Checked all solenoid wires with a DVM back to plug at PCM for continuity and shorts, all good. Pulled transmission pack and checked resistance on all solenoids except temp varistor all within specs. Removed Banks Trans Command and rewired tranny plug and pulled Ottomind chip from PCM. Still goes into limp mode and throws code. Did not see any bad solder joints or burns inside PCM by the way.
Seems like PCM right? But here is a complication to my issues. For over a year I have been having electrical issues like the radio not working and windows not working intermittently after starting up. After running for awhile or on restart would work fine. Sounds like the Instrument Cluster issues or relays.(?)
Will be pulling IC and checking for any bad solder joints. However, did not throw p1747 till just recently and now my radio has really gone wonky. It comes on when key is on automatically and then proceeds to cycle through settings; AM-FM-CD.
So questions are, "Is it possible that a bad Instrument Cluster can cause a p1747 code?" "Bad Ground to Tranny" "Can a bad PCM cause a electrical issue in IC??" "Are these 2 separate issues?"
2002 f250 7.3L, 4R100 automatic trans, ~180,000miles
Banks Stinger package, 4" exhaust, TransCommand, (now removed).
View 2 Replies
Bought a brand new F250 6.7 it has 7000 miles in it now and the check engine light comes on and the truck goes into limp mode. I have taken it in to the dealership twice they said there is no code they can find and they just reset the check engine light and it does ok for a bit then starts the cycle all over again. It also is only getting about 6.5 mpg....
View 6 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
I have a 2015 SRW f350 and has been fairly problem free. Last Thursday I was driving home and I received the reduced engine power and code popped up P0088, high pressure fuel rail issue.. anyway, I just popped over 36k miles, the truck is at 36,278 miles, so I take it in thinking they will goodwill it.
I get a call saying they can't clear the code and the TCM AND PCM can't communicate and they have to reach out to Ford engineering. They find the PCM is corrupt, they call me twice and ask if the truck has been tuned, the answer is no, but then pin me against the wall saying I am the second owner, which I am, and that it could have been tuned prior. I tell them to prove it, you can see if there has been a tune. The truck truly has never been tuned, it was sold at Ford factory auction as a employee vehicle.
Now they are trying to tell me the corruption was due to the tune, which it never had. But they won't goodwill it and say I am responsible for all the diag and work done, I say no. I say this should be a warranty issue and should be covered, they say it was tuned, I told them to prove it.
View 6 Replies
I recently bought a h&s tuner and installed a dpf delete kit. Everything works great when the truck is not plugged in to the tuner although when I do plug it in, the truck keeps throwing a communications code and goes into a limp mode until I delete the code. I believe it was p0073 but i maye be mistaken. Regardless it has to do with communicating through the obd2 port. I sent the tuner in to get checked out and it turns out its something to do with the truck. I've checked all the fuses and tried to check for broken wires. Where to look next?
View 4 Replies
So I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.
View 6 Replies
Ok just bought this truck ran fine. Put a sct tuner on that the truck came with and some how got the egr turned on. It had a egr delete so it was smoking and finally found it out that it had turned on but fixed it. Now we have another problem, it will start up and run fine and about 45 seconds it will start running rough and go into a limp mode. It will run rough and starts to die slowly and when it starts to die there is no throttle at all.
View 4 Replies
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
View 9 Replies
My F250 with V10 has developed an overheating problem. While driving, the temp gauge suddenly shoots to max, and the truck goes into limp mode. Turning off the truck and ignition, waiting a few minutes, and all seems to be well again - sometimes for only a minute, sometimes for several days. No steam leaking, the water in the reservoir seems to be normal temperature, the radiator is not overly hot, and the AC keeps on blowing ice cold. Me thinks it is not really overheating, it just thinks it is. So where to start? Change the temp sensor first, or the thermostat? It seems the hoses are fairly firm, I don't believe they are collapsing from suction.
View 14 Replies
I have looked at many of the other treads and I can not find the answer. How do I locate the keyless entry code sticker in my 2008 F350? I just bought the truck used, I do not have the card that is delivered with the truck and I don't want to pay the Stealership to hook it up to there computer. I am looking for the RAP or the computer module as it is called in the owner's guide.
