Ford Super Duty (1999-2016) :: 2008 F350 - Multiple Codes / Cylinder 5 Misfire
Jun 27, 2014
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
View 3 Replies
Advertisement
I have a 2006 F350 SRW 4WD 6.0 with 127000 miles on it. A couple of weeks ago it, pulling out of my driveway, it hesitated and tow haul started flashing. I had codes pulled and it showed P1780, P0751, and P2700. After turning off, codes were gone and tow haul off. Ran fine since then every day. Yesterday while going about 50 mph it started acting like it was in neutral (revving up), nothing happened when mashing the accelerator. Coasted to a driveway and truck would not move, only sounded like it was in neutral.
View 1 Replies
I have a 2001 F 350 with a V10 it keeps coming back as a misfire on cylinder 3 and 4.. I replaced all of the coils and plugs and pigtails I have even swapped out the coil packs from side to side and I still keep coming back with the same code. The truck has a bad check around 1500 RPM with a load on the motor mainly doesn't in overdrive and first starting off...
View 14 Replies
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 Replies
We bought the car used for my youngest daughter and it had a couple of codes in it. 1st was the o2 sensor.. easy fix, grabbed an OEM one and stuck it in. Then there was the Cyl 2/ multiple cyl misfire codes that kept getting thrown.
I've seen a bunch of post about people pretty much doing the same things I started out with and still having a problem.....
1) Swapped around all the coils.. still got a #2 misfire... So, coils are good.
2) Swapped in NGK Platinum plugs with a .032 gap.... still getting misfire.
3) Replaced the crank shaft position sensor...... still misfire
4) Noticed that there was an Ebay injector in the #2 cyl...... when I pulled the plugs, that cyl was running a little lean..... bought an OEM injector to go back in there...... still getting misfire
SO, I tried using a propane torch head and putting out gas around the intake to search for vacuum leak and got no response....... so, for the heck of it, I went old school and grabbed a can of starting fluid and started spraying it on the intake around where it bolts to head... bam... found a vacuum leak on #2 cyl....... ordered an intake gasket off of ebay, spent about 3 hours on it pulling the intake and replacing the gasket,( the bolts had loosened up over time and there were small tears in the gasket allowing it to suck air) .. put the new gasket on, cleared the codes and it's been running perfect ever since.
Check for a vacuum leak where the intake manifold bolts to the head... might save time and money.
View 3 Replies
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
View 3 Replies
I just recently purchased a 2008 ford f350 5.4L gasser, supercab long box. The truck has 167,000km on it. I flew about 700km from my hometown to pick up the truck and drive it home. After driving about 300km I started noticing a few problems.
The engine light codes that have been stored as of now:
P0420 (Catalyst code)
P0420 (Catalyst code)
P0191 (Fuel rail pressure sensor i think?)
The issue I'm having is that the truck has absolutely no power going uphill or accelerating. If I'm climbing a hill and have the gas pedal pushed in at a steady rate its almost as if the transmission wont shift, and if i push harder on the gas the truck begins to shudder. When the truck is cold it runs normal and climbs hills no problem, but once it heats up the problem returns. Another odd thing I noticed under the hood on my drive home was that they disconnected the vacuum line from the fuel rail pressure sensor and simply plugged the line on a random bolt.
Also, the truck apparently has a cam phaser lockout on it and I dont know if that could be causing the issue? Here's a list of some of the troubleshooting ive done so far.
-checked all fuses(start at the basics eh)
-checked resistance of coils(checked out fine, even after engine was warm)
-pulled spark plug 1 and 5, they both seemed fairly clean, not fowled up
-generally looked over all the vacuum lines, seemed fine couldn't see anything else really out of the ordinary
-while the truck was running I used a temperature gauge to see what the exhaust system was doing. On the drivers side when the truck was warm before the cat I had 140C and after the cat it was 80C(good indication the cat is plugged?) The other side tested fairly consistent.
View 9 Replies
My '05 F250 (5.4) started misfiring and threw codes for p0300, p0305, p0307, p0308,and p2198. I used an inline spark checker to check cops, which all had spark. Replaced 5, 6, 7, and 8 plugs and cleared codes. Ran truck for a few minutes and codes came back. Switched #5 and #6 cops and cleared codes. 5,7,and 8 cylinders still misfiring (same codes). Truck only has 36,000 miles and spent alot of time just sitting. Plugs were original plugs.
