Ford Super Duty (1999-2016) :: 2008 F350 Won't Start After Fuel Filter Change
Dec 8, 2011
2 nights ago changed the fuel filters for the 3rd time on truck since bought it a year ago. It has 67,000 miles. F350 6.4 L 2008. The truck ran for about 2 minutes and then wouldn't start. For the last two nights have done everything including cycling the key over and over to purge air, replacing the fuel filters thinking the first ones may have been defective, pumped the gas pedal while trying to start it, tried to start it with fuel cut off switch held in, changed o rings etc. The first night I didn't get fuel at the head but after changing the filters a second time, I now have fuel at the head. That is the only progress I have made. The truck has gas and it is fine as we are using it in other trucks. The battery has never been allowed to totally deplete.
View 9 Replies
Advertisement
I'm gonna change plugs , hoses, belts and fuel filter on my 08V10. Hoping it works with the mpg.
Anything else I should look for or do? Is there anything I need to know about changing the fuel filter?
View 4 Replies
I had my fuel filters changed at the dealership today on my '15, and then I bought fuel and headed home (70 miles). About half way home I got a "Low Fuel Pressure" message and a little while after that "Reduced Engine Power" along with the check engine light.
I pulled over to see if they did something like leave the drain open, thinking it might be sucking air. Of course it was dark and I could not see anything. However I did hear a buzzing sound and could feel a vibration when I touched the fuel line going into the top of engine filter.
While it is possible I got bad fuel, I suspect they did something wrong installing the filters. Even after cycling the fuel pump multiple times they had a hard time getting it started afterwards; I think they finally disconnected the top fuel line to bleed the air out.
I continued home and made it, but not sure what to do now; its 70 miles back to the dealer.
What is the most likely problem? Improper fuel filter installation or bad fuel?
Should I pull the filters in the morning see if there is something obvious like an out-of-place gasket? If so, top or bottom filter?
Is this a tow truck affair or should I drive 70 miles back to the dealer?
What the heck is the buzzing sound?
View 7 Replies
Here within the next couple weeks, i am wanting to do some routine maintenance. right now on my list is just an oil change along with the fuel filter.
View 6 Replies
2008 f250 auto
is the trans filter change possible?
i didnt see this in the tech folder and no videos for a 2008
View 1 Replies
After replacing fuel filter, pump relay, and air filter for good measure my 2002 f250 v10 gas engine still wont start. What to do?
View 13 Replies
Changing tranny fluid/filter today, all has been going great until I went to take the filter o-ring out that didn't come with the filter. It will not come out! made a hook tool out of an old tooth brush like someone on here did, o-ring wont budge. Tried a hook pick, it wont dudge (actually bent the tip on the pick and started to tear the o-ring). Everything is ready to go back together and get filled, but this stupid o-ring will not come out!
View 3 Replies
OK, I have a 2002 F350 with 160k miles that cranks fine, but has a hard time starting when it is cold. By cold I mean that it is not hot from being driven in the last 5 hrs or so. No problem starting after being at rifle practice for 3 hrs or after a trip to the store. Always have trouble starting in the morning, like this morning when the temperature outside was 49 deg. I have to crank for quite a while to get it to turn over, but once it catches, it runs like a champ. Afraid I'm going to wear my starter or batteries out because It seems like I have to crank for about 2 minutes.
I have a fairly new CPS replaced less than 15k miles ago, new glow plugs, and recently replaced the leaky bleeder valve on the bowl. This difficult starting condition came about some time before the bleeder valve seal repair, and is still doing it after the repair. This problem seems to have cropped up on it's own unrelated to any work I have done. I am using Mobile 1 5W-40 diesel oil. When the no start occurs, there is no smoke present out of the tail pipe like what you would get if you had bad glow plugs. There is just no fuel getting into the injectors.
View 2 Replies
So here's the deal, crank no start its getting fuel. Has base oil pressure and i put a ficm on that test good with a voltage meter key on engine off and cranking. I haven't hand any trouble finding info on this issue so. We can keep picking away. Just cant find anything about this.
A buddy of mine who has been trying to figure it out for me, Got it to start using a starting fluid. And it would run if someone was pushing the gas peddle but wouldn't idle. Or start without the starting fluid.
View 2 Replies
I'm just a shade tree mechanic try to diagnose a hot crank no start condition on my 2006 F-350 6.0 that I purchased second hand about six months ago. I first took it to a diesel shop to have them fix it and the mechanic told me that the stand pipes and dummy plugs needed changing out but couldn't tell me 100% if that would fix the hot no start problem.. I have been reading a lot about this problem and it seems that the snap to connect fitting on the HPOP is the most common problem on these trucks. It seemed easy enough to do so I went after it only to find it was already replaced with the updated part.
I went ahead and changed it anyway but it obviously didn't work. So today I pressurized the system through the ICP port with my small harbor freight compressor up to 80 psi and forced the IPR valve closed with 12v. I then listened for a leak in the passenger side valve cover with a hose stuck in the oil fill cap, the driver side cover from some drain hole under the air filter housing and in the oil filter housing. I could hear a mild hissing from the driver side and the oil filter housing but it was clearly louder from the oil fill on the passenger side. This leads me to believe I have a top seal leak from one of the injectors on the passenger side, but not 100% sure. Should I be hearing anything at all from the driver side and from the oil filter housing if its a bad seal in the passenger side?
