I have 08 f250 6.4 was driving down the road truck just died. Will turn over but not crank. I've checked oil level, water level, fuses, fuel cut off switch. Still no start.
View 3 RepliesThis is a 6.4L powerstroke, but this is not an engine specific problem. I have a no crank condition that appeared overnight while parked in the driveway. I CAN start it by using the solenoid connector wire near the air filter box and supplying 12v from + battery post. I THINK that eliminates batteries, solenoid and starter.
Now that leaves Trans range sensor or (NSS) and the ignition switch. I can test and get 12V (light) on the Blu/Wh wire from ign sw when turned to start, so that seems good. And as far as I can tell the trans range sensor is internal to the tranny, and I really don't want to go there if possible....
Also there are no codes on the Solus scanner I borrowed. And the voltage is showing as 11.7 on the scanner....is that low enough to prevent voltage from being sent to the solenoid thru the SJB and/or PCM even though engine will start as described?
I have an issue with my 2008 f250 6.4 where the gauge cluster is dark and truck won't crank. The only light on the dash is the airbag light. I have tried reprogamming with my Spartan tuner, checked fuses, removed aftermarket alarm, charged batteries. I scanned and got two codes. P1260 theft detected and a u code no comm with cluster.
View 7 RepliesMy father-in-law has a 2008 f-250 with the 5.4. as he was driving a while back all the gauges of the dash quit. The engine still kept running without any noticeable difference but when he shut the engine off and tried to restart, it wouldn't even crank but the security light was flashing. He tried starting it again a few hours later and it started just like normal and ran fine.
He has had this problem occur several times in the last few months, but the other day it repeated the problem again and would not restart for about 5 days. He has tried charging the batteries, changing relays, checking all fuses and finding none blown, scanned it with his code reader, and checked the steering column for bare or rubbed wires.
On my 2008 f250 I can not turn the hubs without a set of pliers...does that mean I need new hubs....
What auto tranny do I have with the 5.4.. is it a six speed...
Just bought this '08 F250 CCSB 4X4 5.4 Problem is the steering seems heavy, it tends to wander at higher speeds and won't return to center after a turn. I've searched on here and found a few possibilities (axle u joints, ball joints, steering gear, etc). I have an appointment with the dealer on Friday to fix it under warranty but he is convinced it's the u joints in the steering shaft seizing. When my F150 steering shaft began to seize, it would be hard to turn then break free then be hard then break free and this is not what is happening on the SD. I haven't had a chance to check the front end myself but not sure how you would check the axle u joints if there was no play in them. How would you check to see if they were seizing up.
View 3 RepliesI have a 2008 F250 XLT. When i am driving and turn the wheel a squeak is noticeable while the tire is spinning. as i speed up the squeak gets faster and slower when i slow down. I have it narrowed down to the right front tire but cant figure out what is causing it.
View 5 Replies2001, F250, Lariat, Super Duty, 7.3 engine with towing package.
It ran seemingly perfect when I parked it and it sat for maybe 10 days to 2 weeks and wouldn't crank. Battery is fine and fully charged. Glow plug heaters work OK. Engine spins really fast, almost like it had no compression. (Not sure though) Temperature in the 30's -50's. I did some research on line and decided to change the Cam Positioning Sensor (CPS). Didn't work, still won't crank. I originally tried my Cheap Harbor Freight OBDII . (Don't waste your money, IMO). What should I troubleshoot next/ or try.
Ok I have a 99 f250sd v10 with 180k miles. Original owner and have most work my self over the years. Son took the truck to fill it up, started fine ,filled it up and now will not start. It has power but will not crank. Tries to but no good. I was thinking battery died. New battery same results. Sort of tried to start but not turning over. With the new battery i tried several times then nothing. No power at all. No lights, nothing. So I put the old battery back in and still no power at all. I'm thinking the starter is toast and my repeated attempts to start that I pulled too many amps and blew a master fuse? It stilling in a parking lot until tonight when I can tow it home. Where to start.
View 9 RepliesLet me start out by saying that I have exhausted every option that I have read on every thread that I could find on the internet regarding my son's 2002 7.3L not starting. What I have is no 12v power to the starter solenoid at the starter when I crank the key. What we have done so far, had the starter and both batteries tested, all good. Swapped out the starter motor fuse and the starter relay. Tried a new ignition switch and a new trans position sensor. Found major corrosion in the fusible link junction box on the drivers inner fender so we cut out the fusible links and put in a temporary jumper wire, still no crank. I have power to the dash, power on the power cable at the starter. I can jump the terminals on the starter and the starter engages. I found the shifter linkage bolts loose under the dash and tightened them up also. We have been struggling with this for 3 days, out in the lovely Michigan weather, since it couldn't have died in his parking spot in our heated shop, and I am completely frustrated. Are we overlooking something glaringly obvious?