Replaced 5-8 with Autolite OEM replacements. I haven't checked cops for resistance yet. Weather was pretty cold when problem started. Threw in about 10oz. of Lucas to no avail. I had this problem last winter with the same cylinders throwing codes. Threw some Lucas in the tank and idled truck for approx. 1/2 hour and problem went away except for stumbling most every time truck came to a stop. I'm starting to wonder if it's a coil or a fuel issue.
View 10 Replies
I have a 2002 F250 5.4 L with an intermittent Misfire. A little history on the truck in 2011 I replaced the motor with a Ford long block motor, only the block, I used my electronics, intake, etc, this was brand new from Ford. The truck has a total of over 300K miles. Recently it has developed an intermittent misfire. I have changed all the coils and plugs and the misfire is still present. The codes are showing a misfire in cylinder 3 but could be 4 too. The misfire is intermittent because this morning I changed the plugs and truck ran fine, drove to store and it started missing, turned truck off and started up and ran fine again. It has been doing this off and on for a few weeks.
View 10 Replies
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 Replies
I bought this 2004 V10 Ford truck new.. It was at that time top of the line Ranch King with all the bells and whistles.. I have been trying for some time to figure out the miss I have. I was told yesterday that.. Misfire 2nd cylinder passenger side no compression.. They said I need to have a new Engine installed.. They would look for a rebuilt and would cost with installation around 5 grand.. I then took it to another garage and was told that's not it, but will check it out later in the week.. What I should look for.. No one seems to b able to figure it out.. I cannot afford a new truck at this time and 5 grand for this one to fix is not a reality..
View 8 Replies
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
View 10 Replies
I have a 99 ford super duty with a 5.4 triton that is having a troublesome misfire. When you first fire it up it has a bit of a stutter then runs relatively smooth but the engine does still have a small shake to it and you can hear a bit of a choppy sound in the exhaust. Not completely smooth. When you drive it light footed it seems to run perfectly smooth and nice. But if you go past half throttle (sometimes you can go past that point) it starts to cough and is very slow at picking up.
When you reach between 3,250 and 4,500rpm the coughing stops. But the pick up is a little surgy, not steady. It was doing this for a while before the engine light came on. I got it scanned and it showed a miss fire on cylinder two so I have replaced the spark plug, coil, and injector but still the same issue. I opened up the catalytic converter to see if it was plugged up. Nothing there.
View 11 Replies
99 F-250 SD 6.8 had an issue with it while moving from Del to Phx, Az. Found collapsed air cleaner element. It looked like someone stepped on it. I replaced it as well as the MAF. This fixed the issue. This was 350 miles into the trip. The truck seemed to be down on power as it didn't want to pull my trailer up any type of grade except with OD off. Around 2K miles into the trip in developed a random misfire with no codes. I am at my final destination and the misfire is worse. I am not showing any codes at all or pending either. It is a bit toasty outside to be out there diagnosing issues, and I won't start changing parts randomly either. I have a NGS scan tool with the proper cards.
View 5 Replies
My dad gave his 2005 Ford F-350 truck with the gas 5.4L (?) I drove it home. If i floor it it misfires badly, or if the RPM's get over 3000 it misfires then about 3800 it stops and keeps going. but i can't give it to much gas....
The spark plugs where replaced 2 years ago along with the cat converters. I can hear some very fait manifold gasket leak ...
A few days ago it was raining and it had a bad misfire with blinking CEL. but it never threw a solid CLE. can i still put the codes on it to see what cylinder it is? Are these issue related? Where should i start?
View 8 Replies
I have a 2000 f350 5.4 liter I recently fixed a misfire in cylinder 1 since then every morning the truck runs perfectly fine however at night when I leave work around 6 o'clock the truck has a misfire again I stopped pullover pull the spark plug out put the spark plug back in and it runs perfectly fine all over again I don't know if this matters but when I replace the spark plug I only replaced one and not all 8 same thing with the new coil pack I don't see how that could cause this.
View 14 Replies
2003 f350 2wd 5.4 auto cab and chassis with 40 gal rear tank replaced fuel pump/fuel filter/spark plugs/IAC no codes
View 7 Replies
1995 7.3L f350 400k mi developed 1poss 2 cyl miss does not change after warm up and will die after 10 min .
View 1 Replies
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
View 2 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