It is not behind the glove box, there is no longer a fuse access panel under the dash like the earlier SD's, the drink holder under the upfitter switches does not "pop out." Before I start with any tools, I am looking for input.
View 14 Replies
I have a 08 F350 CC with the factory fog lights. One of them has burnt out. Do I replace just the bulb or the entire unit? Is there a part number?
View 1 Replies
My buddy has a 2002 F350 CC Longbed with a 7.3. Last night the overdrive light started blinking. He said he drove it today and it takes about a mile or so for the light to come on but then it is a steady blinking. Truck has about 254K miles on it. He said other than the blinking light everything seems normal. How to figure out what this issue may be?
I got AE hooked up on his rig.
When I pull (ALL) codes this is what I get:
When I pull (Current) codes I get this:
I tried to clear the code and the light stopped blinking, but he said it started blinking again on the way home.
View 2 Replies
I just got an Egde Evo which I installed and everything looked great. After a few runs, I noticed the ABS light coming on an soon after that my transmission goes to limp mode (the wrench lights up).
I receive the DTC error: P2106 on the Edge Evo.
I have gone back to Factory default, but it keeps coming back, ie. the ABS light lights up and the Trans goes to Forced Limited Power (according to the Evo).
View 6 Replies
1999 F350 SD ... Yesterday when goosin it to get on the highway my rig threw up a code quickly and engine temp started to increase. Once temp got in the red, oil pressure got a little figgity. The code was for the ICP(p1212), so I cleaned the plug and made sure coolant and oil were topped. This morning she ran barely over normal temp (stock gauge). This afternoon same thing as yesterday but without the code. When I let off of the accelerator temp goes down. I just got married so I have little funds to throw at a shop.
View 4 Replies
I have an 08 F350 regular cab 4X4 that the cargo light doesn't work, Is this powered from the interior light like the old ones? or does it get its power from the GEM module? If it comes from the GEM is it possible to feed it like the old ones from the interior dome light without killing something? I really miss having a cargo light.
View 3 Replies
2011 F350 loaded. Stuck on vent mode. Found actuator can feel it trying to move but something is stuck. Tried to remove the actuator but not enough room between the motor and a steel bracket welded in to the dash. (Not removable). Do I have to remove the dash ? (I suspect something fell inside and is stopping the big vent door from moving as i did pull the motor far enough away to move all the door except the vent door.
View 2 Replies
I'm having a strange issue with my 2008 F350 6.4. I have only had this truck for about 2 months now. Every time it gets wet (from rain or a carwash), the 4x4 low light begins flashing, and the truck surges badly at low speeds. When I get above about 25 MPH, the light stops, and the truck runs normally. At the next stoplight, it happens all over again. After a couple days of dry time (?), the truck is back to normal (until it gets wet again). I have found a couple of old threads involving some similar symptoms, but they were never resolved on this forum (that I could find). I believe the transfer case selector motor has been replaced at some point, as it has a Dorman brand sticker on it. I wouldn't think Ford would use Dorman parts as original equipment.
View 4 Replies
I literally just purchased a "new" 06 F350 and have had it just over a month. I bought it from a used car place in Salt Lake City and have put roughly 250 miles on it, it has 105k on it. While having 1 sled in the bed and towing a 1-place snowmobile trailer up a 8% grade my check engine light lit up. Little back story, there was a slight hiccup that I started to realize it had about a few days after purchasing it, would kind of buck a few times under normal acceleration around to 40-60 mph not every time just occasionally. Been meaning to take it to a friend to have it looked at, just been fairly busy.
Now when I was driving it back home (~8-10 miles, almost exclusively downhill) at stop light and accelerating from 0mph it would not prime the boost, I was getting almost no power until I hit 2000 rpm then all of a sudden things were fine turbo would engage I was able to drive normally. It hasn't moved in 2 days as I will not drive it until I know what is wrong with it. In doing a little research I read about turbo veins being stuck open, ignition problems, and a few other things that might pertain to what is going on with my truck. I have a buddy coming in the morning tomorrow to pull some codes with a scanner so I will have more information here shortly but I just wanted to get the conversation started on this.
View 6 Replies
I have a 2006 350 6.0l check engine light came on today truck is running normal except the fuel gauge and mile to empty gauges keep changing when I turn the truck off. What this could be?
View 1 Replies