View 11 RepliesI have a 99 f250 sd with v10 that has no power. Will crank, idle and die sometimes. Getting codes p0351 - p0355. No power when driving.
View 11 RepliesOn occasion, the last 2 weeks, my truck doesn't like to start, sometimes it will start to crank for one second and then quit. i've tried moving my gear shift through the drive selection range (park, neutral, reverse and drive). i just replaced the starter relay on the fender well because i can always start the truck by jumping across the terminals... no joy. So now ( i think) my issue is between the key switch and the starter relay. i replaced the neutral safety switch about 18 months ago.
99 F250 V10 short bed, 123,000 miles ....
So I have a 2003 6.0L Powerstroke 1 ton. I just replaced the starter thinking the solenoid was the problem. But my luck it wasn't. I turn the key and the ding stops and it's quiet. Dash lights go off. I have the engine light and water in fuel light on. ABS is on I think aswell. I've run out of options.
View 1 RepliesI have been trouble shooting a no crank no start issue for a couple years now. Been back to the dealer several times to no avail. Very long story, with all due respect, don't suggest that I go back to the dealer on this. Not happening. Every once in a while the truck would strand me with no crank no start. It would read trailer brake module fault. Sometimes the security light would flash and the alarm would sound. Recently, I have had it on IDS and noticed that while it was doing this, IDS had no communication to the ECU.
I checked IDS with my other truck and it had good communication with that ECU so I know the computer/IDS works. Pulled battery cables and checked all the fuses... checked ok. Went back in the truck tried it, still no crank. Left key on, popped hood to listen for fuel pump... nothing. Went to pop cover off the fuse block and as soon as I touched it the fuel pump started whining. Went back in the truck and it started. Plugged IDS back in and had good communication and read ECU. I googled around for a part number but came up empty.
2002 F250 V10....
Ambient temp is 4-9 degrees
Step-son borrowed truck. I started it at 9 in the morn and moved it to a different parking spot on street. No problem starting.
Step-son came at 11 and took truck. It started no problem.
He drove it to work. At 5 p.m. would crank, but not start. A jump got it running.
On charger all night. Would not crank this morn. Would not crank even when jumped.
Are we looking at a bad battery or something else?
I'm having a problem with my 04 f250 6.0. I replaced my brakes rotors and calipers yesterday along with my fuel filters and after I took out my air filter to check it and put it back in my truck will no longer crank. When I put my key in the on position all of my lights and dings happen but I don't hear my fuel pump and when I go to turn it over I get nothing at all.
View 8 RepliesI have a ford f250 super duty and it wont start I have checked obvious reasons and I think it might be a crank shaft sensor. Just curious, is there two of them one for right bank and left bank or just one on drivers side?
View 2 RepliesI have a 2004 Ford F-250 with the 6.0 egr has been deleted and so on. Truck has been very trustworthy until now... It all started last week. I would get in and it would fire right up, drive 15 miles to work all is still good. Time to go home try to start and it would act like the batteries were weak with a weak crank until it finally takes off and starts. This intermittent situation has been happening but I just assumed that the batteries were going bad. I drove to work this morning truck fired right up and now that it is time to go home the truck only has a weak crank and wont fire up. I tested the batteries and they were low on cranking amps.
Replaced them with two new batteries. The issue still exists and didn't change. After reading through threads I found that it could be the FICM I checked it out as was shown through the other threads. With the key on only it was reading 51 vdc with someone trying to start the truck it was reading 48-50 vdc... Yes the truck does have fuel in it and yes the oil is good to. It seems that there is something electrical going on for sure due to the way it has been an intermittent problem for a week or so. I am an aircraft mechanic by trade but can fix anything if I know where to start.
My '99 Super Duty does NOT have power windows; old school cranks. The door panel(s) are "no frilz", no storage pockets. I want to know if it's possible to get panels that DO have pockets and will "fit" my crank handles?
I could always just drill a hole into a door panel that has the pockets for the window crank, but, they all seem to come with power window setups (opening for all the power switches). Also, where I can get rugs to cover the floor - I just have a rubbery/plastic surface.
My 92 f250 5.8l 5 speed, out of no where when I try to start it I get absolutely nothing, when I put the key in the on position and short the solenoid it starts up that's how I've been starting it? When I try to start it regularly it's almost as if trying to start it without pressing the clutch it literally does nothing.
View 1 RepliesI have 1999 f250 powerstroke, batteries are fully charged but when you put key in ignition and turn you get nothing. No dash lights, no crank, nothing. I cleaned the battery terminals on both batteries, checked all the fuses under the dash and the hood.
View 9 Replies