Another problem I just found out I have seems like maybe fuel in the oil. I done a oil change this week after 3500 miles since last change and drained out five gallons of oil!! The oil seemed really thin. My coolant level is still good so the only thing I can think of is fuel dilution. Could this possibly be the same o ring or injector that is causing my hpo leak or something else? Will a bubble or balloon test diagnose this?
I bought a cheap OBD2 reader that works on my Ipad with a app called Dashcommand so I can see what codes were stored. The codes are...
P0401- Exhaust Gas Recirculation A Flow Insufficient Detected (EGR has been deleted)
P0528-Fan Speed Sensor Circuit No Signal
P0670-Glow Plug Control Circuit/Open
P0683-Glow Plug Control Module to PCM Communication Circuit
P2290-Injection Control Pressure Too Low
So far my thoughts are to replace the injector and nipple cup seals to take care of the hpo leak. Once I have the valve cover off, clean the injectors real good and cycle the fuel pump with turning the key on and inspect the injectors for a fuel leak. Is there a better way than this?
View 8 Replies
So the first issue is, if the vehicle is cold (regardless of temp outside) it takes forever to start it. It cranks and cranks and cranks and after a couple seconds of cranking I stop, wait a second, then try again. Usually it takes two sometimes three tries to start it. The guy who I bought it off of said it has newer glow plugs (last year I believe) and also I have replaced the batteries. Once its warmed up it does not do this at all.
Secondly and also something that just recently started happening, my water in fuel light keeps kicking in. I drained the water out of the water catcher reservoir under the truck multiple times and the first time water actually came out but every time after that simply diesel fuel comes out. I added a bottle of water remover to the fuel as well and ran it down to a quarter tank. Then filled the truck up completely, added two more bottles of water remover. The light still comes on. I noticed it only comes on when I am going up or down a fill. When I am driving on flat ground it does not kick on.
View 4 Replies
How often in miles (mostly highway and city) would you change the following:
1.Baldwin spin on fuel filter added with hutch mod
2. Napa diy 6637 air filter mod with no sleeve over it, just the paper element
3. Stock fuel bowl filter after having added a pre-filter (previously mentioned in #1)
View 1 Replies
I have an 11 F350 6.7. It has just under 200K miles on it. Yesterday I changed the oil. Very uneventful. Today however, I was driving home, about 100 miles, and my truck's temp spiked. Not like a little spike, but jumped to the 3/4 mark(if there was one) then slowly kept rising to to the overheat mark. I pulled off onto the hard shoulder waited an hour or so to let it cool down, then finished the drive home. All the way home my temp gauge seemed like it was on some sort of drug. It would jump a needle width when I would have to accelerate, then slowly cool to normal after I got up to cruising speed.
When I got home I checked the oil level and it was spot on in the "normal" range. I haven't used a different type/brand/weight of oil in the last 100k miles. Did something just give out on my truck? I had the coolant flushed and replaced at the dealer within the last 10k miles. Up until this point this truck has been exceedingly reliable. I pull a 13k 5th wheel once a month and drive about 40k-ish miles a year.
View 9 Replies
I have a 2014 f 350 super cab xlt. Ford design engineers should be ashamed. But really who has installed the older (2009 ish) ford seat in there trucks for a little more comfort? How much fabrication was needed? Hate to say it but if I cant put the older truck seats in I'm going to buy GMC. These seats really suck.
View 3 Replies
We have been having near zero temps for several days and it occurred to me that there may be some amount of water in the water separator in the rail mounted fuel filter (not enough to send a message, but maybe some amount). I only have 3,000 miles on the truck. So, just wondering if a small amount of water is going to hurt anything in the filter or filter housing if it freezes? Should I drain the filter in freezing weather even though enough water hasn't collected enough to activate a message?
View 6 Replies
Any luck changing the external transmission fluid filter, without breaking it or its piping?
View 2 Replies
I have a 2003 Ford f 250 turbo diesel 7.3lt V/8,is there a tool to undo the cap on the fuel filter as i have problems every time i service the truck.
View 5 Replies
Just picked up new 2014 F350 lariat today and I can't figure out how to change the keypad code. I enter the factory code and hit add, but when I enter a new 5 digit code it wont let me hit enter.
View 2 Replies
Trying to stay up on my maintenance on my '11 f-350 diesel. It just turned 59k. I can only find Ford's recommended service interval for changing the fluid in the transfer case listed in the "Special Operating Conditions" section of my Scheduled Maintenance Guide for towing, delivery, off-road and dusty conditions at 60,000 miles. I tow some, but maybe 20% of the time, I end up driving a lot of stop and go though.
So I found this nice how to online "Guzzle's Transfer Case Fluid Change" - it's for a 02 heavy duty, is it about the same on the newer diesel trucks?
View 1 Replies
2001 f350 7.3 Changed front injector drivers side inspected all 4 glow plugs on this side turned motor over my hand 5 time reinstalled plugs put back together hooked both plugs back up started truck and no of the cylinder on drivers side are firing checked them with temp gun!! what did i not do or do wrong.
View 4 Replies
2001 F350. I need to take the face plate off of my in dash cup holder and put it on the new one that I bought. Ford charges a premium price on the Dark Parchment or Dark Buckskin that I have. So the dealership I bought the new one from told me its possible to change out the face plate.
View 1 Replies
